summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)Author
2018-03-22drivers: net: cpsw: remove superfluous assignment.Heinrich Schuchardt
In int ret = A; ret = B; the first assignment has not effect. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-22net/phy/cortina: Add No firmware upload optionPriyanka Jain
Current Cortina phy driver assumes that firmware upload is required during initialization and is dependent on presence of corresponding macros like CONFIG_CORTINA_FW_ADDR for compilation. But Cortina phy has provision to store phy firmware in attached dedicated EEPROM. And boards designed with such EEPROM does not require firmware upload. Add CORTINA_NO_FW_UPLOAD option in cortina.c to support such boards. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-22net/phy/cortina.c: Update get_phy_id implementationPriyanka Jain
Update get_phy_id() implementation in cortina.c to check for Cortina_phy by comparing device phy_id with cortina phy_id instead of relying on presence of CORTINA macros. This will allow get_phy_id to work with non-cortina phy devices which might have same phy address as Cortina device but on different bus. Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-22configs: ls1012a: add pfe configuration for LS1012ACalvin Johnson
Add configurations for PFE. Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com> Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-22drivers: net: pfe_eth: provide pfe commandsCalvin Johnson
pfe_command provides command line support for several features that support pfe, like starting or stopping the pfe, checking the health of the processor engines and checking status of different units inside pfe. Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com> Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-22drivers: net: pfe_eth: LS1012A PFE driver introductionCalvin Johnson
This patch adds PFE driver to U-Boot Following are the main driver files:- pfe_hw.c: provides low level helper functions to initialize PFE internal processor engines and other hardware blocks pfe_driver.c: provides initialization functions and packet send and receive functions pfe_eth.c: provides high level gemac initialization functions pfe_firmware.c: provides functions to load firmware into PFE internal processor engines. pfe_mdio.c: provides functions to initialize phy and mdio. Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com> Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-22drivers: net: phy: Fix aquantia compilation with DMCalvin Johnson
With CONFIG_DM_ETH enabled, aquantia driver compilation fails with below error. This patch fixes the issue by including dm.h. drivers/net/phy/aquantia.c: In function ‘aquantia_startup’: drivers/net/phy/aquantia.c:73:21: error: dereferencing pointer to incomplete type ‘struct udevice’ phydev->dev->name); ^~ Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-22net: mvpp2x: add check after callocHeinrich Schuchardt
After allocating plat the pointer is checked. Afterwards name is allocated and not checked. Add the missing check to avoid a possible NULL dereference. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-22net: phy: Add PHY_RTL8211E_PINE64_GIGABIT_FIX for realtek physkevans@FreeBSD.org
Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off on the PHY, as well as flipping some magical undocumented bits. The magic number comes from the Pine64 engineering team, presumably as a proxy from Realtek. This configuration fixes the throughput on some Pine64 models. Packet loss of up to 60-70% has been observed without this. Signed-off-by: Kyle Evans <kevans@FreeBSD.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-13Move CONFIG_PHY_ADDR to KconfigStefan Mavrodiev
CONFIG_PHY_ADDR is used for old-style configuration. This makes impossible changing the PHY address, if multiple boards share a same config header file (for example include/configs/sunxi-common.h). Moving this to Kconfig helps overcoming this issue. It's defined as entry inside PHYLIB section. After the implemention, moveconfig was run. The issues are: - edb9315a - CONFIG_PHYLIB is not enabled. Entry is deleted. - ds414 - CONFIG_PHYLIB is in incompatible format: { 0x1, 0x0 }. This entry is also deleted. - devkit3250 - The PHY_ADDR is in hex format (0x1F). Manually CONFIG_PHY_ADDR=31 is added in the defconfig. After the changes the suspicious defconfigs passes building. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> [jagan: rebased on master] Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-03-13net: sun8i_emac: Fix PHY initializationSamuel Holland
The previous code tried to update the PHY parameters without waiting for autonegotiation to complete. This caused wrong values to be written to the EMAC in sun8i_adjust_link(). As a result, any commands that called eth_start() before autonegotiation completed would find the network nonfunctional. Fix this by using the correct function to start up the PHY. Signed-off-by: Samuel Holland <samuel@sholland.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-03-05Merge git://git.denx.de/u-boot-shTom Rini
2018-03-05libfdt: move headers to <linux/libfdt.h> and <linux/libfdt_env.h>Masahiro Yamada
Thomas reported U-Boot failed to build host tools if libfdt-devel package is installed because tools include libfdt headers from /usr/include/ instead of using internal ones. This commit moves the header code: include/libfdt.h -> include/linux/libfdt.h include/libfdt_env.h -> include/linux/libfdt_env.h and replaces include directives: #include <libfdt.h> -> #include <linux/libfdt.h> #include <libfdt_env.h> -> #include <linux/libfdt_env.h> Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2018-03-05net: ravb: Add R8A77965 M3N entriesMarek Vasut
Add entries for the R8A77965 M3N SoC. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Joe Hershberger <joe.hershberger@ni.com>
2018-02-26net: phy: smsc: Add SMSC LAN8741 supportArno Steffens
Signed-off-by: Arno Steffens <star@gmx.li> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-02-26net: e1000: Fix e1000_igb semaphore handlingBernhard Messerklinger
Fix commit f1bcad22dd19 ("net: e1000: add support for writing to EEPROM"). Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-02-26NET: designware: fix clock enableEugeniy Paltsev
After commit ba1f966725223 ("net: designware: add clock support") we got NET broken on axs101 and axs103 platforms. Some clock don't support gating so their clock drivers don't implement .enable/.disable callbacks. In such case clk_enable returns -ENOSYS. Also some clock drivers implement .enable/.disable callbacks not for all clock IDs and return -ENOSYS (or -ENOTSUPP) for others. If we have such clock in 'clocks' list of designware ethernet controller node we fail to probe designware ethernet. Fix it. Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-02-26phy: Fix style violationsMario Six
Fix some style violations in the generic PHY management code. Acked-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-02-26net: phy: marvell 88e151x: Fix handling of bare RGMII interface typeMario Six
Commit 68e6ecadc551 ("net: phy: marvell 88e151x: Fix handling of RGMII interface types") fixed the initialization of 88e151x phys, but made it so that interfaces of type PHY_INTERFACE_MODE_RGMII had both RX and TX delay bits cleared. The default (like in m88e1111s_config) is to have both bits set. Hence, this patch changes the behavior in the PHY_INTERFACE_MODE_RGMII case so that both bits are set. Signed-off-by: Mario Six <mario.six@gdsys.cc> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-02-26net: phy: marvell: Fix style violationsMario Six
Fix some style violations (mostly wrong indentions) in the Marvell PHY driver. Acked-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-02-26net: tsec: Make live-tree compatibleMario Six
Make the tsec ethernet driver compatible with a live device tree. Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-02-26net: tsec: Fix memory leak in error pathMario Six
tsec_initialize allocates a private driver structure using malloc. Should the memory allocation of this private structure fail, the function execution is aborted with a return 0, but the previously allocated device structure is never freed, hence leaked. Free the device structure in the error case. Signed-off-by: Mario Six <mario.six@gdsys.cc> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-02-26net: tsec: Fix style violationsMario Six
Signed-off-by: Mario Six <mario.six@gdsys.cc> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-02-23net: Remove Xilinx ll_temac driverMichal Simek
ll_temac driver was used by Xilinx Microblaze big endian and Xilinx ppc405/ppc440 SoCs. ppc support was removed by: "powerpc: remove 4xx support" (sha1: 98f705c9cefdfdba62c069821bbba10273a0a8ed) and Microblaze BE is not tested for a long time that's why this driver can be removed because none is going to updated it to DM anyway. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-02-18net: sh_eth: Fix DT base address fetchingMarek Vasut
Drop the whole map/unmap_physmem stuff and just use the address already obtained from DT in ofdata_to_platdata(), instead of repeating that, wrongly, in probe. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Joe Hershberger <joe.hershberger@ni.com>
2018-02-18net: sh_eth: Fix checkpatch warningMarek Vasut
Fix minor checkpatch warning about udelay(3000) being too long and should be replaced by mdelay(3). Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Joe Hershberger <joe.hershberger@ni.com>
2018-02-18net: sh_eth: Return directly from sh_eth_recv_startMarek Vasut
Drop the len variable, it's useless. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Joe Hershberger <joe.hershberger@ni.com>
2018-02-18net: sh_eth: Zap port variableMarek Vasut
Inline this variable which is quite useless. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Joe Hershberger <joe.hershberger@ni.com>
2018-02-16net: ravb: Initialize PHY in probe() onceMarek Vasut
Reset and initialize the PHY once in the probe() function rather than doing it over and over again is start() function. This requires us to keep the clock enabled while the driver is in use. This significantly reduces the time between transfers as the PHY doesn't have to restart autonegotiation between transfers, which takes forever. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Geert Uytterhoeven <geert+renesas@glider.be> Cc: Joe Hershberger <joe.hershberger@ni.com>
2018-02-08Kconfig: net: phylib: Phylib should depends on NETMichal Simek
There is no value to enable phylib without networking support. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-02-04net: e1000: implement eth_write_hwaddrHannu Lounento
Implement programming MAC address to the hardware, i.e. external flash seen as EEPROM. MAC address is only written if it differs from what is already stored in flash or if reading the current MAC address fails. Signed-off-by: Hannu Lounento <hannu.lounento@ge.com> CC: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
2018-02-04net: e1000: split e1000_read_mac_addrHannu Lounento
Split the implementation of e1000_read_mac_addr into eeprom and register versions called by e1000_read_mac_addr. This allows for calling e1000_read_mac_addr when MAC address is needed with no constraints where it is read from, and for calling the register and, especially, the eeprom version directly in order to specify where to read the address from. Signed-off-by: Hannu Lounento <hannu.lounento@ge.com> CC: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
2018-02-04net: e1000: add support for writing to EEPROMHannu Lounento
Port functions for writing to EEPROM, updating the checksum and committing data to flash from the Linux kernel igb driver. Functions were ported from Linux 4.8-rc2 (694d0d0bb20). Signed-off-by: Hannu Lounento <hannu.lounento@ge.com> CC: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk> Reviewed-by: Stefano Babic <sbabic@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
2018-02-04net: fec: fix build warnings for 64bits supportYe Li
When building for 64bits system, we get some warnings about type cast between pointer and integer. This patch eliminates the warnings by using ulong/long type which is 32bits on 32bits system or 64bits on 64bits system. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-02-04net: fec: do not access reserved register for i.MX8MPeng Fan
The MIB RAM and FIFO receive start register does not exist on i.MX8M. Accessing these register will cause system hang. Signed-off-by: Peng Fan <peng.fan@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Stefano Babic <sbabic@denx.de> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2018-01-31Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
2018-01-30driver: fsl-mc: Perform fsl-mc fdt fixup for lazyapply dplYogesh Gaur
For for case of lazyapply method, API fdt_fixup_board_enet() gets invoked before DPL being deployed. This leads to an issue that fsl-mc fdt fixup status marked as fail and dprc driver didn't get registered in linux boot. Fixes this issue by calling fdt_fixup_board_enet() for case when DPL is deployed successfully in lazyapply method. Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-29mvpp2: Fix warning over 32bit vs 64bit targetsTom Rini
When we have a driver that is used on both 32bit and 64bit targets and we are talking about address space we cannot use u64 nor u32 and instead need to use phys_addr_t. Fixes: 377883f16d36 ("net: mvpp2x: fix phy connected to wrong mdio issue") Cc: Stefan Chulski <stefanc@marvell.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
2018-01-28net: gmac_rockchip: Add support for the RK3228 GMACDavid Wu
The GMAC in the RK3228 once again is identical to the incarnation in the RK3288 and the RK3399, except for where some of the configuration and control registers are located in the GRF. This adds the RK3368-specific logic necessary to reuse this driver. Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-01-28net: gmac_rockchip: Add rk3328 gmac supportDavid Wu
The GMAC2IO in the RK3328 once again is identical to the incarnation in the RK3288 and the RK3399, except for where some of the configuration and control registers are located in the GRF. This adds the RK3328-specific logic necessary to reuse this driver. Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-01-28net: gmac_rockchip: Add support for the RV1108 GMACDavid Wu
The rv1108 GMAC only support rmii interface, so need to add the set_rmii() ops. Use the phy current interface to set rmii or rgmii ops. At the same time, need to set the mac clock rate of rmii with 50M, the clock rate of rgmii with 125M. Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-01-27Merge branch 'rmobile-mx' of git://git.denx.de/u-boot-shTom Rini
2018-01-27net: sh_eth: Add DM and DT supportMarek Vasut
Add DM capable code into the SH ethernet driver and support probing both from DT and pdata. The legacy non-DM, non-DT support is retained as there are still systems in the tree which are not DM or DT capable. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Joe Hershberger <joe.hershberger@ni.com>
2018-01-27net: sh_eth: Clump legacy functions togetherMarek Vasut
Move the legacy functions around, so that they can be wrapped in a massive ifdef CONFIG_DM_ETH once DM support is added. No functional change. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Joe Hershberger <joe.hershberger@ni.com>
2018-01-27net: sh_eth: Split sh_eth_initMarek Vasut
Split sh_eth_init() function into smaller chunks, which can be called from both DM and non-DM code while handling the specifics of both configurations. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Joe Hershberger <joe.hershberger@ni.com>
2018-01-27net: sh_eth: Separate out MAC address programmingMarek Vasut
Pull out the code for writing MAC address into the NIC into a separate function, so it can be reused by both DM and non-DM code. This is done in preparation for DM support, which handles MAC address programming separately. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Joe Hershberger <joe.hershberger@ni.com>
2018-01-27net: sh_eth: Split sh_eth_recvMarek Vasut
Split sh_eth_recv into two functions, one which checks whether a packet was received and one which handles the received packet. This is done in preparation for DM support, which handles these two parts separately. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Joe Hershberger <joe.hershberger@ni.com>
2018-01-27net: sh_eth: Pass sh_eth_dev aroundMarek Vasut
Pass sh_eth_dev structure around instead of eth_device, since the later is specific to the legacy networking support. This change is done in preparation for the DM addition. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Joe Hershberger <joe.hershberger@ni.com>
2018-01-27net: sh_eth: Unify CONFIG_R8A779[01234] as CONFIG_RCAR_GEN2Marek Vasut
Use the common RCAR_GEN2 config option instead of enumerating each SoC and having a lengthy ifdef clause. No functional change. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Joe Hershberger <joe.hershberger@ni.com>
2018-01-27net: ravb: staticize ravb_startMarek Vasut
Cosmetic fix, make ravb_start() static. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Joe Hershberger <joe.hershberger@ni.com>
generated by cgit (git 2.34.1) at 2024-12-25 01:40:30 +0000