| Age | Commit message (Collapse) | Author |
|---|
|
Add a new SERDES driver for TI's AM654x SoC which configures
the SERDES only for PCIe. Support fo USB3 can be added later.
SERDES in am654x has three input clocks (left input, external
reference clock and right input) and two output clocks (left
output and right output) in addition to a PLL mux clock which
the SERDES uses for Clock Multiplier Unit (CMU refclock).
The PLL mux clock can select from one of the three input
clocks. The right output can select between left input and
external reference clock while the left output can select
between the right input and external reference clock.
The driver has support to select PLL mux and left/right output
mux as specified in device tree.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
In preparation for supporting the musb driver, this patch
adds support for the usb phy associated with the musb driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
This adds support for the USB PHYs found in the Amlogic G12A SoC Family.
The USB2 PHY supports Host and/or Peripheral mode, depending on it's position.
The first PHY is only used as Host, but the second supports Dual modes
defined by the USB Control Glue HW in front of the USB Controllers.
The second driver supports USB3 Host mode or PCIE 2.0 mode, depending on
the layout of the board.
Selection is done by the #phy-cells, making the mode static and exclusive.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
This driver is derived from this Linux driver:
linux/drivers/phy/ralink/phy-ralink-usb.c
The driver sets up power and host mode, but also needs to configure PHY
registers for the MT7628 and MT7688.
I removed the reset controller handling for the USB host and device, as
it does not seem to be necessary right now. The soft reset bits for both
devices are enabled by default and testing has shown (with hackish
reset handling added), that USB related commands work identical with
or without the reset handling.
Please note that the resulting USB support is tested only very minimal.
I was able to detect one of my 3 currently available USB sticks.
Perhaps some further work is needed to fully support the EHCI controller
integrated in the MT76x8 SoC.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
This drivers supports the USB2 PHY found on omap5 and dra7 SOCs.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
Add a PHY driver for the R-Car Gen3 which allows configuring
USB OTG PHY on Gen3 into host mode and toggles VBUS in case a
dedicated regulator is present.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Add a PHY driver for the Qualcomm dragonboard 410c which
allows switching on/off and resetting the phy connected
to the EHCI controllers and USBHS controller.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
|
|
Add a PHY driver for the R-Car Gen2 which allows configuring the mux
connected to the EHCI controllers and USBHS controller.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
This patch adds phy tranceiver driver for STM32 USB PHY
Controller (usbphyc) that provides dual port High-Speed
phy for OTG (single port) and EHCI/OHCI host controller
(two ports).
One port of the phy is shared between the two USB controllers
through a UTMI+ switch.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The Amlogic Meson GXL and GXM (simple variant) embeds up to 3 USB2 PHYs
and an USB3 PHY. This patch adds drivers for these for the standard generic
PHY interface and supports the power-on/off calls and set the Host mode by
default.
They are based on the excellent work from Martin Blumenstingl merged in linux.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Signed-off-by: Ãlvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
Signed-off-by: Ãlvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
Signed-off-by: Ãlvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
Signed-off-by: Ãlvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
|
|
This is the generic phy driver for the picoPHY ports
used by USB2/1.1 controllers. It is found on STiH407 SoC
family from STMicroelectronics.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This driver is used to stub PHY operations in a driver (USB, SATA).
This is useful when the 'client' driver (USB, SATA, ...) uses the PHY
framework and there is no actual PHY harwdare to drive.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
This phy is found on omap platforms with sata capabilities.
Except for the part related to the DM and the PHY framework, the code is
basically a copy paste from arch/arm/mach-omap2/pipe3-phy.c
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Those tests check:
- the ability for a phy-user to get a phy based on its name or its index
- the ability of a phy device (provider) to manage multiple ports
- the ability to perform operations on the phy (init,deinit,on,off)
- the behavior of the uclass when optional operations are not implemented
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The PHY framework provides a set of APIs to control a PHY. This API is
derived from the linux version of the generic PHY framework.
Currently the API supports init(), deinit(), power_on, power_off() and
reset(). The framework provides a way to get a reference to a phy from the
device-tree.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
