| Age | Commit message (Collapse) | Author |
|---|
|
Fix the pin-mux values for the MDC, MDIO, MDIO_INTL, PHYRSTL pins.
Fixes: fc9da85c6059 ("pinctrl: uniphier: add Ethernet pin-mux settings")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This is needed to get access to UniPhier System Bus (external bus).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This does not have much impact on behavior, but makes code look more
more like Linux. The use of devm_ioremap() often helps to delete
.remove callbacks entirely.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
SPL does not use all of the devices, so we can save some memory
footprint.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
PH1-LD4 and PH1-sLD8 SoCs have pins that support pin configuration
(pin biasing, drive strength control), but not pin-muxing.
Allow to fill the mux value table with -1 for those pins; pins with
mux value -1 will be skipped in the pin-mux set function. The mux
value type should be changed from "unsigned" to "int" in order to
accommodate -1 as a special case.
[ Linux commit: 363c90e743b50a432a91a211dd8b078d9df446e9 ]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
PH1-LD11 and PH1-LD20 have much pin controlling in common, so I
added a single driver shared between them in the initial commit.
However, the Ethernet pin-mux settings I am going to add are
different with each other, and they may diverge more as the
progress of development. Split it into two dedicated drivers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Currently, the UniPhier pinctrl driver itself is a syscon, but it
turned out much more reasonable to make it a child node of a syscon
because our syscon node consists of a bunch of system configuration
registers, not only pinctrl, but also phy, and misc registers.
It is difficult to split the node. This commit allows to migrate to
the new DT structure.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This SoC does not support NAND CS1. This place-holder is no longer
necessary.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
My mistake in the initial support patch.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
I found many mistakes in the initial version.
Fixes: 8a3328c209d0 ("pinctrl: uniphier: support UniPhier PH1-LD20 pinctrl driver")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The pinmux of PH1-LD11 is almost a subset of that of PH1-LD20
(as far as used in boot-loader), so this commit makes the driver
shared between the two SoCs.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add pin configuration and pinmux support for UniPhier PH1-LD20 SoC.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
