| Age | Commit message (Collapse) | Author |
|---|
|
|
|
This needs to be set to avoid a fatal error when ECC is used.
Signed-off-by: Andre Renaud <andre@designa-electronics.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
|
|
This uses the wrote base register value. Fix it.
Signed-off-by: Andre Renaud <andre@designa-electronics.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
|
|
|
|
support in omap_nand_switch_ecc() also an eccstrength
from 16.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
add for nand devices mtd concat support. Generic MTD concat
support is already ported to mainline, and used in the cfi_mtd
driver. This patch adds it similiar for nand devices.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
|
|
The mtd subsystem deprecated and renamed the direct use of the mtd_info
struct's functionpointers. Instead the corresponding mtd_xxx function
should be used.
See also:
https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=3c3c10bba1e4ccb75b41442e45c1a072f6cded19
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
|
|
Updates the NAND code to match Linux v4.6. The previous sync was from
Linux v4.1 in commit d3963721d93fafa.
Note that none of the individual NAND drivers tracked Linux closely
enough to be synced themselves, other than manually applying a few
cross-tree changes.
Signed-off-by: Scott Wood <oss@buserror.net>
Tested-by: Heiko Schocher <hs@denx.de>
|
|
This change is part of the Linux 4.6 sync. It is being done before the
main sync patch in order to make it easier to address the issue across
all NAND drivers (many/most of which do not closely track their Linux
counterparts) separately from other merge issues.
Signed-off-by: Scott Wood <oss@buserror.net>
|
|
These functions are part of the Linux 4.6 sync. They are being added
before the main sync patch in order to make it easier to address the
issue across all NAND drivers (many/most of which do not closely track
their Linux counterparts) separately from other merge issues.
Signed-off-by: Scott Wood <oss@buserror.net>
|
|
nand_info[] is now an array of pointers, with the actual mtd_info
instance embedded in struct nand_chip.
This is in preparation for syncing the NAND code with Linux 4.6,
which makes the same change to struct nand_chip. It's in a separate
commit due to the large amount of changes required to accommodate the
change to nand_info[].
Signed-off-by: Scott Wood <oss@buserror.net>
|
|
This typedef serves no purpose other than causing confusion with
struct nand_chip.
Signed-off-by: Scott Wood <oss@buserror.net>
|
|
Commit ad4f54ea86b ("arm: Remove palmtreo680 board") removed the only
user of the docg4 driver and the palmtreo680 image flashing tool. This
patch removes them.
Signed-off-by: Scott Wood <oss@buserror.net>
Cc: Mike Dunn <mikedunn@newsguy.com>
Cc: Simon Glass <sjg@chromium.org>
|
|
This driver is not used by anyone, remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Scott Wood <oss@buserror.net>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Scott Wood <oss@buserror.net>
|
|
Correct the nand ecc initialization code
This fixes the issue of incorrect nand ecc
init if no device is found in ecc_matrix then
it endsup ecc init with junk initialization
instead of the most suited one.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
|
|
Serial number, vendor id and page size are added for QSPI flash
common on both LS1012AQDS and LS1012ARDB i.e. S25FS512SDSMFI011.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
When offset is not aligned to page address, it is possible that extra offset
will be read from nand. Adjust the image such that first byte of the image
is at load address after the first page is read.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Detect a FIT when loading from SPI and handle it using the
new FIT SPL support.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
|
|
Use simpler runtime cpu dection macros.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Scott Wood <oss@buserror.net>
|
|
PIC32 internal flash devices are parallel NOR flash divided into
number of banks to allow erase-programming in one while fetch and
execution continues on other. As the flash banks are memory mapped
stored code can be executed directly from flash (XIP), also there
is additional hardware logic to prefetch and cache contents to
improve execution performance. These flash can also be used to
store user data (like environment).
Flash erase and programming are handled by on-chip NVM controller.
Driver implemented driver model but MTD is not really support.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The S25FS-S family physical sectors may be configured as a hybrid
combination of eight 4-kB parameter sectors at the top or bottom
of the address space with all but one of the remaining sectors
being uniform size.
The default status of the flash is in this hybrid architecture.
The parameter sectors and the uniform sectors have different erase
commands.
This patch disable the hybrid sector architecture then the flash will
has uniform sector size and uniform erase command.
This configuration is temporary, the flash will revert to hybrid
architecture after power on reset.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
The flash type of LS2085AQDS QSPI is S25FS256S. It has special write
any device register command and read any device register command.
This patch enable support for those commands.
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Allow the spl_parse_image_header() to return value. This is convenient
for controlling the SPL boot flow if the loaded image is corrupted.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <van.freenix@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@konsulko.com>
|
|
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
get_timer() returns an unsigned 64-bit value, but is currently assigned to
a signed 32-bit variable. Due to sign extension and data truncation, this
causes the timeout loop in spi_flash_cmd_wait_ready() to immediately (and
incorrectly) fire for about 50% of all time values, based on whether bit
31 is set. In sandbox at least, this causes the test to pass or fail based
on system uptime, as opposed to time since the U-Boot binary was started.
Fixes: 4efad20a1751 ("sf: Update status reg check in spi_flash_cmd_wait_ready")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
|
Set free_count to zero before walking through ai->erase list
in wl_init().
As U-Boot has no workqueue/threads, it immediately calls
erase_worker(), which increase for each erased block
free_count. Without this patch, free_count gets after
this initialized to zero in wl_init(), so the free_count
variable always has the maybe wrong value 0.
Detected this behaviour on the dxr2 board, where the
UBI fastmap gets not written when attaching/dettaching
on an empty NAND. It drops instead the error message:
could not find any anchor PEB
With this patch, fastmap gets written on dettach.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Unlock current sector instead of sector 0 before buffered write.
[Patch subject and commit text slightly reworded, Stefan]
Signed-off-by: Rouven Behr <u-boot@behr-iss.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
After writing data to flash space, next instruction is checking if flash
controller is busy writing to the flash memory. Memory barrier is required here
to avoid transaction re-ordering for data write and busy status check.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
|
|
Definition of writes{bwlq}, reads{bwlq} are now added into arch specific
asm/io.h. So removing them from driver to fix re-definition error
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
|
|
Claim the MPP pins for the NAND flash controller only when it's actually
being used. This allows the pins to be shared with the SPI interface
which already supports an equivalent on-access MPP reconfiguration.
Reviewed-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Read Denali hardware revision number and use it to
calculate max_banks, The encoding of max_banks changed
in Denali revision 5.1.
[ Linux commit : 271707b1d817f5104e02b2bd1bab43f0c8759418 ]
Signed-off-by: Graham Moore <grmoore@opensource.altera.com>
[Brian: parentheses around macro arg]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[Masahiro: import from Linux and adjust ioread32() to readl() ]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Otherwise flash remains in read status mode and it's not possible
to access data on flash.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
|
|
Same flash driver can be used by other stm32 families like stm32f7.
Better place for this driver would be mtd driver location.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
|
|
The 64-bit compiler (ex. aarch64) emits "warning: cast from pointer
to integer of different size".
Make it work with 64bit DMA address while I am here.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
The stm_is_locked_sr() function is picked from Linux kernel. For reason
unknown, the 64bit data types used by the function and present in Linux
were replaced with 32bit unsigned ones, which causes trouble.
The testcase performed was done using ST M25P80 chip.
The command used was:
=> sf protect unlock 0 0x10000
The call chain starts in stm_unlock(), which calls stm_is_locked_sr()
with negative ofs argument. This works fine in Linux, where the "ofs"
is loff_t, which is signed long long, while this fails in U-Boot, where
"ofs" is u32 (unsigned int). Because of this signedness problem, the
expression past the return statement to be incorrectly evaluated to 1,
which in turn propagates back to stm_unlock() and results in -EINVAL.
The correction is very simple, just use the correctly sized data types
with correct signedness in the function to make it work as intended.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
|
When an error number is provided we should use it, not change it. This fixes
the SPI and SPI flash tests.
One of these is long-standing. The other seems to have been introduced by
commit 1e90d9fd (sf: Move read_id code to sf_ops).
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 1e90d9fd (sf: Move read_id code to sf_ops)
Reviewed-by: Jagan Teki <jteki@openedev.com>
Tested-by: Jagan Teki <jteki@openedev.com>
|
|
We must not free data that is managed by driver mode. Remove this line,
which is a hangover from the pre-driver-model code.
This fixes a problem where 'sf probe' crashes U-Boot if the backing file
for the SPI flash cannot be found.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Add a little more debugging to help when things go wrong.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Tested-by: Jagan Teki <jteki@openedev.com>
|
|
Add dma memcpy api to the default spi_flash_copy_mmap(), so that
dma will be used to copy data when CONFIG_DMA is defined for the
platform.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
|
Added initial nand driver support for arasan nand flash
controller.This supports nand erase,nand read, nand write
This uses the hardware ECC for read and write operations
ZynqMP uses this driver.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
[scottwood: Fix checkpatch warnings]
Signed-off-by: Scott Wood <oss@buserror.net>
|
|
Add nand driver support for zynqmp. The Nand
controller used in ZynqMP is Arasan Nand Flash
controller.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
[scottwood: Fix checkpatch warning]
Signed-off-by: Scott Wood <oss@buserror.net>
|
|
The allocation size is reduced from what was introduced from the
Linux kernel, as U-boot uses the statically allocated nand_info
instead of needing to dynamically allocate an mtd_info instance.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Scott Wood <scottwood@freescale.com>
|
|
Correct some pointer math in initialization. An offset was added
to a struct-typed pointer instead of one casted to a byte-size,
resulting in a much larger offset than intended.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Scott Wood <scottwood@freescale.com>
|
|
Correct a null pointer dereference in board_nand_init(). Zeroed
memory was allocated, then immediately dereferenced. The
dereference is completely removed, since this pointer is later
initialized in alloc_nand_resources.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Scott Wood <scottwood@freescale.com>
|
|
Fix error handling for mxs_nand_init.
The original error handling is wrong for err2 and err1.
Should first free desc[x], then free desc.
This patch also correctly handle err3, should use
MXS_DMA_CHANNEL_AHB_APBH_GPMI0 as the check point.
Cc: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <Fabio.Estevam@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Also if minimum ecc requirment is bigger then what we support, then just
use our maxium pmecc support.
But it is not safe, so we'll output a warning about this.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
1. add the pmecc register mapping for sama5d2.
2. add the pmecc error location register mapping for sama5d2.
3. add some new field that is different from old ip.
4. add sama5d2 pmecc ip version number.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
