| Age | Commit message (Collapse) | Author |
|---|
|
Add get_pin_mux ops support to display the pin muxing
description of the sandbox_pins[]
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add get_pin_muxing() ops to obtain the pin muxing description
a given pin index.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add get_pin_name ops to obtain a pin name given a
pin index of a specified pin-controller.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add get_pins_count ops to obtain the number of pins
owns by a pin-controller.
On STM32 SoCs bindings, each pin-controller owns
several gpio banks. Each GPIO bank can own up to 16 pins.
To obtain the total pins count, walk through each sub-nodes
(ie GPIO banks) and sum each GPIO banks pins number. For that
in probe() we build a list with each GPIO device reference found.
This list will also be used with future get_pin_muxing and get_pin_name
ops to speed up and optimize walk through all GPIO banks.
As this code is common to all STM32 SoCs, this code is put
under SPL_BUILD compilation flag to avoid to increase SPL code size
for STM32F7 which is limited to 32Ko.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add pinctrl_get_pin_name() and pinctrl_get_pins_count() methods
to obtain pin's name and pin's muxing given a pin reference.
This will be used by the new pinmux command.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add get_pin_muxing() which allows to display the muxing
of a given pin belonging to a pin-controller.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add definition of the POCCTRL register and bits therein to R8A77990 E3
pincontrol driver. This allows the pincontrol driver to configure SDHI
pin voltage according to power-source DT property.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Use fixed 4bit size for generating the DRV register element mask,
not the size of the value, which can be smaller.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Add pinctrl driver for i.MX8. The pads configuration is controlled
by SCU, so need to ask SCU to configure pads through scfw API.
Add pinctrl-scu to invoke sc_pad_set to configure pads.
Add a new flag IMX8_USE_SCU to differentiate i.MX8 from other platforms
which could directly configure pads from Acore side.
Add CONFIG_PINCTRL_IMX8 as the built gate.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Add onewire "w1" groups and pin function for onewire GPIOs in sandbox.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
|
|
Add pinctrl support for broadcom bcm6838 SoC.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
|
|
Following build warning appears when pinctrl-single is built for ARM64:
In file included from drivers/pinctrl/pinctrl-single.c:10:0:
drivers/pinctrl/pinctrl-single.c: In function ‘single_configure_pins’:
./arch/arm/include/asm/io.h:43:28: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
#define __arch_getw(a) (*(volatile unsigned short *)(a))
Fix this by using phys_addr_t for variable reg instead of u32
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
The sh_pfc_{read,write}() must operate on the register address directly
rather than on an offset, fix this to prevent illegal access.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Sync the PFC tables with Linux v4.17.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Sync the PFC tables with Linux v4.17.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
|
|
This patch adds initial pinctrl driver to support for the R8A77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
This follows the style of existion PORT_GP_X macros and
will be used by a follow-up patch for the r8a77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
When the pin control driver selects SD/eMMC function for
a pin group, there is additional configuration to be done
for this case - switch the PHY to work with SDHCI interface.
This patch adds the missing functionality into the pin
control driver.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Evan Wang <xswang@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
For pinctrl driver of mvebu, the compatible strings
supported are defined differently from Linux version.
The patch aligned the compatible string with
Linux 4.17-rc4.
Signed-off-by: Evan Wang <xswang@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Not all the udevice have a available DT node, eg. rksdmmc@ff500000.blk
which add by mmc_bind(), these device do not have/need set pinctrl
state.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
|
|
The pinctrl bindings has changed for Amlogic Meson SoCs since Linux 4.13,
update the pinctrl driver to take this in account.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
These are necessary to optimize the drive-strength of the pins.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This allows our DT to specify drive-strength property.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Currently, the UniPhier pinctrl drivers expose only the pin-group
interface to device tree.
Provide .get_pins_count, .get_pin_name, .pinconf_set hooks to support
pin configuration via 'pins' DT property.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
The #include <linux/bug.h> is here to use BUILD_BUG_ON_ZERO().
By replacing it with <linux/build_bug.h>, we can reduce the number of
headers pulled in.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
dev_err() is more suitable for printing error messages.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Since commit f73cfb4d0dee ("pinctrl: uniphier: simplify input enable
and delete pin arrays"), these data are no longer used in any useful
way. Remove.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Putting zero length array at the end of struct is a common technique
to embed arbitrary length of members. There is no good reason to let
regmap_alloc_count() branch by "if (count <= 1)".
As far as I understood the code, regmap->base is an alias of
regmap->ranges[0].start, but it is not helpful but make the code
just ugly.
Rename regmap_alloc_count() to regmap_alloc() because the _count
suffix seems pointless.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: fixup cpu_info-rcar.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
|
|
Use live dt interface for pinctrl_select_state_full()
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
|
|
This patch corrects below mpp definitions:
- The sdio_sb group is composed of 6 pins and not 5;
- The rgmii group contains pins mpp2[17:6] and not mpp2[19:6];
- Pin of group "pmic0" is mpp1[6] but not mpp1[16];
- Pin of group "pmic1" is mpp1[7] but not mpp1[17];
- A new group "smi" is added in A0 with 2 pins - mpp2[19:18], its
bitmask is bit4;
- Group "pcie1" has 3 pins in A0 - mpp2[5:3], its bit mask is
bit5 | bit9 | bit10 but not bit4;
- Group "ptp" has 3 pins in A0 as Z1, but its bitmask is changed to
bit11 | bit12 | bit13.
Reviewed-on: http://vgitil04.il.marvell.com:8080/43288
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Hua Jing <jinghua@marvell.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
For armada_37xx_update_reg(), the parameter offset should be pointer so
that it can be updated, otherwise offset will keep old value, and then
when offset is larger than or equal to 32 the mask calculated by
"BIT(offset)" will be 0 in gpio chip hook functions, it's an error,
this patch set offset parameter of armada_37xx_update_reg() as pointer.
Reviewed-on: http://vgitil04.il.marvell.com:8080/43287
Reviewed-by: Hua Jing <jinghua@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Pin 23 on South bridge does not belong to the rgmii group. It belongs to
a separate group which can have 3 functions.
Due to this the fix also have to update the way the functions are
managed. Until now each groups used NB_FUNCS(which was 2) functions. For
the mpp23, 3 functions are available but it is the only group which needs
it, so on the loop involving NB_FUNCS an extra test was added to handle
only the functions added.
The bug was visible when the gpio regulator used the gpio 23, the whole
rgmii group was setup to gpio which broke the Ethernet support on the
Armada 3720 DB board. Thanks to this patch, the UHS SD cards (which need
the vqmmc) _and_ the Ethernet work again.
Reviewed-on: http://vgitil04.il.marvell.com:8080/43284
Reviewed-by: Hua Jing <jinghua@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
On the south bridge we have pin from 0 to 29, so it gives 30 pins (and
not 29).
Reviewed-on: http://vgitil04.il.marvell.com:8080/43285
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Hua Jing <jinghua@marvell.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Clean the iomux definitions at grf_rk3188.h, and move them into
pinctrl-driver for resolving the compiling error of redefinition.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Clean the iomux definitions at grf_rk3036.h, and move them into
pinctrl-driver for resolving the compiling error of redefinition.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
This adds support for the (to date unsupported) I2C controllers 1~4
and 6~7 (i.e. now all controllers except I2C5, which is not accessible
on the RK3399-Q7, are supported by pinctrl).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
- add the 2 new compatible used by STM32MP157
"st,stm32mp157-pinctrl"
"st,stm32mp157-z-pinctrl"
- update the mask for the port
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
|
|
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.
This commit moves the header code:
include/libfdt.h -> include/linux/libfdt.h
include/libfdt_env.h -> include/linux/libfdt_env.h
and replaces include directives:
#include <libfdt.h> -> #include <linux/libfdt.h>
#include <libfdt_env.h> -> #include <linux/libfdt_env.h>
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Signed-off-by: Marek Behun <marek.behun@nic.cz>
|
|
Add entries for the R8A77965 M3N SoC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
|
|
The serial drivers now depend on the pinctrl driver to determine whether
they are enabled. That means if a serial device wants to be used pre-reloc,
we also need the pinctrl device pre-reloc.
Adapt the pinctrl driver as well as dts overlay accordingly.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
