| Age | Commit message (Collapse) | Author |
|---|
|
|
|
Freescale IFC controller has been used for mpc8xxx. It will be used
for ARM-based SoC as well. This patch moves the driver to driver/misc
and fix the header file includes.
Signed-off-by: York Sun <yorksun@freescale.com>
|
|
This patch adds new CONFIG_NAND_OMAP_ECCSCHEME, replacing other distributed
CONFIG_xx used for selecting NAND ecc-schemes.
This patch aims at solving following issues.
1) Currently ecc-scheme is tied to SoC platform, which prevents user to select
other ecc-schemes also supported in hardware. like;
- most of OMAP3 SoC platforms use only 1-bit Hamming ecc-scheme, inspite
the fact that they can use higher ecc-schemes like 8-bit ecc-schemes with
software based error detection (OMAP_ECC_BCH4_CODE_HW_DETECTION_SW).
- most of AM33xx SoC plaforms use 8-bit BCH ecc-scheme for now, but hardware
supports BCH16 ecc-scheme also.
2) Different platforms use different CONFIG_xx to select ecc-schemes, which
adds confusion for user while migrating platforms.
- *CONFIG_NAND_OMAP_ELM* which enables ELM hardware engine, selects only
8-bit BCH ecc-scheme with h/w based error-correction (OMAP_ECC_BCH8_CODE_HW)
whereas ELM hardware engine supports other ecc-schemes also like; BCH4,
and BCH16 (in future).
- *CONFIG_NAND_OMAP_BCH8* selects 8-bit BCH ecc-scheme with s/w based error
correction (OMAP_ECC_BCH8_CODE_HW_DETECTION_SW).
- *CONFIG_SPL_NAND_SOFTECC* selects 1-bit Hamming ecc-scheme using s/w library
Thus adding new *CONFIG_NAND_OMAP_ECCSCHEME* de-couples ecc-scheme dependency
on SoC platform and NAND driver. And user can select ecc-scheme independently
foreach board.
However, selection some hardware based ecc-schemes (OMAP_ECC_BCHx_CODE_HW) still
depends on presence of ELM hardware engine on SoC. (Refer doc/README.nand)
Signed-off-by: Pekon Gupta <pekon@ti.com>
|
|
BCH8_ECC scheme implemented in omap_gpmc.c driver has following favours
+-----------------------------------+-----------------+-----------------+
|ECC Scheme | ECC Calculation | Error Detection |
+-----------------------------------+-----------------+-----------------+
|OMAP_ECC_BCH8_CODE_HW |GPMC |ELM H/W engine |
|OMAP_ECC_BCH8_CODE_HW_DETECTION_SW |GPMC |S/W BCH library |
+-----------------------------------+-----------------+-----------------+
Current implementation limits the BCH8_CODE_HW only for AM33xx device family.
(using CONFIG_AM33XX). However, other SoC families (like TI81xx) also have
ELM hardware module, and can support ECC error detection using ELM.
This patch
- removes CONFIG_AM33xx
Thus this driver can be reused by all devices having ELM h/w engine.
- adds omap_select_ecc_scheme()
A common function to handle ecc-scheme related configurations. This
can be used both during device-probe and via user-space u-boot commads
to change ecc-scheme. During device probe ecc-scheme is selected based
on CONFIG_NAND_OMAP_ELM or CONFIG_NAND_OMAP_BCH8
- enables CONFIG_BCH
S/W library (lib/bch.c) required by OMAP_ECC_BCHx_CODE_HW_DETECTION_SW
is enabled by CONFIG_BCH.
- enables CONFIG_SYS_NAND_ONFI_DETECTION
for auto-detection of ONFI compliant NAND devices
- updates following README doc
doc/README.nand
board/ti/am335x/README
doc/README.omap3
Signed-off-by: Pekon Gupta <pekon@ti.com>
[scottwood@freescale.com: fixed unused variable warning]
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
platforms
ELM hardware engine which is used for ECC error detection, is present on all
latest OMAP SoC (like OMAP4xxx, OMAP5xxx, DRA7xxx, AM33xx, AM43xx). Thus ELM
driver should be moved to common drivers/mtd/nand/ folder so that all SoC
having on-chip ELM hardware engine can re-use it.
This patch has following changes:
- mv arch/arm/include/asm/arch-am33xx/elm.h arch/arm/include/asm/omap_elm.h
- mv arch/arm/cpu/armv7/am33xx/elm.c drivers/mtd/nand/omap_elm.c
- update Makefiles
- update #include <asm/elm.h>
- add CONFIG_NAND_OMAP_ELM to compile driver/mtd/nand/omap_elm.c
and include in all board configs using AM33xx SoC platform.
Signed-off-by: Pekon Gupta <pekon@ti.com>
|
|
Signed-off-by: Josh Wu <josh.wu@atmel.com>
|
|
Since for some MLC nand, bit errors happened too often. Just disable it
to avoid noise
Signed-off-by: Josh Wu <josh.wu@atmel.com>
|
|
increase the delay to 75us to support the 8k bytes page nand flash
Signed-off-by: Josh Wu <josh.wu@atmel.com>
|
|
Current IFC driver supports till 4K page size NAND flash.
Add support of 8K NAND flash
- Program Spare region size in csor_ext
- Add nand_ecclayout for 4 bit & 8 bit ecc
- Defines constants
- Add support of 8K NAND boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
CC: Liu Po <po.liu@freescale.com>
|
|
nand_ecclayout is present in mtd.h at Linux.
Move this structure to mtd.h to comply with Linux.
Also, increase the ecc placement locations to 640 to suport device having
writesize/oobsize of 8KB/640B. This means that the maximum oobsize has gone
up to 640 bytes and consequently the maximum ecc placement locations have
also gone up to 640.
Changes from Prabhabkar's version (squashed into one patch to preserve
bisectability):
- Added _LARGE to MTD_MAX_*_ENTRIES
This makes the names match current Linux source, and resolves
a conflict between
http://patchwork.ozlabs.org/patch/280488/
and
http://patchwork.ozlabs.org/patch/284513/
The former was posted first and is closer to matching Linux, but
unlike Linux it does not add _LARGE to the names. The second adds
_LARGE to one of the names, and depends on it in a subsequent patch
(http://patchwork.ozlabs.org/patch/284512/).
- Made max oobfree/eccpos configurable, and used this on tricorder,
alpr, ASH405, T4160QDS, and T4240QDS (these boards failed to build
for me without doing so, due to a size increase).
On tricorder SPL, this saves 2576 bytes (and makes the SPL build
again) versus the new default of 640 eccpos and 32 oobfree, and
saves 336 bytes versus the old default of 128 eccpos and 8 oobfree.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
CC: Vipin Kumar <vipin.kumar@st.com>
[scottwood@freescale.com: changes as described above]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Cc: Stefan Roese <sr@denx.de>
Cc: York Sun <yorksun@freescale.com>
Cc: Tom Rini <trini@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
as per controller description,
"While programming a NAND flash, status read should never skipped.
Because it may happen that a new command is issued to the NAND Flash,
even when the device has not yet finished processing the previous request.
This may result in unpredictable behaviour."
IFC controller never polls for R/B signal after command send. It just return
control to software. This behaviour may not occur with NAND flash access.
because new commands are sent after polling R/B signal. But it may happen
in scenario where GPCM-ASIC and NAND flash device are working simultaneously.
Update the controller driver to take care of this requirement
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
|
|
Add possible to use software BCH ECC for atmel nand driver
Signed-off-by: Bo Shen <voice.shen@gmail.com>
|
|
Conflicts:
arch/arm/cpu/arm926ejs/mxs/Makefile
board/compulab/cm_t35/Makefile
board/corscience/tricorder/Makefile
board/ppcag/bg0900/Makefile
drivers/bootcount/Makefile
include/configs/omap4_common.h
include/configs/pdnb3.h
Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:
board/compulab/common/Makefile
board/udoo/Makefile
include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.
include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.
Note: 'git show' will also list two files just because
they are new:
include/configs/am335x_igep0033.h
include/configs/omap3_igep00x0.h
|
|
enable the RBL/UBL ECC layout through
CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC define
see for more info:
http://processors.wiki.ti.com/index.php/DM365_Nand_ECC_layout
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Scott Wood <scottwood@freescale.com>
|
|
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
Prior to SPDX licensing this file was GPL-2.0 with Freescale granting
rights for "or later" for their contributed code. We incorrectly moved
this file to GPL-2.0+, so correct it to GPL-2.0. In addition we cannot
easily denote in the file where or what code is "or later", so just set
that aside for now and the file as a whole is GPL-2.0 regardless.
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Tom Rini <trini@ti.com>
|
|
NAND_ECC_SOFT was the only option available while the SOFT_BCH option
may also be used.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: Scott Wood <scottwood@freescale.com>
|
|
As the spi flash transfer to multiple parts, it is forgot to add
Atmel AT25DF321 spi flash support, which broken several Atmel EK
boards which this chip. So, add it
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
|
|
Added GPL-2.0+ SPDX-License-Identifier for missed sf
source files.
Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
|
|
- Add comments.
- Renamed few macros.
- Add tabs.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
|
|
Unified the bank_sel calculation code for erase and
write ops.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Drop changes for PEP 4 following python tools]
Signed-off-by: Tom Rini <trini@ti.com>
|
|
|
|
Linux modified the MTD driver interface in commit edbc4540 (with the
same name as this commit). The effect is that calls to mtd_read will
not return -EUCLEAN if the number of ECC-corrected bit errors is below
a certain threshold, which defaults to the strength of the ECC. This
allows -EUCLEAN to stop indicating "some bits were corrected" and begin
indicating "a large number of bits were corrected, the data held in
this region of flash may be lost soon". UBI makes use of this and when
-EUCLEAN is returned from mtd_read it will move data to another block
of flash. Without adopting this interface change UBI on U-boot attempts
to move data between blocks every time a single bit is corrected using
the ECC, which is a very common occurance on some devices.
For some devices where bit errors are common enough, UBI can get stuck
constantly moving data around because each block it attempts to use has
a single bit error. This condition is hit when wear_leveling_worker
attempts to move data from one PEB to another in response to an
-EUCLEAN/UBI_IO_BITFLIPS error. When this happens ubi_eba_copy_leb is
called to perform the data copy, and after the data is written it is
read back to check its validity. If that read returns UBI_IO_BITFLIPS
(in response to an MTD -EUCLEAN) then ubi_eba_copy_leb returns 1 to
wear_leveling worker, which then proceeds to schedule the destination
PEB for erasure. This leads to erase_worker running on the PEB, and
following a successful erase wear_leveling_worker is called which
begins this whole cycle all over again. The end result is that (without
UBI debug output enabled) the boot appears to simply hang whilst in
reality U-boot busily works away at destroying a block of the NAND
flash. Debug output from this situation:
UBI DBG: ensure_wear_leveling: schedule scrubbing
UBI DBG: wear_leveling_worker: scrub PEB 1027 to PEB 4083
UBI DBG: ubi_io_read_vid_hdr: read VID header from PEB 1027
UBI DBG: ubi_io_read: read 4096 bytes from PEB 1027:4096
UBI DBG: ubi_eba_copy_leb: copy LEB 0:0, PEB 1027 to PEB 4083
UBI DBG: ubi_eba_copy_leb: read 1040384 bytes of data
UBI DBG: ubi_io_read: read 1040384 bytes from PEB 1027:8192
UBI: fixable bit-flip detected at PEB 1027
UBI DBG: ubi_io_write_vid_hdr: write VID header to PEB 4083
UBI DBG: ubi_io_write: write 4096 bytes to PEB 4083:4096
UBI DBG: ubi_io_read_vid_hdr: read VID header from PEB 4083
UBI DBG: ubi_io_read: read 4096 bytes from PEB 4083:4096
UBI DBG: ubi_io_write: write 4096 bytes to PEB 4083:8192
UBI DBG: ubi_io_read: read 4096 bytes from PEB 4083:8192
UBI: fixable bit-flip detected at PEB 4083
UBI DBG: schedule_erase: schedule erasure of PEB 4083, EC 55, torture 0
UBI DBG: erase_worker: erase PEB 4083 EC 55
UBI DBG: sync_erase: erase PEB 4083, old EC 55
UBI DBG: do_sync_erase: erase PEB 4083
UBI DBG: sync_erase: erased PEB 4083, new EC 56
UBI DBG: ubi_io_write_ec_hdr: write EC header to PEB 4083
UBI DBG: ubi_io_write: write 4096 bytes to PEB 4083:0
UBI DBG: ensure_wear_leveling: schedule scrubbing
UBI DBG: wear_leveling_worker: scrub PEB 1027 to PEB 4083
...
This patch adopts the interface change as in Linux commit edbc4540 in
order to avoid such situations. Given that none of the drivers under
drivers/mtd return -EUCLEAN, this should only affect those using
software ECC. I have tested that it works on a board which is
currently out of tree, but which I hope to be able to begin
upstreaming soon.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Stefan Roese <sr@denx.de>
|
|
There is no page_size for ramtron flashes,
so just print the detected flash and it's size.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
|
- Add spaces, tabs
- Commenting.
- Rearrange code.
- Add static qualifier for missing func.
- Remove memory_map from ramtron.c
- Ramtron: spi_flash_internal.h -> sf_internal.h
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
|
Qspi controller can have a memory mapped port which can be used for
data read. Added support to enable memory mapped port read.
This patch enables the following:
- It enables exchange of memory map address between mtd and qspi
through the introduction of "memory_map" flag.
- Add support to communicate to the driver that memory mapped
transfer is to be started through introduction of new flags like
"SPI_XFER_MEM_MAP" and "SPI_XFER_MEM_MAP_END".
This will enable the spi controller to do memory mapped configurations
if required.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
|
|
Add support for EON EN25S64 SPI flash.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
|
Renamed:
spi_flash.c -> sf.c
spi_flash_internal.h -> sf_internal.h
spi_flash_ops.c -> sf_ops.c
spi_flash_probe.c -> sf_probe.c
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
|
More cleanups on spi_flash side:
- Removed unneeded comments.
- Rearranged macros in proper location.
- Rearranged func declerations
- Renamed few function names.
- Added License headers.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
|
Add support for Macronix MX25L51235F SPI flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
|
Add support for Macronix MX25L25635F SPI flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
|
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
|
Included erase_size while printing probed flash details.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
|
Use flash->page_size arg in print_size() instead of
flash->sector_size while printing detected flas part details.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
|
Add support for Spansion S25FL512S_256K SPI flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
|
Add support for Spansion S25FL256S_256K SPI flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
|
Add support for EON EN25Q64 SPI flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
|
Now the common probing is handled in spi_flash_probe.c
hence removed the unneeded flash drivers.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
|
Compared to other spi flashes, ramtron has a different
probing and implementation on flash ops, hence moved
ramtron probe code into ramtron driver.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
|
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
|
From Micron, 512MB onwards, flash requires to poll flag status
instead of read status- hence added E_FSR flag on spectific
flash parts.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
|
SECT_4K, SECT_32K and SECT_64K opeartions are performed to
to specific flash by adding a SECT* flag on respective
spi_flash_params.flag param.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
|
Few of the flashes(Atmel, Macronix and SST) require to
clear BP# bits in flash power ups.
So clear these BP# bits at probe time, so-that the flash
is ready for user operations.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
|
Most of the SST flashes needs to write up using SST_WP, AAI
Word Program, so added a flag param on spi_flash_params table.
SST flashes, which supports SST_WP need to use a WP write
sst_write_wp instead of common flash write.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
|
Given proper spacing between flash table params.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
|
Added AT45DB* parts are which are avilable in spi_flash_probe_legacy.c.
Updated the sector_size attributes as per the flash parts.
Looks fine for with this sector_size for computing the size
of flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
|
Added SST25* parts are which are avilable in spi_flash_probe_legacy.c.
Updated the sector_size attributes as per the flash parts.
Looks fine for with this sector_size for computing the size
of flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
|
|
Added S25FL* parts are which are avilable in spi_flash_probe_legacy.c.
Updated the sector_size attributes as per the flash parts.
Looks fine for with this sector_size for computing the size
of flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
|
