| Age | Commit message (Collapse) | Author |
|---|
|
Xilinx ZynqMP also contains dual Cortex R5 which can run U-Boot.
This patch is adding minimal support to get U-Boot boot.
U-Boot on R5 runs out of DDR with default configuration that's why
DDR needs to be partitioned if there is something else running on arm64.
Console is done via Cadence uart driver and the first Cadence Triple
Timer Counter is used for time.
This configuration with uart1 was tested on zcu100-revC.
U-Boot 2018.05-rc2-00021-gd058a08d907d (Apr 18 2018 - 14:11:27 +0200)
Model: Xilinx ZynqMP R5
DRAM: 512 MiB
WARNING: Caches not enabled
MMC:
In: serial@ff010000
Out: serial@ff010000
Err: serial@ff010000
Net: Net Initialization Skipped
No ethernet found.
ZynqMP r5>
There are two ways how to run this on ZynqMP.
1. Run from ZynqMP arm64
tftpb 20000000 u-boot-r5.elf
setenv autostart no && bootelf -p 20000000
cpu 4 disable && cpu 4 release 10000000 lockstep
or
cpu 4 disable && cpu 4 release 10000000 split
2. Load via jtag when directly to R5
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
There is no need to have arm hardware header in this driver.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Currently CPU_V7 kconfig symbol supports only ARMv7A architectures under
armv7 folder. This led to a misconception of creating separate folders
for armv7m and armv7r. There is no reason to create separate folder for
other armv7 based architectures when it can co-exist with few Kconfig
symbols.
As a first step towards a common folder, rename CPU_V7 as CPUV7A. Later
separate Kconfig symbols can be added for CPU_V7R and CPU_V7M and
can co exist in the same folder.
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Suggested-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Uart status register is named USART_ISR on STM32F7, STM32H7
and STM32MP1 SoCs family, but USART_SR only on STM32F4 SoCs.
Use USART_ISR_ prefix instead of USART_SR_ .
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Enable uart overrun feature which allows to benefits of uart
FIFO usage.
Previously overrun management was disabled, this has to effect
to bypassed the uart FIFO usage even if FIFO was enabled.
In particular configuration, for example when video console is
enabled, copy/pasting a long command line in console results in
corruption. This is due to the fact that a lot of time is consumed
in flushing the cache during frame buffer update, so uart chars are
not read fast enough.
By using uart FIFO and managing overrun, long command line can by
copy/paste in console without being corrupted.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
|
|
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
The line "-obj-$(CONFIG_STM32_SERIAL) += serial_stm32.o"
is found twice in Makefile.
Fixes: ae74de0dfd45 ("serial: stm32: Rename serial_stm32x7.c to serial_stm32.c"
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add the SCIFA0 address entry so it can be used in TPL if needed
due to size restrictions.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
This patch fixes a situation where CONFIG_DM_SERIAL is enabled for
regular U-Boot and SPL, but not for TPL. In that case, the build
will try to include serial-uclass into the TPL nonetheless, because
CONFIG_DM_SERIAL is set.
The solution is to check if the build is for SPL or TPL and in that
case, check if CONFIG_$(SPL_TPL_)DM_SERIAL is also set. Only in that
case, include serial-uclass.c . If the build is for regular U-Boot,
CONFIG_BUILD is not set, so only check if CONFIG_DM_SERIAL is set
and if so, include serial-uclass.c
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
|
|
The Amlogic Meson SoCs serial bindings were not written when serial
support was pushed into Linux and U-Boot.
A clean bindings document has been merged into Linux tree to correctly
handle the multiple clocks feeding the serial peripheral.
This update the U-Boot serial_meson driver with the new compatible
string for Amlogic Meson GX Socs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This patch removes call of serial initialisation functions that
are not implemented anymore.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
|
|
include/commproc.h is dedicated to the 8xx, rename it cpm_8xx.h and
move it into arch/powerpc/include/asm
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
|
|
CONFIG_8xx doesn't mean much outside of arch/powerpc/
This patch renames it CONFIG_MPC8xx just like CONFIG_MPC85xx etc ...
It also renames 8xx_immap.h to immap_8xx.h to be consistent with
other file names.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
|
|
- add new arch stm32mp for STM32 MPU/Soc based on Cortex A
- support for stm32mp157 SOC
- SPL is used as first boot stage loader
- using driver model for all the drivers, even in SPL
- all security feature are deactivated (ETZC and TZC)
- reused STM32 MCU drivers when it is possible
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
This converts the following to Kconfig:
CONFIG_CONS_INDEX
We have existing entries for this option in a number of places, with
different guards on them. They're also sometimes used for things not
directly inside of the serial driver. First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it. Next, consolidate all of these into the single entry in
drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
After the UART was initialized, we may still have bogus data in the
RX queue if it was enabled with incorrect pin muxing before.
So let's flush the RX queue whenever we initialize baud rates.
This fixes a regression with the dynamic pinmuxing code when enable_uart=1
is not set in config.txt on Raspberry Pis that use pl011 for serial.
Fixes: caf2233b28 ("bcm283x: Add pinctrl driver")
Reported-by: Göran Lundberg <goran@lundberg.email>
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Tuomas Tynkkynen <tuomas@tuxera.com>
|
|
After the UART was initialized, we may still have bogus data in the
RX queue if it was enabled with incorrect pin muxing before.
So let's flush the RX queue whenever we initialize baud rates.
This fixes a regression with the dynamic pinmuxing code when enable_uart=1
is not set in config.txt.
Fixes: caf2233b28 ("bcm283x: Add pinctrl driver")
Reported-by: Göran Lundberg <goran@lundberg.email>
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Tuomas Tynkkynen <tuomas@tuxera.com>
|
|
Do a explicit check for CONFIG_SYS_BIG_ENDIAN and
CONFIG_SYS_LITTLE_ENDIAN to avoid errors on platforms where both
are undefined (x86).
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
|
|
Cosmetic change, replace CONFIG_* with CONFIG_IS_ENABLED(*) .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Commit 608b0c4ad4e5ec0c ("serial: Use next serial device if probing fails")
added code to search for more serial devices if the default one was not
probed correctly.
Unfortunately, that breaks omap3_evm. So while investigating why that is
the case, let's disable the full search for everyone but bcm283x where it
is needed.
Fixes: 608b0c4ad4e5ec0c ("serial: Use next serial device if probing fails")
Reported-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
On bcm2835 we need to ensure we only access serial devices that are
muxed to the serial output pins of the pin header. To achieve this
for the pl011 device, add a bcm2835 specific pl011 wrapper device
that does this check but otherwise behaves like a pl011 device.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Setting config options using headers is deprecated. This patch converts
the BCM2835 Mini-UART to Kconfig.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
We want to use Kconfig logic to depend on whether pl01x devices
are built in, so let's convert their inclusion selection to Kconfig.
This round goes to pl01x.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
We want to use Kconfig logic to depend on whether pl01x devices
are built in, so let's convert their inclusion selection to Kconfig.
This round goes to pl011.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
We want to use Kconfig logic to depend on whether pl01x devices
are built in, so let's convert their inclusion selection to Kconfig.
This round goes to pl010.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
The fdtdec API is deprecated, convert the pl010 and pl011 devices to
use the dev_read API instead.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
The bcm283x mini-uart is only really usable as U-Boot serial output
when it is muxed to the UART pins of the RPi pin header.
So fail probing in case it is not muxed correctly, as in that case
firmware did not initialize it properly either.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
The serial initialization doesn't always quite work for me, so let's
always skip it for now. We know that firmware on the RPi initializes
us properly already.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
The fdtdec API got deprecated in favor of dev_read calls.
Use those instead.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
We are switching to a model where a serial device doesn't even get probed when
it's not muxed properly, so we don't need device specific disabling
functionality anymore.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Currently our serial device search chokes on the fact that the serial
probe function could fail. If it does, instead of searching for the next
usable serial device, it just quits.
This patch changes the fallback logic so that even when a serial device
was not probed correctly, we just try the next ones until we find one that
works.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Clarify the computation precedence in two ternary operator
constructions.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
|
|
|
|
Add support for RZ/A1 series SoCs.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
|
|
Use the common RCAR_GEN2 config option instead of enumerating
each SoC and having a lengthy ifdef clause. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Replace fdtdec_get_addr() with devfdt_get_addr() as the later one is
the current recommended practice.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
wait_for_bit callers use the 32 bit LE version
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
Now this driver is used across stm32f4, stm32f7 and stm32h7
SoCs family, give it a generic name.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
|
|
Identify and distinguish between platform device type of MX7ULP
and LS1021A.
This is a fix to commit 7edf5c45("serial: lpuart: add i.MX7ULP
support").
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Remove serial_stm32.c driver and uart init from board file,
use available DM serial_stm32x7.c driver compatible for
STM32F4/F7 and H7 SoCs.
The serial_stm32x7.c driver will be renamed later with a more
generic name as it's shared with all STM32 Socs.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Unify the CONFIG_R8A7795 and CONFIG_R8A7796 as CONFIG_RCAR_GEN3
so that every time we add a new SoC, we won't have to add more
stuff to this list.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Move cadence/zynq serial driver via Kconfig
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
In U-boot, serial_tstc was use to determine is there have a character in
serial console that pending for read. If there is no "pending" function
implemented in serial driver, the serial-uclass will return "true(1)"
to indicate there have a character pending to read.
Thus, read a character from nulldev serial will result in continuous
getting -EAGAIN return which might lead system to hang.
This commit is to fix a bug in nulldev serial which implement "pending"
function in nulldev serial to always indicate there is no character in
console that pending for read.
Signed-off-by: Wilson Lee <wilson.lee@ni.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Keng Soon Cheah <keng.soon.cheah@ni.com>
Cc: Chen Yee Chew <chen.yee.chew@ni.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
|
|
Uniformize STMicroelectronics copyrights headers for STM32
related code.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Uniformize all STMicroelectronics copyrights headers for STi
related code.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Fix typos in USB tty driver.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
|
