| Age | Commit message (Collapse) | Author |
|---|
|
These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing functions to avoid confusion.
In the end we will have:
1. dev_read_addr...() - works on devices, supports flat/live tree
2. devfdt_get_addr...() - current functions, flat tree only
3. of_get_address() etc. - new functions, live tree only
All drivers will be written to use 1. That function will in turn call
either 2 or 3 depending on whether the flat or live tree is in use.
Note this involves changing some dead code - the imx_lpi2c.c file.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
LS2081ARDB board is similar to LS2080ARDB board with few differences
It hosts LS2081A SoC
Default boot source is QSPI-boot
It does not have IFC interface
RTC and QSPI flash device are different
It provides QIXIS access via I2C
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
|
|
Currently the controller by default enables the Receive Detect feature in P3
mode in USB 3.0 PHY. However, USB 3.0 PHY does not reliably support receive
detection in P3 mode.
Enabling the USB3 controller to configure USB in P2 mode whenever the Receive
Detect feature is required.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
|
|
transfers requests
This is required for better performance, and performs below tuning:
1. Enable burst length set, and define it as 4/8/16.
2. Set burst request limit to 16 requests.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
|
|
Now, include/linux/errno.h is a wrapper of <asm-generic/errno.h>.
Replace all include directives for <asm-generic/errno.h> with
<linux/errno.h>.
<asm-generic/...> is supposed to be included from <asm/...> when
arch-headers fall back into generic implementation. Generally, they
should not be directly included from .c files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Add drivers/usb/host/xhci-rockchip.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This makes functions much simpler.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Adds code to use driver model for USB XHCI FSL driver
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
|
|
This patch is doing the following:
1. Implementing the errata for LS2080.
2. Adding fixup for fdt for LS2080.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
|
|
This patch removes unsued function usb_phy_reset, rather common function
dwc3_phy_reset is used.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@freescale.com>
|
|
Remove LS102XA immap header inclusion from xhci fsl driver.
It removes redefinition warnings when built for platforms
other than LS102XA
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
|
|
This adjusts (micro)frame length to appropriate value thus
avoiding USB devices to time out over a longer run
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
|
|
Replace uint32_t with uintptr_t to remove compilation
warnings for 64-bit architectures.
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
|
|
Add xhci driver support for all FSL socs
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
|
