| Age | Commit message (Collapse) | Author |
|---|
|
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This reverts commit 5d3a21df6694ebd66d5c34c9d62a26edc7456fc7, reversing
changes made to 56d37f1c564107e27d873181d838571b7d7860e7.
Unfortunately this is causing CI failures:
https://travis-ci.org/github/trini/u-boot/jobs/711313649
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
When you enable CONFIG_OF_LIVE, you will end up with a lot of
conversions.
To generate this commit, I used coccinelle excluding drivers/core/,
include/dm/, and test/
The semantic patch that makes this change is as follows:
<smpl>
@@
expression dev;
@@
-devfdt_get_addr(dev)
+dev_read_addr(dev)
</smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The H6 EMAC is very similar to the H3 variant, except that it uses the
same pinmux as R40. Add support for it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
While the R40 uses a different register for EMAC clock configuration
than other chips, the register has a very similar layout. Reuse the
existing bitfield definitions in this file, since they match.
This allows the driver to compile on the H6 platform, where the
CCM_GMAC_CTRL definitions are not present.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this uncommon header out of the common header.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this header out of the common header.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
At present if CONFIG_SPL_GPIO_SUPPORT is enabled then the GPIO uclass
is included in SPL/TPL without any control for boards. Some boards may
want to disable this to reduce code size where GPIOs are not needed in
SPL or TPL.
Add a new Kconfig option to permit this. Default it to 'y' so that
existing boards work correctly.
Change existing uses of CONFIG_DM_GPIO to CONFIG_IS_ENABLED(DM_GPIO) to
preserve the current behaviour. Also update the 74x164 GPIO driver since
it cannot build with SPL.
This allows us to remove the hacks in config_uncmd_spl.h and
Makefile.uncmd_spl (eventually those files should be removed).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
These functions are CPU-related and do not use driver model. Move them to
cpu_func.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
H3/H5 can either use the internal phy or an external one.
Before getting clock and resets for the internal phy,
test that we are using it because otherwise it break emac
when using an external phy.
Tested-on: OrangePi PC2 (H5)
Fixes: 2348453c41 (net: sun8i_emac: Add EPHY CLK and RESET support)
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Add EPHY CLK and RESET support for sun8i_emac driver to
enable EPHY TX clock and EPHY reset pins via CLK and RESET
framework.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Lothar Felten <lothar.felten@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Add CLK and RESET support for sun8i_emac driver to
enable TX clock and reset pins via CLK and RESET
framework.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Lothar Felten <lothar.felten@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Unlike other Allwinner SoC's R40 GMAC clock control register
is locate in CCU, but rest located via syscon itself. Since
the phandle property for current code look for 'syscon' and
it will grab the respective ccu or syscon base address based
on DT property defined in respective SoC dtsi.
So, use the existing 'syscon' code even for R40 for retrieving
GMAC clock via CCU and update the register directly in
sun8i_emac_set_syscon instead of writing it separately using
ccm base.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Lothar Felten <lothar.felten@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Some boards have the EMAC TX/RX lanes wired with a different length with
the clock lane, which can be workarounded by setting a TX/RX delay in
the EMAC.
This kind of delays are already defined in the newest device tree
binding of dwmac-sun8i, which has already entered linux-next.
Add support for setting these delays.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
Add support for the GMAC found in the Allwinner R40/V40 SoC.
The R40 GMAC interface is not controlled by the syscon register but
has a separate configuration register in the CCU.
The clock gate and reset bits are in a different register compared
to the other SoCs supported by this driver.
The driver uses the -gmac suffix for the R40 because the R40 also
has a different 100 MBit MAC (EMAC).
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
|
|
Use driver data->variant information to select device specific
pin mux and phy clock settings.
Suggested by Jagan Teki
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
|
|
If the variant is not set and therefore NULL, do not attempt to print
the variant.
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The original DT binding used by U-Boot's sun8i-emac driver was not really
agreed upon, and deviated from the "official" binding now used by the
kernel. Since now all U-Boot users have been converted to the new
binding, we can remove support for the old DT nodes from the driver.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
The Ethernet MAC used in newer Allwinner SoCs (H3, A64, H5) got an
upstream Linux driver in v4.15.
This one uses a slightly different binding from the original one used
by the U-Boot driver.
The differences to the old binding are:
- The "syscon" address is held in a separate node, referenced via a
phandle in the "syscon" property.
- The reference to the PHY is held in a property called "phy-handle",
not "phy".
- The PHY register is at offset 0x30 in the syscon device, not at 0.
- The internal PHY is activated when the node, which phy-handle points
to, is a child node of an "allwinner,sun8i-h3-mdio-internal" node.
Teach the U-Boot driver how to find its resources in a "new-style" DT,
so that we can use a Linux kernel compatible DT for U-Boot as well.
This keeps support for the old binding for now, to allow a smooth
transition.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
The Linux kernel driver for the Allwinner pin controller gained support
for generic properties, which are now also used in the DTs.
The sun8i-emac Ethernet driver for new Allwinner MACs reads the pins from
the DT, but so far only supported the old binding.
Update the parsing routine to cope with both the old and new bindings,
so that the newer DTs can be used with U-Boot and its Ethernet driver.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
The previous code tried to update the PHY parameters without waiting for
autonegotiation to complete. This caused wrong values to be written to
the EMAC in sun8i_adjust_link(). As a result, any commands that called
eth_start() before autonegotiation completed would find the network
nonfunctional. Fix this by using the correct function to start up the
PHY.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
Only the H3/H5 SoCs have an internal PHY and its related clock and
reset controls.
Use an #ifdef to guard the internal PHY control code block so it
can be built for other SoCs, such as the A83T or A64.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing functions to avoid confusion.
In the end we will have:
1. dev_read_addr...() - works on devices, supports flat/live tree
2. devfdt_get_addr...() - current functions, flat tree only
3. of_get_address() etc. - new functions, live tree only
All drivers will be written to use 1. That function will in turn call
either 2 or 3 depending on whether the flat or live tree is in use.
Note this involves changing some dead code - the imx_lpi2c.c file.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This ports the support for configuring a GPIO for resetting the
Ethernet PHY (incl. such details as the reset polarity and
pulse-length) from the Designware driver.
X-AffectedPlatforms: A64-uQ7
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
The Allwinner H5 is very close to the H3 SoC, but has ARMv8 cores.
To allow sharing the clocks, GPIO and driver code easily, create an
architecture agnostic MACH_SUNXI_H3_H5 Kconfig symbol.
Rename the existing symbol to MACH_SUNXI_H3_H5 where code is shared and
let it be selected by a new shared Kconfig option.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
To send a parametrized command to the PHY over MDIO, we should write
the data first, the trigger the execution by the command register
write. Fix the access pattern in our MDIO write routine.
Apparently this doesn't really matter with the Realtek PHY on the
Pine64, but other PHYs (which require more setup) will choke on
the wrong order.
[Andre: add commit message]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jagan Teki <jagan@openedev.com>
|
|
Commit b02e4044ff8e ("libfdt: Bring in upstream stringlist
functions") broke codying style in some places especially
by inserting an extra whitespace before fdt_stringlist_count().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
These have now landed upstream. The naming is different and in one case the
function signature has changed. Update the code to match.
This applies the following upstream commits by
Thierry Reding <treding@nvidia.com> :
604e61e fdt: Add functions to retrieve strings
8702bd1 fdt: Add a function to get the index of a string
2218387 fdt: Add a function to count strings
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This fixes the following CACHE warnings when using sun8i_emac:
=> dhcp
BOOTP broadcast 1
BOOTP broadcast 2
CACHE: Misaligned operation at range [7bf594a8, 7bf59628]
BOOTP broadcast 3
CACHE: Misaligned operation at range [7bf59c90, 7bf59e10]
CACHE: Misaligned operation at range [7bf5a478, 7bf5a5f8]
DHCP client bound to address 10.42.43.80 (1009 ms)
Note this commit also changes the max rx size from 2024 to 2044,
matching what the kernel driver uses.
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Corentin LABBE <clabbe.montjoie@gmail.com>
Cc: Amit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
In sun8i_emac_board_setup, the driver partially configures the syscon
register for H3 EPHY. However, the settings are incomplete, and
completely unusable. The correct settings are later set in
sun8i_emac_set_syscon, but the incorrect CLK_SEL setting persists.
It is incorrect to use CLK_SEL to select 25 MHz, as the SoC does not
have a 25 MHz clock the EPHY can use.
This patch removes the setting of the syscon register in board_setup,
and also moves set_syscon above mdio_init. While mdio_init does not
access the PHY, it is better to have the PHY parameters setup before
the MDIO bus is registered.
Fixes: a29710c525ff ("net: Add EMAC driver for H3/A83T/A64 SoCs.")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The sun8i_emac driver erroneously configures the AHB2 clock when it
assumes it is configuring the AXI gates, which is not even documented
or ever appeared in either the WiP kernel driver or Allwinner's original
driver.
As a result, AHB2 clock mux is set to an invalid setting, making the
EPHY unusable.
Fixes: a29710c525ff ("net: Add EMAC driver for H3/A83T/A64 SoCs.")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
This patch add EMAC driver support for H3/A83T/A64 SoCs.
Tested on Pine64(A64-External PHY) and Orangepipc(H3-Internal PHY).
BIG Thanks to Andre for providing some of the DT code.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
