| Age | Commit message (Collapse) | Author |
|---|
|
Add support for multiple DRAM configuration subnodes, while retaining
the support for a single flat DRAM configuration node. This is useful
on systems which can be manufactured in multiple configurations and
where the DRAM configuration can be determined at runtime.
The code is augmented by a function which can be overridden on board
level, allowing a match on the configuration node name, very much like
the fitImage configuration node name matching works. The default match
is on the single top-level DRAM configuration, if matching on subnodes
is required, then this board_stm32mp1_ddr_config_name_match() must be
overridden.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
|
|
Activate ARCH_SUPPORT_TFABOOT and replace the arch stm32mp
specific config CONFIG_STM32MP1_TRUSTED by the generic CONFIG_TFABOOT
introduced by the commit 535d76a12150 ("armv8: layerscape: Add TFABOOT
support").
This config CONFIG_TFABOOT is activated for the trusted boot chain,
when U-Boot is loaded by TF-A.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
|
|
This parameter "st,phy-cal" becomes optional and when it is
absent the built-in PHY calibration is done.
It is the case in the helper dtsi file "stm32mp15-ddr.dtsi"
except if DDR_PHY_CAL_SKIP is defined.
This patch also impact the ddr interactive mode
- the registers of the param 'phy.cal' are initialized to 0 when
"st,phy-cal" is not present in device tree (default behavior when
DDR_PHY_CAL_SKIP is not activated)
- the info 'cal' field can be use to change the calibration behavior
- cal=1 => use param phy.cal to initialize the PHY, built-in training
is skipped
- cal=0 => param phy.cal is absent, built-in training is used (default)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
|
|
These functions relate to memory init so move them into the init
header.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This patch solves the following warnings:
drivers/ram/stm32mp1/stm32mp1_ram.c: In function 'stm32mp1_ddr_clk_enable':
warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
for (idx = 0; idx < ARRAY_SIZE(clkname); idx++) {
^
drivers/ram/stm32mp1/stm32mp1_ram.c: In function 'stm32mp1_ddr_setup':
warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
for (idx = 0; idx < ARRAY_SIZE(param); idx++) {
^
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Force alignment of the size of parameters array with
the expected value in the binding, that allows compilation
error when the array size change.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Allow fractional support in DDR tools.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Add support of trusted boot, using TF-A as first stage bootloader,
The boot sequence is
BootRom >=> TF-A.stm32 (clock & DDR) >=> U-Boot.stm32
The TF-A monitor provides secure monitor with support of SMC
- proprietary to manage secure devices (BSEC for example)
- PSCI for power
The same device tree is used for STMicroelectronics boards with
basic boot and with trusted boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Currently, regmap_init_mem() takes a udevice. This requires the node
has already been associated with a device. It prevents syscon/regmap
from behaving like those in Linux.
Change the first argumenet to take a device node.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have multiple licenses (in
these cases, dual license) declared in the SPDX-License-Identifier tag.
In this case we change from listing "LICENSE-A LICENSE-B" or "LICENSE-A
or LICENSE-B" or "(LICENSE-A OR LICENSE-B)" to "LICENSE-A OR LICENSE-B"
as per the Linux Kernel style document. Note that parenthesis are
allowed so when they were used before we continue to use them.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Add driver and binding for stm32mp1 ddr controller and phy
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
