uboot-2021-rebase.git - uboot 2021 rebase, to fix booting on modern SD cards, from https://github.com/fifteenhex/u-boot/tree/am335x_som

Age	Commit message (Collapse)	Author
2008-03-07	net: uec_phy: actually increment the timeout counter	Kim Phillips
	allow u-boot to recover (and, e.g., switch to another interface) in the case where a PHY does not report autonegotiation is complete within its two second timeout value. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-03-02	net: uec_phy: handle 88e1111 rev.B2 erratum 5.6	Kim Phillips
	erratum 5.6 states the autoneg completion bit is functional only if the autoneg bit is asserted. This fixes any secondarily-issued networking commands on non-gigabit links on the mpc8360 mds board. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-01-16	Remove annoying debug printout for PHY less boards.	Joakim Tjernlund
	PHY less board prints out lots of "read wrong ...": read wrong value : mii_id 3,mii_reg 2, base e0102320 read wrong value : mii_id 3,mii_reg 3, base e0102320 UEC: PHY is Generic MII (ffffffff) read wrong value : mii_id 3,mii_reg 4, base e0102320 read wrong value : mii_id 3,mii_reg 0, base e0102320 read wrong value : mii_id 3,mii_reg 1, base e0102320 read wrong value : mii_id 3,mii_reg 1, base e0102320 read wrong value : mii_id 3,mii_reg 5, base e0102320 read wrong value : mii_id 3,mii_reg 1, base e0102320 read wrong value : mii_id 3,mii_reg 1, base e0102320 read wrong value : mii_id 3,mii_reg 5, base e0102320 FSL UEC0: Full Duplex FSL UEC0: Speed 100BT FSL UEC0: Link is up Using FSL UEC0 device Make this printout depend on UEC_VERBOSE_DEBUG and remove its definition in uec_phy.c Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-01-16	net: reduce boot latency on QE UEC based boards	Kim Phillips
	actually polling for PHY autonegotiation to finish enables us to remove the 5 second boot prompt latency present on QE based boards. call to qe_set_mii_clk_src in init_phy, and mv call to init_phy from uec_initialize to uec_init by Joakim Tjernlund; autonegotiation wait code shamelessly stolen from tsec driver. also rm unused CONFIG_RMII_MODE code. Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2007-08-14	Add support for UEC to 8568	Andy Fleming
	Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2006-11-30	Code cleanup.	Wolfgang Denk

2006-11-03	mpc83xx: add QE ethernet support	Dave Liu
	this patch adds support for the QUICC Engine based UCC gigabit ethernet device.