summaryrefslogtreecommitdiff
path: root/drivers/net
AgeCommit message (Collapse)Author
2018-06-13mvebu: neta: align DMA buffersJon Nettleton
This makes sure the DMA buffers are properly aligned for the hardware. Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Jon Nettleton <jon@solid-run.com> Signed-off-by: Baruch Siach <baruch@tkos.co.il> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13net: add Socionext AVE ethernet driver supportKunihiko Hayashi
Add driver for Socionext AVE ethernet controller that includes MAC and MDIO bus supporting RGMII/RMII modes. The driver behaves the ethernet driver model (DM_ETH) with devicetree. Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13drivers/net/vsc9953: Initialize action RAM in VCAP complexRadu Bulie
VCAP tables must be initialized even if no advanced classification is used. If no initialization is performed, then ECC error will be observed by the user when the first packet enters the l2switch. The error is marked in MPIC_EISR0 -bit 29 which means - Internal RAM multi-bit ECC error. This patch fixes the aforementioned ECC error by performing the initialization of VCAP tables. Signed-off-by: Radu Bulie <radu-andrei.bulie@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13net: cpsw: ti: Reap completed packets before stopping interfaceAlex Kiernan
If you send a final packet just before stopping the interface (e.g. a final ACK as part of the UDP fastboot protocol), then that packet isn't reliably delivered onto the wire. Reap packets prior to stopping the interface to ensure any which are in-flight make it out. Also remove buffer and len from the call to cpdma_process() as we weren't using them on their return. Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13net/phy/cortina: Add support for CS4223 PHYVicentiu Galanopulo
Add support for Cortina CS4223 10G PHY - As per the CS4223 specs, an EEPROM module is connected to the PHY. At startup the PHY reads the firmware line and tries to load the firmware into the internal memory. - This driver reads the EEPROM status and checks if firmware has been loaded Signed-off-by: Vicentiu Galanopulo <vicentiu.galanopulo@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13net: sunxi: Correct MAC address register orderJoe Hershberger
Put the enetaddr data in the same order as it was before the change in commit ace1520cb5fc ("net: sunxi-emac: Write HW address via function") Reported-by: Udo Maslo <u.maslo@web.de> Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-13tsec: Fix reading phy registers from DTMario Six
Bus translations should be applied when reading the address of the sgmii phy registers from the DT. Use ofnode_get_addr_index instead of the plain ofnode_read_u32_default to fix this. Signed-off-by: Mario Six <mario.six@gdsys.cc> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-06-11LS1012AFRWY: Add Secure Boot supportVinitha V Pillai
Added the following: 1. defconfig for LS1012AFRWY Secure boot 2. PfE Validation support Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-06-02Merge branch 'master' of git://git.denx.de/u-boot-shTom Rini
2018-06-01net: ravb: Add R8A77990 E3 compatibleMarek Vasut
Add new compatible to the Ethernet AVB driver for R8A77990 E3 SoC. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2018-05-29net: ftmac100: Fix compiler warningRick Chen
Fix warnings as below when compile in 64-bit. warning: cast from pointer to integer of different size [-Wpointer-to-int-cast] Signed-off-by: Rick Chen <rick@andestech.com> Signed-off-by: Rick Chen <rickchen36@gmail.com> Cc: Greentime Hu <green.hu@gmail.com>
2018-05-23net: Drop CONFIG_TSI108_ETHTuomas Tynkkynen
Last user of this driver went away in June 2015 in commit d928664f4101e24 ("powerpc: 74xx_7xx: remove 74xx_7xx cpu support") Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-05-17net: MVGBE don't automatically select PHYLIBChris Packham
When Kconfig support was added for MVGBE it included automatically selected PHYLIB support. But MVGBE does not need PHYLIB it will build fine without it. Commit ed52ea507f12 ("net: add Kconfig for MVGBE") should have been a no-op in terms of build size but because of the selecting PHYLIB the openrd configs increased in size. Remove the automatic selection of PHYLIB, boards that need it will have already enabled it in their config header file. Fixes: commit ed52ea507f12 ("net: add Kconfig for MVGBE") Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-14net: add Kconfig for MVGBEChris Packham
Add Kconfig for MVGBE and update boards to select this. Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de>
2018-05-14net: mvgbe: remove CONFIG_DOVEChris Packham
Nothing defines CONFIG_DOVE so remove the code that uses it. Signed-off-by: Chris Packham <judge.packham@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-05-14net: mvneta: Fix fault when wrong device treeMarek Behún
The driver does not check id phy_connect failed (for example on wrong property name in device tree). In such a case a fault occurs and the CPU is restarted. Signed-off-by: Marek Behun <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2018-05-11Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
2018-05-10SPDX: Convert a few files that were missed beforeTom Rini
As part of the main conversion a few files were missed. These files had additional whitespace after the '*' and before the SPDX tag and my previous regex was too strict. This time I did a grep for all SPDX tags and then filtered out anything that matched the correct styles. Fixes: 83d290c56fab ("SPDX: Convert all of our single license tags to Linux Kernel style") Reported-by: Heinrich Schuchardt <xypron.debian@gmx.de> Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-09driver: net: fsl-mc: updated copyright infoYogesh Gaur
Updated copyright info for the issues reported after running check-legal test. Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2018-05-07SPDX: Convert all of our single license tags to Linux Kernel styleTom Rini
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-30Merge git://git.denx.de/u-boot-imxTom Rini
2018-04-27Remove unnecessary instances of DECLARE_GLOBAL_DATA_PTRTom Rini
We have a large number of places where while we historically referenced gd in the code we no longer do, as well as cases where the code added that line "just in case" during development and never dropped it. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-27Convert CONFIG_SPI to KconfigAdam Ford
This converts the following to Kconfig: CONFIG_SPI This partly involves updating code that assumes that CONFIG_SPI implies things that are specific to the MPC8xx SPI driver. For now, just update the CONFIG tests. This also involves reworking the default for CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a reasonable default, as it does not cause any compile failures. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-26dts: dm: fec: imx53: Provide proper compatible string for imx53 fec driverLukasz Majewski
After this change the DM FEC ETH driver can be also reused on some imx53 devices. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-04-26eth: dm: fec: Change FEC PHY mask setting from CONFIG_PHYLIB to ↵Lukasz Majewski
CONFIG_FEC_MXC_PHYADDR Without this commit we do have an explicit dependency on CONFIG_PHYLIB when one wants to set PHY ADDR on a iMX board (FEC + driver model). This shall be changed to CONFIG_FEC_MXC_PHYADDR, as only when we do have it set, we shall mask out other devices. As a side effect, when CONFIG_FEC_MXC_PHYADDR is not set, we scan PHY bus for connected PHY devices. Signed-off-by: Lukasz Majewski <lukma@denx.de>
2018-04-13net: phy: Don't limit phy addresses by defaultJoe Hershberger
Some boards expect to find more than one phy while other boards are old and need to be limited to a specific phy address. Only limit the phy address for boards that opt in. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2018-04-13net: sh_eth: Add remaining Gen2 DT compatibleMarek Vasut
Add compatible strings for R8A7790, R8A7793 and R8A7794, since the contemporary DTs use those don't have a generic match value. Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org> Cc: Joe Hershberger <joe.hershberger@ni.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-13net: zynq_gem: Use max-speed property from dtSiva Durga Prasad Paladugu
Add support to use max-speed property from dt for determining the supported speed. Use 1000Mbps as default. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-13net: fec: Fix issue in DM probe timeoutYe Li
Since the probe function has changed to reset FEC controller prior than setup PHY. If reset FEC controller timeout, the priv->phydev is not initialized, so can't free it. Signed-off-by: Ye Li <ye.li@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-13net: fex_mxc: add i.MX6UL/SX/SL compatiblePeng Fan
Add i.MX6UL/SX/SL compatible. Signed-off-by: Peng Fan <peng.fan@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-13net: fec: sharing MDIO for two enet controllersPeng Fan
On i.MX6SX, 6UL and 7D, there are two enet controllers each has a MDIO port. But Some boards share one MDIO port for the two enets. So introduce a configuration CONFIG_FEC_MXC_MDIO_BASE to indicate the MDIO port for sharing. In Kconfig, user needs enable CONFIG_FEC_MXC_SHARE_MDIO first to enter the CONFIG_FEC_MXC_MDIO_BASE. To i.MX28, adapt to use the new config Signed-off-by: Peng Fan <peng.fan@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Cc: Fabio Estevam <fabio.estevam@nxp.com>
2018-04-13net: fec: set dev->seq to priv->dev_idPeng Fan
To platforms has two enet interface, using dev->seq could avoid conflict. i.MX6UL/ULL evk board net get the wrong MAC address from fuse, eth1 get MAC0 address, eth0 get MAC1 address from fuse. Set the priv->dev_id to device->seq as the real net interface alias id then .fec_get_hwaddr() read the related MAC address from fuse. Signed-off-by: Peng Fan <peng.fan@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-13net: fec_mxc: simplify fec_get_miibusPeng Fan
No need to provide two prototype for this function. Use ulong for the first parameter, then this function could be shared for DM/non DM case. Signed-off-by: Peng Fan <peng.fan@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-13net: fec_mxc: Fix DM driver issue in recvYe Li
When using ethernet DM driver, the recv interface has a change with non-DM interface, that driver needs to set the packet pointer and provide it to upper layer to process. In fec driver, the fecmxc_recv functions does not handle the packet pointer parameter. This may cause crash in upper layer processing because the packet pointer is not set. This patch allocates a buffer for the packet pointer and free it through free_pkt interface. Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-13net: mvneta: support setting hardware addressMatt Pelland
mvneta already supports setting the MAC address but this was only done internally when some other part of U-Boot tries to actually use the interface. This commit exposes this functionality to the ethernet core code so that the MAC addresses of all interfaces are configured correctly even if they are not used before loading Linux. Signed-off-by: Matt Pelland <mpelland@starry.com> Reviewed-by: Stefan Roese <sr@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-09Merge tag 'xilinx-for-v2018.05-rc2' of git://git.denx.de/u-boot-microblazeTom Rini
Xilinx changes for v2018.05-rc2 - Various DT changes and sync with mainline kernel - Various defconfig updates - Add SPL init for zcu102 revA - Add new zynqmp boards zcu100/zcu104/zcu106/zcu111/zc12XX and zc1751-dc3 - Net fixes - xlnx,phy-type - 64bit axi ethernet support - arasan: Fix nand write issue - fpga fixes - Maintainer file updates
2018-04-09net: phy: xilinx_phy: Read phytype using property xlnx,phy-typeSiva Durga Prasad Paladugu
This patch reads phytype from property "xlnx,phy-type" instead od simply looking for "phy-type". This is to be inline with Linux and also fixes the issue of detecting it wrongly in u-boot. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-09axi: ethernet: Added support for 64 bit addressing for axi-ethernetVipul Kumar
This patch uses writeq() function to enable greater than 32 bit addressing of axi-ethernet for the ZynqMP devices. Signed-off-by: Vipul Kumar <vipulk@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-08net: Move enetaddr env access code to env config instead of net configAlex Kiernan
In order that we can use eth_env_* even when CONFIG_NET isn't set, move these functions to environment code from net code. This fixes failures such as: board/ti/am335x/built-in.o: In function `board_late_init': board/ti/am335x/board.c:752: undefined reference to `eth_env_set_enetaddr' u-boot/board/ti/am335x/board.c:766: undefined reference to `eth_env_set_enetaddr' which caters for use cases such as: commit f411b5cca48f ("board: am335x: Always set eth/eth1addr environment variable") when Ethernet is required in Linux, but not U-Boot. Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
2018-04-08Migrate CONFIG_DRIVER_TI_CPSW to KconfigAlex Kiernan
This converts CONFIG_DRIVER_TI_CPSW to Kconfig Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-04-08treewide: Migrate CONFIG_TSEC_ENET to KconfigMario Six
Migrate the CONFIG_TSEC_ENET option to Kconfig. Signed-off-by: Mario Six <mario.six@gdsys.cc>
2018-04-06powercp: mpc8xx: move commproc.hChristophe Leroy
include/commproc.h is dedicated to the 8xx, rename it cpm_8xx.h and move it into arch/powerpc/include/asm Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
2018-04-06powerpc: mpc8xx: Change CONFIG_8xx to CONFIG_MPC8xxChristophe Leroy
CONFIG_8xx doesn't mean much outside of arch/powerpc/ This patch renames it CONFIG_MPC8xx just like CONFIG_MPC85xx etc ... It also renames 8xx_immap.h to immap_8xx.h to be consistent with other file names. Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
2018-04-04Merge git://git.denx.de/u-boot-sunxiTom Rini
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-04net: sun8i-emac: remove support for old bindingAndre Przywara
The original DT binding used by U-Boot's sun8i-emac driver was not really agreed upon, and deviated from the "official" binding now used by the kernel. Since now all U-Boot users have been converted to the new binding, we can remove support for the old DT nodes from the driver. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-04-04net: sun8i-emac: add support for new EMAC DT bindingAndre Przywara
The Ethernet MAC used in newer Allwinner SoCs (H3, A64, H5) got an upstream Linux driver in v4.15. This one uses a slightly different binding from the original one used by the U-Boot driver. The differences to the old binding are: - The "syscon" address is held in a separate node, referenced via a phandle in the "syscon" property. - The reference to the PHY is held in a property called "phy-handle", not "phy". - The PHY register is at offset 0x30 in the syscon device, not at 0. - The internal PHY is activated when the node, which phy-handle points to, is a child node of an "allwinner,sun8i-h3-mdio-internal" node. Teach the U-Boot driver how to find its resources in a "new-style" DT, so that we can use a Linux kernel compatible DT for U-Boot as well. This keeps support for the old binding for now, to allow a smooth transition. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-04-04net: sun8i-emac: support new pinctrl DT bindingsAndre Przywara
The Linux kernel driver for the Allwinner pin controller gained support for generic properties, which are now also used in the DTs. The sun8i-emac Ethernet driver for new Allwinner MACs reads the pins from the DT, but so far only supported the old binding. Update the parsing routine to cope with both the old and new bindings, so that the newer DTs can be used with U-Boot and its Ethernet driver. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-03-23net: zynq_gem: Dont run any phy detection logic for GMII caseSiva Durga Prasad Paladugu
This patch bypasses phy detection logic for GMII interface and just depend on phy address received from DT. This patch is required as phy detection logic is different for some phys like xilinx phy which can be connected over SGMII and GMII interface. This fixes the issue of ethernet failures when xilinx phy is connected over GMII interface. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-22net: Drop CONFIG_ENC28J60Tuomas Tynkkynen
Last user of this driver went away in October 2014 in commit d58a9451e7339ed4 ("ppc/arm: zap EMK boards"). Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-03-22net: macb: remove superfluous logical constraintHeinrich Schuchardt
In if (a > =0) {...} else (a < 0) {...} the second logical constraint is superfluous. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>