| Age | Commit message (Collapse) | Author |
|---|
|
Add a timer driver for the MPC83xx architecture.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
|
|
Add timer driver for the Designware APB Timer IP. This is present
for example on the Altera SoCFPGA chips.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
|
|
This driver was tested on Xilinx ZynqMP SoC.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This timer driver is using GPT Timer (General Purpose Timer)
available on all STM32 SOCs family.
This driver can be used on STM32F4/F7 and H7 SoCs family
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
ATCPIT100 is often used in AE3XX platform which is
based on NDS32 architecture recently. But in the future
Andestech will have AE250 platform which is embeded
ATCPIT100 timer based on RISCV architecture.
Signed-off-by: Rick Chen <rick@andestech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
ATCPIT100 is Andestech timer IP which is embeded
in AE3XX and AE250 boards. So rename AE3XX to
ATCPIT100 will be more make sence.
Signed-off-by: rick <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add the new Atmel PIT timer driver, which supports the driver model
and device tree.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
|
|
This adds a device-model driver for the timer block in the RK3368 (and
similar devices that share the same timer block, such as the RK3288) for
the down-counting (i.e. non-secure) timers.
This allows us to configure U-Boot for the RK3368 in such a way that
we can run with the secure timer inaccessible or uninitialised (note
that the ARMv8 generic timer does not count, if the secure timer is
not enabled).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
To fully support DM timer in SPL and TPL, we need a few things cleaned
up and normalised:
- inclusion of the uclass and drivers should be an all-or-nothing
decision for each stage and under control of $(SPL_TPL_)TIMER
instead of having the two-level configuration with TIMER and
$(SPL_TPL_)TIMER_SUPPORT
- when $(SPL_TPL_)TIMER is enabled, the ARMv8 generic timer code can
not be compiled in
This normalises configuration to $(SPL_TPL_)TIMER and moves the config
options to drivers/timer/Kconfig (and cleans up the collateral damage
to some defconfigs that had SPL_TIMER_SUPPORT enabled).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Without a timer, U-Boot just doesn't boot. This is not something
we can turn off.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Support Andestech AE3xx platform: serial, timer device tree flow.
Signed-off-by: rick <rick@andestech.com>
|
|
Support AG101P timer device tree flow.
Signed-off-by: rick <rick@andestech.com>
|
|
This commit introduces timer driver for ARC.
ARC timers are configured via ARC AUX registers so we use special
functions to access timer control registers.
This driver allows utilization of either timer0 or timer1
depending on which one is available in real hardware. Essentially
only existing timers should be mentioned in board's Device Tree
description.
Signed-off-by: Vlad Zakharov <vzakhar@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add ARM global timer based timer
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add support for Watchdog Timer, which is compatible with AST2400 and
AST2500 watchdogs. There is no uclass for Watchdog yet, so the driver
does not follow the driver model. It also uses fixed clock, so no clock
driver is needed.
Add support for timer for Aspeed ast2400/ast2500 devices.
The driver actually controls several devices, but because all devices
share the same Control Register, it is somewhat difficult to completely
decouple them. Since only one timer is needed at the moment, this should
be OK. The timer uses fixed clock, so does not rely on a clock driver.
Add sysreset driver, which uses watchdog timer to do resets and particular
watchdog device to use is hardcoded (0)
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
In some cases the timer must be accessible before driver model is active.
Examples include when using CONFIG_TRACE to trace U-Boot's execution before
driver model is set up. Enable this option to use an early timer. These
functions must be supported by your timer driver: timer_early_get_count()
and timer_early_get_rate().
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Adding a timer driver for omap devices based on driver model
and device tree.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
|
|
To group all dm timer drivers together, move tsc timer to
drivers/timer directory.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
This changes 'Timer' to 'timer' at several places.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add a sandbox timer which get time from host os and a basic
test.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Convert altera timer to driver model.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Chin Liang See <clsee@altera.com>
|
|
Implement a Timer uclass to work with lib/time.c.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Simon Glass <sjg@chromium.org>
|
