summaryrefslogtreecommitdiff
path: root/drivers/net/Kconfig
AgeCommit message (Collapse)Author
2017-03-29net: mvpp2: Enable compilation for Armada 7K/8K platformsStefan Roese
Since Armada 7K/8K is also equipped with a newer version of the MVPP2 ethernet controller, lets enable compilation of this driver for these platforms. Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-02-27drivers/net/Kconfig: Correct use of apostropheTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-02-07drivers: net: Provide Kconfig menu for PHYLIBAlex
Provide the necessary Kconfig symbols so that PHYLIB support may be enabled in Kconfig, as opposed to needing to #define these symbols in C source headers. BITBANGMII and MV88E6352_SWITCH are left out of the PHYLIB submenu as they don't seem to explicitly depend on it (i.e. they do not use the phy_driver class). Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-02-07net: Kconfig: Add CONFIG_MACB optionWenyou Yang
Add CONFIG_MACB option in KConfig to be used to select the Cadence MACB Ethernet driver. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
2017-01-11net: gmac_rockchip: Add Rockchip GMAC driverSjoerd Simons
Add a new driver for the GMAC ethernet interface present in Rockchip RK3288 SOCs. This driver subclasses the generic design-ware driver to add the glue needed specifically for Rockchip. Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Romain Perier <romain.perier@collabora.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-12-16arm: imx: add i.MX53 Beckhoff CX9020 Embedded PCPatrick Bruenn
Add CX9020 board based on mx53loco. Add simplified imx53 base device tree from kernel v4.8-rc8, to reuse serial_mxc with DTE and prepare for device tree migration of other functions and imx53 devices. The CX9020 differs from i.MX53 Quick Start Board by: - use uart2 instead of uart1 - DVI-D connector instead of VGA - no audio - CCAT FPGA connected to emi - enable rtc Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
2016-11-07net: add driver for Synopsys Ethernet QoS deviceStephen Warren
This driver supports the Synopsys Designware Ethernet QoS (Quality of Service) a/k/a eqos IP block, which is a different design than the HW supported by the existing designware.c driver. The IP supports many options for bus type, clocking/reset structure, and feature list. This driver currently supports the specific configuration used in NVIDIA's Tegra186 chip, but should be extensible to other combinations quite easily, as explained in the source. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> # V1 Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-10-26net: Kconfig: Add FEC_MXC entryJagan Teki
Added kconfig for FEC_MXC driver. Cc: Joe Hershberger <joe.hershberger@gmail.com> Cc: Simon Glass <sjg@chromium.org> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Peng Fan <peng.fan@nxp.com> Cc: Matteo Lisi <matteo.lisi@engicam.com> Cc: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-09-21net: emaclite: Enable driver for MIPSZubair Lutfullah Kakakhel
Signed-off-by: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com> Reviewed-by: Paul Burton <paul.burton@imgtec.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-08-15net/ethoc: add Kconfig entry for the driverMax Filippov
Add Kconfig entry for the driver, remove #define CONFIG_ETHOC from the only board configuration that uses it and put it into that board's defconfig. Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-07-15net: Add EMAC driver for H3/A83T/A64 SoCs.Amit Singh Tomar
This patch add EMAC driver support for H3/A83T/A64 SoCs. Tested on Pine64(A64-External PHY) and Orangepipc(H3-Internal PHY). BIG Thanks to Andre for providing some of the DT code. Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-05-31net: Add ag7xxx driver for Atheros MIPSMarek Vasut
Add ethernet driver for the AR933x and AR934x Atheros MIPS machines. The driver could be easily extended to other WiSoCs. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Wills Wang <wills.wang@live.com> [fixed Kconfig dependency] Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2016-04-04net: mvpp2.c: Add Marvell mvpp2 network driver for Armada 375Stefan Roese
This patch adds support for the mvpp2 ethernet controller which is integrated in the Marvell Armada 375 SoC. This port is based on the Linux driver (v4.4), which has been stripped of the in U-Boot unused portions. Tested on the Marvell Armada 375 eval board db-88f6720. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr> Acked-by: Joe Hershberger <joe.hershberger@gmail.com>
2016-03-31net: phy: Optionally force master mode for RTL PHYMichael Haas
This patch introduces CONFIG_RTL8211X_PHY_FORCE_MASTER. If this define is set, RTL8211x PHYs (except for the RTL8211F) will have their 1000BASE-T master/slave autonegotiation disabled and forced to master mode. This is helpful for PHYs like the RTL8211C which produce unstable links in slave mode. Such problems have been found on the A20-Olimex-SOM-EVB and A20-OLinuXino-Lime2. There is no proper way to identify affected PHYs in software as the RTL8211C shares its UID with the RTL8211B. Thus, this fix requires the introduction of an #ifdef. CC: fradav@gmail.com CC: merker@debian.org CC: hdegoede@redhat.com CC: ijc@hellion.org.uk CC: joe.hershberger@ni.com Signed-off-by: Michael Haas <haas@computerlinguist.org> Tested-by: Karsten Merker <merker@debian.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-03-22net: Move CONFIG_RTL8169 to KconfigBin Meng
Introduce CONFIG_RTL8169 in Kconfig and move over boards' defconfig to use that. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Stephen Warren <swaren@nvidia.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-03-22net: Move CONFIG_RTL8139 to KconfigBin Meng
Introduce CONFIG_RTL8139 in Kconfig and move over boards' defconfig to use that. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> [trini: Fixup MPC8641HPCN* and r2dplus configs] Signed-off-by: Tom Rini <trini@konsulko.com>
2016-02-01drivers: net: Add ethernet driver for Microchip PIC32.Purna Chandra Mandal
This driver implements MAC and MII layer of the ethernet controller. Network data transfer is handled by controller internal DMA engine. Ethernet controller is configurable through device-tree file. Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
2016-01-27net: emaclite: Move emaclite to KconfigMichal Simek
Add PHYLIB and MII dependencies and enable it by default for Microblaze. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-27net: Add axi emac to KconfigMichal Simek
Also add dependency on PHYLIB and MII which is required. Clean PHYLIB dependency from the driver too. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-12-22net: eth_designware: select PHYLIB in KconfigThomas Chou
Select PHYLIB in drivers/net/Kconfig. And remove CONFIG_PHYLIB from legacy board header files. This fixed the warnings when both ALTERA_TSE and ETH_DESIGNWARE are selected. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Reported-by: Pavel Machek <pavel@denx.de> Acked-by: Chin Liang See <clsee@altera.com> Acked-by: Pavel Machek <pavel@denx.de> Tested-by: Pavel Machek <pavel@denx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2015-12-18net: gem: Add driver dependencies to PHYLIBMichal Simek
Clear driver dependecies via Kconfig. Remove PHYLIB dependency from the driver. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2015-12-18net: gem: Fix typo in Kconfig entryMichal Simek
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-12-07net: gem: Move gem to KconfigMichal Simek
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2015-10-23net: convert altera_tse to driver model and phylibThomas Chou
Convert altera_tse to driver model and phylib. Signed-off-by: Thomas Chou <thomas@wytron.com.tw> Reviewed-by: Marek Vasut <marex@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
2015-09-09net: pch_gbe: Add Kconfig optionBin Meng
Add Kconfig option in preparation for moving board to use Kconfig. Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
2015-08-21net: e1000: Add Kconfig optionsSimon Glass
Add Kconfig options in preparation for moving boards to use Kconfig. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-06-25Move defaults from config_cmd_default.h to KconfigJoe Hershberger
This sets the default commands Kconfig to match include/config_cmd_default.h commands in the common/Kconfig and removes them from include/configs. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> [trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates] Signed-off-by: Tom Rini <trini@konsulko.com>
2015-04-18Kconfig: Move CONFIG_DESIGNWARE_ETH to KconfigSimon Glass
Move this to Kconfig and clean up board config files that use it. Also rename it to CONFIG_ETH_DESIGNWARE to fit with the naming that exists in drivers/net/Kconfig. Signed-off-by: Simon Glass <sjg@chromium.org> Version 1: Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2015-04-18sandbox: eth: Add a bridge to a real network for sandboxJoe Hershberger
Implement a bridge between U-Boot's network stack and Linux's raw packet API allowing the sandbox to send and receive packets using the host machine's network interface. This raw Ethernet API requires elevated privileges. You can either run as root, or you can add the capability needed like so: sudo /sbin/setcap "CAP_NET_RAW+ep" /path/to/u-boot Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2015-04-18sandbox: eth: Add network support to sandboxJoe Hershberger
Add basic network support to sandbox which includes a network driver. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2015-04-18dm: eth: Add basic driver model support to Ethernet stackJoe Hershberger
First just add support for MAC drivers. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2014-09-24kconfig: add blank Kconfig filesMasahiro Yamada
This would be useful to start moving various config options. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
generated by cgit (git 2.34.1) at 2024-12-24 20:42:17 +0000