| Age | Commit message (Collapse) | Author |
|---|
|
Adds support for Amlogic G12A USB Control Glue HW.
The Amlogic G12A SoC Family embeds 2 USB Controllers :
- a DWC3 IP configured as Host for USB2 and USB3
- a DWC2 IP configured as Peripheral USB2 Only
A glue connects these both controllers to 2 USB2 PHYs, and optionnally
to an USB3+PCIE Combo PHY shared with the PCIE controller.
The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including
routing of the OTG PHY between the DWC3 and DWC2 controllers, and
setups the on-chip OTG mode selection for this PHY.
This driver sets the OTG capable port as Host mode by default,
the switch to Device mode is to be done in a separate patch.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
This make the driver more generic. At this point this driver can replace
the dwc3-of-simple implementation.
Make the description in the Kconfig more generic too.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
By enabling BLK by default this is the next driver which needs to get
support for DM_USB. Adding generic DWC3 glue logic which only
parse nodes and read device mode. Based on it probe proper
host/peripheral DWC3 drivers for it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Add UniPhier platform specific glue layer to support USB3 Host mode
on Synopsys DWC3 IP.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
We see the choice of USB_DWC3_HOST / _GADGET in drivers/usb/dwc3/Kconfig,
but we can not choose USB_DWC3_HOST unless USB_GADGET is defined.
This is strange.
Loosen the "depends on" and also move "select USB_GADGET_DUALSPEED" to
the correct place.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
|
|
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
|
|
Description was borrowed from kernel dwc3 Kconfig.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
|
|
Move CONFIG_USB_GADGET_DUALSPEED option to Kconfig and
make all UDC controllers select USB_GADGET_DUALSPEED:
- add next options to Kconfig selecting USB_GADGET_DUALSPEED:
- USB_GADGET_ATMEL_USBA
- USB_GADGET_DWC2_OTG
- USB_DWC3
- CI_UDC
- make USB_MUSB_GADGET select USB_GADGET_DUALSPEED
While at it, make some related fixes:
- remove DUALSPEED from configs that don't enable gadget support:
- kwb.h
- tseries.h
- add missing USB_GADGET option to next configs:
- novena_defconfig
- pcm051_rev*_defconfig
- xfi3_defconfig
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
|
|
removed un-used/un-supported files from dwc3. These files can be added
later as and when the support is added.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
Added dwc3 folder from linux kernel 3.19-rc1 (97bf6af1f9)
to u-boot. This will be adapted to work with u-boot in the
following patches.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
|
