| Age | Commit message (Collapse) | Author |
|---|
|
At present this fails silently which can be confusing since some devices
on the PCI bus may not work correctly. Show a message in this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: add a '\n' in the PCI autoconfig fail message]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
vme8349.h contains two separate boards: The vme8349 itself, and the
caddy2 board. The caddy2 board is chosen by setting certain config
variables. Create a proper config file for the caddy2 board to make
Kconfig migration easier.
Furthermore, simplify the vme8349 and caddy2 configs by keeping only the
options necessary for each board.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
CONFIG_TARGET_VME8349 can replace CONFIG_VME8349. Hence, replace
CONFIG_VME8349 with CONFIG_TARGET_VME8349, and remove CONFIG_VME8349.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
Replace CONFIG_MPC834* with proper CONFIG_ARCH_MPC834* Kconfig options.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
Currently, if we happen to allocate an address requiring 64 bits to a
device only supporting 32-bit BARs, the address eventually gets silently
truncated to 32 bits. Avoid this by adding a new flag to
pciauto_region_allocate() to bail out in such situations.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This patch is to change U-Boot PCI bus assignement compliant with Linux.
It means each PCIe controller's bus number is 0, not the current maximum
PCI bus number, when start to scan this controller.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Fix the following compiler warnings when DEBUG is on.
warning: 'bar_res' may be used uninitialized in this function.
drivers/pci/pci_auto.c:101:21:
if (!enum_only && pciauto_region_allocate(bar_res, bar_size,
^
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This function is only available for compatibility with old code. Avoid
using it in the uclass.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
|
|
For this class it is intended to set up the PCI device, so add a comment to
indicate this. This avoids a coverity warning.
Reported-by: Coverity (CID: 134194)
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
At present we are using legacy functions even in the auto-configuration code
used by driver model. Add a new pci_auto.c version which uses the correct
API.
Create a new pci_internal.h header to hold functions that are used within
the PCI subsystem, but are not exported to other drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This file should not be used with driver model as it has lots of legacy/
compatibility functions. Rename it to make this clear.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
PCI_COMMAND_IO bit must be set for VGA device as it needs to respond
to legacy VGA IO address.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
PCI_HEADER_TYPE register (offset 0x0e) bit 7 is an indicator
for multi-function devices. We should mask it off before using
it as the header type.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
At present the PCI output displays 'Mem' when it allocates memory for a PCI
device, whether it is prefetchable or not. There is a distinction since the
memory comes from separate pools. Use 'Prf' instead of 'Mem' when allocating
prefetchable memory.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This option is not used by any board but appears to still be useful, at least
for testing. With recent commits it does not build, so fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This file does not need its own way of doing debug(). Clean it up to use the
new way.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Commit aec241d "dm: pci: Use the correct hose when configuring devices"
was an attempt to fix pci bridge device configuration, but unfortunately
that does not work 100%. In pciauto_config_devices(), the fix tried to
call pciauto_config_device() with a ctlr_hose which is supposed to be
the root controller hose, however when walking through a pci topology
with 2 or more pci bridges this logic simply fails.
The call chain is: pciauto_config_devices()->pciauto_config_device()
->dm_pci_hose_probe_bus(). Here the call to dm_pci_hose_probe_bus()
does not make any sense as the given hose is not the bridge device's
hose, instead it is either the root controller's hose (case#1: if it
is the 2nd pci bridge), or the bridge's parent bridge's hose (case#2:
if it is the 3rd pci bridge). In both cases the logic is wrong.
For example, for failing case#1 if the bridge device to config has the
same devfn as one of the devices under the root controller, the call
to pci_bus_find_devfn() will return the udevice of that pci device
under the root controller as the bus, but this is wrong as the udevice
is not a bus which does not contain all the necessary bits associated
with the udevice which causes further failures.
To correctly support pci bridge device configuration, we should still
call pciauto_config_device() with the pci bridge's hose directly.
In order to access valid pci region information, we need to refer to
the root controller simply by a call to pci_bus_to_hose(0) and get the
region information there in the pciauto_prescan_setup_bridge(),
pciauto_postscan_setup_bridge() and pciauto_config_device().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
In driver model, each pci bridge device has its own hose structure.
hose->first_busno points to the bridge device's device number, so
we should not substract hose->first_busno before programming the
bridge device's primary/secondary/subordinate bus number registers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Currently PCI expansion ROM address is assigned by a call to
pciauto_setup_rom() outside of the pci auto config process.
This does not work when expansion ROM is on a device behind
PCI bridge where bridge's memory limit register was already
programmed to a value that does not cover the newly assigned
expansion ROM address. To fix this, we should configure the
ROM address during the auto config process.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
The legacy IDE device has a BAR4 (Bus Master Interface BAR) which
needs to be configured.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Remove the '#undef DEBUG' in pci_auto.c so that we can enable debug
message output via '-DDEBUG'.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Add a uclass for PCI controllers and a generic one for PCI devices. Adjust
the 'pci' command and the existing PCI support to work with this new uclass.
Keep most of the compatibility code in a separate file so that it can be
removed one day.
TODO: Add more header file comments to the new parts of pci.h
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
PCI specification allow prefetchable memory to be 32-bit or 64-bit.
PCI express specification states that all memmory bars for prefetchable
memory must be implemented as 64-bit. They all require that 64 bit
prefetchble memory are suported especially when u-boot is ported to
more and more 64bit processors.
Signed-off-by: David Feng <fenghua@phytium.com.cn>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Add code to the generic pci_rom file to access the VGA ROM in PCI space
when needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.
Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Forcibly set hose->pci_prefetch to NULL to make sure it will be setup.
This will help if for any reason callers didn't make sure themselves to
NULL the field.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
|
|
The following commit introduced some warnings associated with using
pci_addr_t instead of a proper 32-bit data type.
commit af778c6d9e2b945ee03cbc53bb976238a3374f33
Author: Andrew Sharp <andywyse6@gmail.com>
Date: Wed Aug 1 12:27:16 2012 +0000
pci: fix errant data types and corresponding access functions
On some platforms pci_addr_t is defined as a 64-bit data type so its not
proper to use with pci_{read,write}_config_dword.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Introduce CONFIG_PCI_ENUM_ONLY variable for platforms that just want a
quick enumberation of the PCI devices, but don't need any setup work done.
This is very beneficial on platforms that have u-boot loaded by another
boot loader which does a more sophisticated job of setup of PCI devices
than u-boot. That way, u-boot can just read what's there and get on
with life. This is what SeaBIOS does.
Signed-off-by: Andrew Sharp <andywyse6@gmail.com>
|
|
I tried to clean up the white space and formatting offenses and
inconsistencies in the generic PCI code that obviously has been around for
some time. Emphasis on large increases in readability and maintainability
and consistency. I omitted the platform/processor specific files in
the drivers/pci directory because I wanted to leave those file to those
that care more about them.
Signed-off-by: Andrew Sharp <andywyse6@gmail.com>
|
|
In a couple of places, unsigned int and pci_config_*_dword were being
used when u16 and _word should be used. Unsigned int was also being
used in a couple of places that should be pci_addr_t.
Signed-off-by: Andrew Sharp <andywyse6@gmail.com>
|
|
As discussed on the list, move "arch/ppc" to "arch/powerpc" to
better match the Linux directory structure.
Please note that this patch also changes the "ppc" target in
MAKEALL to "powerpc" to match this new infrastructure. But "ppc"
is kept as an alias for now, to not break compatibility with
scripts using this name.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Anatolij Gustschin <agust@denx.de>
|
|
This patch adds support for the esd VME8349 board equipped with the
MPC8349. It's a VME PMC carrier board equipped with the Tundra
TSI148 VME-bridge.
Signed-off-by: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
Use the standard lowercase "x" capitalization that other Freescale
architectures use for CPU defines to prevent confusion and errors
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
PCI bus is inherently 64-bit. While not all system require access to
the full 64-bit PCI address range some do. This allows those systems
to enable the full PCI address width via CONFIG_SYS_PCI_64BIT.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Fleming-AFLEMING <afleming@freescale.com>
Acked-by: Wolfgang Denk <wd@denx.de>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Remove test for CONFIG_MPC5200 in drivers/pci/pci_auto.c and define
CONFIG_PCIAUTO_SKIP_HOST_BRIDGE in related board configuration files.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
