| Age | Commit message (Collapse) | Author |
|---|
|
dwc3-generic has been broken since MISC uclass has been modified to scan DT
sub-nodes after bind.
Fixing it by a using the no-op uclass.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
There is simply no reason to do that here.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
Adds support for Amlogic G12A USB Control Glue HW.
The Amlogic G12A SoC Family embeds 2 USB Controllers :
- a DWC3 IP configured as Host for USB2 and USB3
- a DWC2 IP configured as Peripheral USB2 Only
A glue connects these both controllers to 2 USB2 PHYs, and optionnally
to an USB3+PCIE Combo PHY shared with the PCIE controller.
The Glue configures the UTMI 8bit interfaces for the USB2 PHYs, including
routing of the OTG PHY between the DWC3 and DWC2 controllers, and
setups the on-chip OTG mode selection for this PHY.
This driver sets the OTG capable port as Host mode by default,
the switch to Device mode is to be done in a separate patch.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
The BITMAP related operations can now be moved to ./include/linux/bitmap.h
file to mimic the Linux kernel directory tree.
This change also allows to remove the lin_gadget_compat.h header file
(which is a legacy code only for composite U-boot layer).
It was also possible to remove #includes from several USB gadget drivers.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
|
|
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
The error is:
In file included from include/part.h:10:0,
from include/usb.h:18,
from include/linux/usb/gadget.h:22,
from drivers/usb/dwc3/ep0.c:20:
include/ide.h:62:14: error: unknown type name ‘uchar’
void ide_led(uchar led, uchar status);
Fixing it by including common.h that defines the uchar type.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
The select_dr_mode operation is executed when the glue driver is probed.
The role of this optional function is to configure the operating mode
of the controller at the glue level.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
This make the driver more generic. At this point this driver can replace
the dwc3-of-simple implementation.
Make the description in the Kconfig more generic too.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
UCLASS_USB_DEV_GENERIC was meant for USB devices connected to host
controllers, not gadget devices.
Adding a new UCLASS for gadget devices alone.
Also move the generic DM code for USB gadgets in a separate file for
clarity.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
Those operations can be used for peripheral operation as well as host
operation.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
# Conflicts:
# drivers/usb/dwc3/core.c
# drivers/usb/host/xhci-dwc3.c
|
|
The driver will be probed when usb_gadget_initialize() is called.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
|
|
usb_gadget_initialize()/_release()/_handle_interrupt()
When DM_USB_GADGET the platform code for the USB device must be replaced by
calls to a USB device driver.
usb_gadget_initialize() probes the USB device driver.
usb_gadget_release() removes the USB device driver.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
|
|
Using CONFIG_DM_USB for this purpose prevents using DM_USB for host and not
for device.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
|
|
This allows to disable the USB driver model in SPL because it checks
the CONFIG_SPL_DM_USB variable for SPL builds. Nothing changes for
regular non-SPL builds.
Signed-off-by: Sven Schwermer <sven@svenschwermer.de>
|
|
Complete in the drivers directory the work started with
commit 83d290c56fab ("SPDX: Convert all of our single
license tags to Linux Kernel style").
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Add WARN_ONCE definition to allow single time notification
of warnings to the user.
Taken from Linux kernel (4.17) with slight changes
(Removed __section(.data.once))
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
[trini: Drop the musb and dwc3 compat versions]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
devm_zalloc() is already defined in dm/device.h header, so
devm_zalloc can be removed from linux_compact.h beader file.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
By enabling BLK by default this is the next driver which needs to get
support for DM_USB. Adding generic DWC3 glue logic which only
parse nodes and read device mode. Based on it probe proper
host/peripheral DWC3 drivers for it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
The patch is preparing dwc3 core for enabling DM_USB with peripheral
driver with using driver model support.
The driver will be bound by the DWC3 wrapper driver based on the
dr_mode device tree entry.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
(Remove dwc3-omap changes)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Including <common.h> pulls in a lot of bloat. What this driver needs
is BIT(), so replace it with <linux/bitops.h>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Marek Vasut <marex@denx.de>
|
|
Collect runtime BUG/WARN into a self-contained header <linux/bug.h>
to make these macros easier to use.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
When we import code from Linux, with regular re-sync planned, we want
to use printk() and pr_*(). U-Boot does not support them in a clean
way. So, people end up with local macros, or compat headers here and
there, then we occasionally see build errors of definition conflicts.
We have include/linux/compat.h, but putting all sorts of unrelated
things into a single header is just a temporal workaround. Hence this
patch, to find the best home for all printk variants. If you want to
use printk() and friends, please include <linux/printk.h>. This header
is self-contained, and pulls in only a few headers.
When I was testing this clean-up, I noticed the image size exceeded
its platform limit on some boards. This is because all pr_*() that
were previously defined as no-op in include/linux/mtd/mtd.h (unless
CONFIG_MTD_DEBUG is set), are now enabled.
To make such boards happy, this commit also implements CONFIG_LOGLEVEL.
The concept is similar to the kernel parameter "loglevel". (Actually,
the Kconfig help message was taken from kernel-paremeter.txt of Linux)
Messages with a loglevel smaller than console loglevel will be printed.
The difference is the loglevel is build-time determined. To save the
image size, lower priority pr_*() are compiled out. I set the default
of CONFIG_LOGLEVEL to 6, i.e. pr_notice and higher priority messages
are compiled in.
I adjusted CONFIG_LOGLEVEL to avoid build error for some boards.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Add in SPL_LOGLEVEL that is the same as LOGLEVEL]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Add UniPhier platform specific glue layer to support USB3 Host mode
on Synopsys DWC3 IP.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
We see the choice of USB_DWC3_HOST / _GADGET in drivers/usb/dwc3/Kconfig,
but we can not choose USB_DWC3_HOST unless USB_GADGET is defined.
This is strange.
Loosen the "depends on" and also move "select USB_GADGET_DUALSPEED" to
the correct place.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Merely using dma_alloc_coherent does not ensure that there is no stale
data left in the caches for the allocated DMA buffer (i.e. that the
affected cacheline may still be dirty).
The original code was doing the following (on AArch64, which
translates a 'flush' into a 'clean + invalidate'):
# during initialisation:
1. allocate buffers via memalign
=> buffers may still be modified (cached, dirty)
# during interrupt processing
2. clean + invalidate buffers
=> may commit stale data from a modified cacheline
3. read from buffers
This could lead to garbage info being written to buffers before
reading them during even-processing.
To make the event processing more robust, we use the following sequence
for the cache-maintenance:
# during initialisation:
1. allocate buffers via memalign
2. clean + invalidate buffers
(we only need the 'invalidate' part, but dwc3_flush_cache()
always performs a 'clean + invalidate')
# during interrupt processing
3. read the buffers
(we know these lines are not cached, due to the previous
invalidation and no other code touching them in-between)
4. clean + invalidate buffers
=> writes back any modification we may have made during event
processing and ensures that the lines are not in the cache
the next time we enter interrupt processing
Note that with the original sequence, we observe reproducible
(depending on the cache state: i.e. running dhcp/usb start before will
upset caches to get us around this) issues in the event processing (a
fatal synchronous abort in dwc3_gadget_uboot_handle_interrupt on the
first time interrupt handling is invoked) when running USB mass
storage emulation on our RK3399-Q7 with data-caches on.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
The dwc3_flush_cache() call was declared and used inconsistently:
* The declaration assumed 'int' for addresses (a potential issue
when running in a LP64 memory model).
* The invocation cast the address to 'long'.
This change ensures that both the declaration and usage of this
function consistently uses 'uintptr_t' for correct behaviour even
when the allocated buffers (to be flushed) reside outside of the
lower 32bits of memory.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Remove sys_proto.h inclusion which is not used by the driver.
Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
CONFIG_AM57XX is just an unnecessary macro that is redundant given So,
remove the same instead of spreading through out the u-boot source
code and getting in the way to maintain common code for DRA7x family.
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
It is pointless to build gadget driver if USB_GADGET is disabled.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
|
|
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
|
|
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
|
|
Description was borrowed from kernel dwc3 Kconfig.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
|
|
Move CONFIG_USB_GADGET_DUALSPEED option to Kconfig and
make all UDC controllers select USB_GADGET_DUALSPEED:
- add next options to Kconfig selecting USB_GADGET_DUALSPEED:
- USB_GADGET_ATMEL_USBA
- USB_GADGET_DWC2_OTG
- USB_DWC3
- CI_UDC
- make USB_MUSB_GADGET select USB_GADGET_DUALSPEED
While at it, make some related fixes:
- remove DUALSPEED from configs that don't enable gadget support:
- kwb.h
- tseries.h
- add missing USB_GADGET option to next configs:
- novena_defconfig
- pcm051_rev*_defconfig
- xfi3_defconfig
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
|
|
BUILD_BUG_* macros have been defined in several headers. It would
be nice to collect them in include/linux/bug.h like Linux.
This commit is cherry-picking useful macros from include/linux/bug.h
of Linux 4.4.
I did not import BUILD_BUG_ON_MSG() because it would not work if it
is used with include/common.h in U-Boot. I'd like to postpone it
until the root cause (the "error()" macro in include/common.h causes
the name conflict with "__attribute__((error()))") is fixed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
fix the following build warnings:
drivers/usb/dwc3/core.c: In function ‘dwc3_uboot_init’:
drivers/usb/dwc3/core.c:625:6: warning: ‘dev’ is used uninitialized in this function [-Wuninitialized]
mem = devm_kzalloc(dev, sizeof(*dwc) + DWC3_ALIGN_MASK, GFP_KERNEL);
^
drivers/usb/dwc3/dwc3-omap.c: In function ‘dwc3_omap_uboot_init’:
drivers/usb/dwc3/dwc3-omap.c:380:7: warning: ‘dev’ is used uninitialized in this function [-Wuninitialized]
omap = devm_kzalloc(dev, sizeof(*omap), GFP_KERNEL);
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
After consulting with some of the SPDX team, the conclusion is that
Makefiles are worth adding SPDX-License-Identifier tags too, and most of
ours have one. This adds tags to ones that lack them and converts a few
that had full (or in one case, very partial) license blobs into the
equivalent tag.
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Change aritmentics to use 64bit types to be compatible with 64bit
builds.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
add missing definitions for the ubi/ubifs sync
with linux 4.2, also change "#define kfree ..."
into a static inline, so prevent ubi compile error:
CC drivers/mtd/ubi/fastmap.o
drivers/mtd/ubi/fastmap.c: In function 'scan_pool':
drivers/mtd/ubi/fastmap.c:475:3: error: called object 'free' is not a function
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
Added support to power on/power off the second USB PHY present in
DRA7xx and AM57xx.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Writing "0x00" to the USBOTGSS_IRQENABLE_SET_MISC and
USBOTGSS_IRQENABLE_SET_0 doesn't disable the interrupts. Used
USBOTGSS_IRQENABLE_CLR_MISC and USBOTGSS_IRQENABLE_CLR_0 instead.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
New files, namely samsung_usb_phy.c and samsung-usb-phy-uboot.h have
been added to u-boot to provide proper PHY handling at Exynos5 SoCs.
This code is used thereafter in the board_usb_init() call.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Marek Vasut <marex@denx.de>
|
|
For u-boot dwc3 driver the scatter gather list support has been removed
from original linux code. It is correct, since we try to send one request
at a time.
However, the cleanup left spurious break, which caused early exit from
loop at dwc3_cleanup_done_reqs() function. As a result the dwc3_gadget_giveback()
wasn't called and caused USB Mass Storage to hang.
This commit removes this problem and refactor the code to remove superfluous
do { } while(1) loop.
Test HW: Odroid XU3 (with ./test/ums/ums_gadget_test.sh)
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
Commit "drivers/dwc3: add a workaround for too small OUT requests"
sets max packet for OUT requests when transfer is smaller.
Until this change the default maxpacket for non EP0 EPs was 1024. This is
too much, since UMS LBA size is 512B
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
be LST
It turned out that current dwc3 gadget code is preparing multiple TRBs
for a transfer. Unfortunately, when multiple requests are in the same
queue, only for the last one the LST (last) ctrl bit is set.
Due to that dwc3 HW executes all TRBs up till the one marked as last.
Unfortunately, UMS requires call of ->complete callback after any send TRB.
This is the reason for "hangs" in executing UMS.
This code simplifies this situation and set each TRB's ctrl field bit to be
last (LST bit).
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
There is no point in calling dwc3_thread_interrupt() if no event is
pending. There is also no point in flushing event cache in EVERY loop
iteration.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
DWC3 hangs on OUT requests smaller than maxpacket size,
so HACK the request length to be at least equal to maxpacket size.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
This commit makes the dwc3_set_mode() as static, to prevent collisions.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
|
