summaryrefslogtreecommitdiff
path: root/drivers/tsec.c
AgeCommit message (Collapse)Author
2007-07-04drivers/: Augment CONFIG_COMMANDS tests with defined(CONFIG_CMD_*).Jon Loeliger
This is a compatibility step that allows both the older form and the new form to co-exist for a while until the older can be removed entirely. All transformations are of the form: Before: #if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT) After: #if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT) || defined(CONFIG_CMD_AUTOSCRIPT) Signed-off-by: Jon Loeliger <jdl@freescale.com>
2007-05-17Reduce CONFIG_MPC8YXX_TSECx to CONFIG_TSECxKim Phillips
For all practical u-boot purposes, TSECs don't differ throughout the mpc8[356]xx families; reduce CONFIG_MPC8YXX_TSECx to CONFIG_TSECx. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2007-05-15Add support for BCM5464 Quad PhyJoe Hamman
Added support for Broadcom's BCM5464 Quad Phy Signed-off-by: Joe Hamman <joe.hamman@embeddedspecialties.com>
2007-05-05Coding stylke cleanup; update CHANGELOG.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2007-05-02Add support for treating unknown PHYs as generic PHYs.David Updegraff
When bringing up u-boot on new boards, PHY support sometimes gets neglected. Most PHYs don't really need any special support, though. By adding a generic entry that always matches if nothing else does, we can provide support for "unsupported" PHYs for the tsec. The generic PHY driver supports most PHYs, including gigabit. Signed-off-by: David Updegraff <dave@cray.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2007-04-23Enable 8544 supportAndy Fleming
* Add support to the Makefile * Add 8544 configuration support to the tsec driver * Add 8544 SVR numbers to processor.h Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: Jon Loeliger <jdl@freescale.com>
2007-03-02mpc83xx: U-Boot support for Wind River SBC8349Paul Gortmaker
I've redone the SBC8349 support to match git-current, which incorporates all the MPC834x updates from Freescale since the 1.1.6 release, including the DDR changes. I've kept all the SBC8349 files as parallel as possible to the MPC8349EMDS ones for ease of maintenance and to allow for easy inspection of what was changed to support this board. Hence the SBC8349 U-Boot has FDT support and everything else that the MPC8349EMDS has. Fortunately the Freescale updates added support for boards using CS0, but I had to change spd_sdram.c to allow for board specific settings for the sdram_clk_cntl (it is/was hard coded to zero, and that remains the default if the board doesn't specify a value.) Hopefully this should be mergeable as-is and require no whitespace cleanups or similar, but if something doesn't measure up then let me know and I'll fix it. Thanks, Paul.
2006-11-03mpc83xx: Add support for the MPC8349E-mITXTimur Tabi
PREREQUISITE PATCHES: * This patch can only be applied after the following patches have been applied: 1) DNX#2006090742000024 "Add support for multiple I2C buses" 2) DNX#2006090742000033 "Multi-bus I2C implementation of MPC834x" 3) DNX#2006091242000041 "Additional MPC8349 support for multibus i2c" 4) DNX#2006091242000078 "Add support for variable flash memory sizes on 83xx systems" 5) DNX#2006091242000069 "Add support for Errata DDR6 on MPC 834x systems" CHANGELOG: * Add support for the Freescale MPC8349E-mITX reference design platform. The second TSEC (Vitesse 7385 switch) is not supported at this time. Signed-off-by: Timur Tabi <timur@freescale.com>
2006-11-03Added RGMII support to the TSECs and Marvell 881111 PhyNick Spence
Added a phy initialization to adjust the RGMII RX and TX timing Always set the R100 bit in 100 BaseT mode regardless of the TSEC mode Signed-off-by: Nick Spence <nick.spence@freescale.com>
2006-10-26Fix TSEC driver (now for real): avoid crashes if PHY is not attachedBen Warren
to a TSEC (e.g. a switch is connected via RMII) or if the PHY is defective/incorrectly configured. Signed-off-by: Ben Warren <bwarren@qstreams.com>
2006-10-12Remove unneeded include files and local variable.Jon Loeliger
Signed-off-by: Jon Loeliger <jdl@freescale.com>
2006-10-10Ran lindent and cleaned up whitespace issues.Jon Loeliger
Format for 80-columns too.
2006-09-19Merge branch 'mpc85xx'Jon Loeliger
Conflicts: drivers/tsec.c
2006-09-19Add support for eTSEC 3 & 4 on 8548 CDSAndy Fleming
* Added support for using eTSEC 3 and eTSEC 4 on the 8548 CDS. This will only work on rev 1.3 boards (but doesn't break older boards) * Cleaned up some comments to reflect the expanded role of tsec in other systems
2006-06-27Fix Tsec bug when no linkJin Zhengxiong-R64188
When tftp a non-exist file from the tftp server, u-boot will check the link of all eth port. The original file will return wrong link state on the no link ports. signed-off-by: Jason Jin <Jason.Jin@freescale.com>
2006-04-26Initial support for MPC8641 HPCN board.Jon Loeliger
2006-03-31GCC-4.x fixes: clean up global data pointer initialization for all boards.Wolfgang Denk
2006-03-12Add Nat Semi DP83865 PHY support to MPC85xx TSEC driverWolfgang Denk
Patch by Murray Jensen, 08 Jul 2005
2005-10-28Add support for multiple PHYs.Marian Balakowicz
2005-10-13Cleanup for GCC-4.xWolfgang Denk
2005-09-21Fix autonegotiation in tsec ethernet driverStefan Roese
Patch by Stefan Roese, 21 Sep 2005
2005-08-01Fix style issues primarily in 85xx and 83xx boards.Jon Loeliger
- C++ comments - Trailing white space - Indentation not by TAB - Excessive amount of empty lines - Trailing empty lines
2005-07-28* Patch by Eran LibertyEran Liberty
Add support for the Freescale MPC8349ADS board.
2005-07-25* Patch by Jon Loeliger, 2005-07-25Jon Loeliger
Move the TSEC driver out of cpu/mpc85xx as it will be shared by the upcoming mpc83xx family as well.
generated by cgit (git 2.34.1) at 2024-12-29 05:26:38 +0000