| Age | Commit message (Collapse) | Author |
|---|
|
|
|
wait_for_bit callers use the 32 bit LE version
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
flags member of struct timing was not initialized,
this took to unpredictable behaviour of display flags,
such DISPLAY_FLAGS_HSYNC_HIGH instead of _LOW etc.
Init timing->flags = 0
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
The LCDC IP-core an be feed from several clock sources, one of those is
a dedicated DPLL for generating a dividable base-clock for this IP-core.
The TRM specifies the maximum input frequency for the LCCD with 200 MHz,
so we must not exceed this value with the PLL frequency (which can lock
much higher).
This patch tries every combination of multipliers and divisors of the
PLL and the IP-core itself for getting as near as possible the the
requested panel->pxl_clk.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
|
|
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
|
|
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
|
|
The calculation of left space for version string is not correct, should
use VIDEO_COLS not VIDEO_LINE_LEN / 2, otherwise we will get larger space
than actual have and cause string to overlay logo picture.
Also current version string display only supports two lines words at max.
This also causes overlay when the LCD pixel column size is not enough.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Anatolij Gustschin <agust@denx.de>
|
|
The clk_set_rate function dereferences the clk pointer without
checking whether it is NULL. This may cause problem when clk is NULL.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
|
These are actually different bits, and since some monitors (Benq BL2420PT)
have modes with different HSYNC and VSYNC polarity, we should set them
independently
Tested on Pine64-LTS with Benq BL2420PT monitor.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
Add support for setting up SimpleFB for LCD display output in DE2
SimpleFB setup code.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
When HDMI is not initialized (e.g. no monitor is plugged), the current
SimpleFB code will still create a broken SimpleFB node.
Detect whether HDMI is initialized when creating SimpleFB node.
Fixes: be5b96f0e411 ("sunxi: setup simplefb for Allwinner DE2")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
CC: Simon Glass <sjg@chromium.org>
CC: Minkyu Kang <mk7.kang@samsung.com>
|
|
Resort to malloc_cache_aligned() rather than malloc() which also removes
'CACHE: Misaligned operation at range' warnings.
Signed-off-by: Niko Mauno <niko.mauno@vaisala.com>
|
|
Extend DE2 driver with LCD support. Tested on Pinebook which is based
on A64 and has ANX6345 eDP bridge with eDP panel connected to it.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
[agust: rebased v5 on u-boot-video/master]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
|
It will be reused in new DM LCD driver.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
|
|
This is a eDP bridge similar to ANX9804, it allows to connect eDP panels
to the chips that can output only parallel signal
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
[agust: fixed most checkpatch errors/warnings]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
|
This header will be used in anx6345 driver
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
[agust: moved header to drivers/video]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
|
Add an operation to read EDID, since bridge may have ability to read
EDID from the panel that is connected to it, for example LCD<->eDP bridge.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
|
|
As the support of EFI boot on Allwinner H3 is broken, we still need to
use simplefb to pass the framebuffer to Linux.
Add code to setup simplefb for Allwinner DE2 driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Add an option to indicate that the video driver should setup a SimpleFB
node that passes the video framebuffer initialized by U-Boot to the
operating system kernel.
Currently only the Allwinner DE driver uses this option, and the
definition of this option in the sunxi-common.h config header is
converted to an imply of this option from CONFIG_VIDEO_SUNXI.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
As the DE2 simplefb setup code can also benefit from the simplefb match
code, extract it to a new source file.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
|
|
U-Boot widely uses error() as a bit noisier variant of printf().
This macro causes name conflict with the following line in
include/linux/compiler-gcc.h:
# define __compiletime_error(message) __attribute__((error(message)))
This prevents us from using __compiletime_error(), and makes it
difficult to fully sync BUILD_BUG macros with Linux. (Notice
Linux's BUILD_BUG_ON_MSG is implemented by using compiletime_assert().)
Let's convert error() into now treewide-available pr_err().
Done with the help of Coccinelle, excluing tools/ directory.
The semantic patch I used is as follows:
// <smpl>
@@@@
-error
+pr_err
(...)
// </smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Re-run Coccinelle]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Note that this doesn't differentiate (due to lack of information in
video_priv) between different possible component orders for 32bpp.
But the main user at this point is efi_loader, and GOP expects xBGR
so any video drivers that this is incorrect for already have problems.
(Also, conveniently, this matches what simple-framebuffer bindings
expect for kernels that use the simple-framebuffer DT binding to
take over the bootloader display.)
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Really just the subset that is needed by efi_console. Perhaps more will
be added later, for example color support would be useful to implement
efi_cout_set_attribute().
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Content can come to screen via putc() and we cannot always rely on
updates ending with a puts(). This is the case with efi_console output
to vidconsole. Fixes corruption with Shell.efi.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
|
|
The use-case is that the thing that loaded u-boot already put a splash
image on screen. And we want to preserve that until grub boot menu
takes over.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
Not really qcom specific, but for now qcom/lk is the one firmware that
is (afaiu) setting up the appropriate dt node for pre-configured
display. Uses the generic simple-framebuffer DT bindings so this should
be useful on other platforms.
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
|
The STM32 LTDC display controller provides a parallel digital RGB and
signals for horizontal, vertical synchronization, Pixel Clock and Data
Enable as output to interface directly to a variety of LCD and TFT panels.
The LTDC main features are:
- 24-bit RGB Parallel Pixel Output, Programmable timings & polarity for
HSync, VSync and Data Enable.
- 2 layers with Blending, Color Keying, Window position & size,
Dithering, Background color, Color Look-Up Table (CLUT).
- Supported layer color formats: ARGB8888, RGB888, RGB565, ARGB1555,
ARGB4444, L8 CLUT, AL44 & AL88
This LTDC driver:
- supports: RGB parallel output with timings & polarity, 1 layer
in RGB565.
- supports but with hard-coded configurations: blending, window
position & size (crop), background color.
- does not support yet: rgb888, argb8888, 8-bit clut, dithering.
This LTDC driver is compatible with all stm32 platforms with the
LTDC IP and has been tested on stm32 f746-disco board.
Signed-off-by: Philippe CORNU <philippe.cornu@st.com>
|
|
Add a driver for GPIO backlights.
It understands the standard device tree binding.
It can be used with simple-panel when PWM is not necessary.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Add a config to select individually the driver for PWM backlights.
Manage "depends on" to be backyard compatible.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
MX6Q/QP IPU operates at 264MHz and MX6DL IPU at 198MHz.
When running a SPL target, which supports multiple MX6 variants we cannot
properly setup the IPU clock frequency via CONFIG_IPUV3_CLK option as
such decision is done in build-time currently.
Remove the CONFIG_IPUV3_CLK option and let the IPU clock frequency be
configured in run-time on mx6.
Reported-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
[agust: fixed #endif in cgtqmx6eval.h]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
|
Boards can skip display interface init using board_video_skip().
If display interface was not initialized (e.g. no ipuv3 framebuffer
registered or IPU clock disabled), booting Linux stops due to the
crash in IPU shutdown function, when accessing IPU registers.
Check IPU clock and skip shutdown if clock is not enabled.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
|
This reverts commit 1d20170467b079642be96996dcd71db64c3c365c, reversing
changes made to 6aee2ab68c362ace5a59f89a63abed82e0bf19e5.
The mxc_ipuv3_fb.c changes introduce build failures on some targets.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Boards can skip display interface init using board_video_skip().
If display interface was not initialized (e.g. no ipuv3 framebuffer
registered or IPU clock disabled), booting Linux stops due to the
crash in IPU shutdown function, when accessing IPU registers.
Check IPU clock and skip shutdown if clock is not enabled.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
|
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.
Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Add rk3288 soc specific driver for mipi dsi.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
Add Makefile item for soc specific driver for rk3399 mipi dsi.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
To compatible with different rockchip soc, we split the mipi dirver into
common and soc specific parts, and all the soc share the common
functions from common driver part.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[agust: fix build breakage and warnings]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
|
|
This is not used in U-Boot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This is not used in U-Boot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This is not used in U-Boot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This is not used in U-Boot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Update these drives to support a live device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
Tested-by: Stephen Warren <swarren@nvidia.com>
|
|
Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/<SOC>.
This change is also coherent with the structure in kernel.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Akshay Bhat <akshaybhat@timesys.com>
CC: Ken Lin <Ken.Lin@advantech.com.tw>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Heiko Schocher <hs@denx.de>
CC: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
CC: Christian Gmeiner <christian.gmeiner@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Patrick Bruenn <p.bruenn@beckhoff.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Nikita Kiryanov <nikita@compulab.co.il>
CC: Otavio Salvador <otavio@ossystems.com.br>
CC: "Eric Bénard" <eric@eukrea.com>
CC: Jagan Teki <jagan@amarulasolutions.com>
CC: Ye Li <ye.li@nxp.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Adrian Alonso <adrian.alonso@nxp.com>
CC: Alison Wang <b18965@freescale.com>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Martin Donnelly <martin.donnelly@ge.com>
CC: Marcin Niestroj <m.niestroj@grinn-global.com>
CC: Lukasz Majewski <lukma@denx.de>
CC: Adam Ford <aford173@gmail.com>
CC: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr>
CC: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Soeren Moch <smoch@web.de>
CC: Richard Hu <richard.hu@technexion.com>
CC: Wig Cheng <wig.cheng@technexion.com>
CC: Vanessa Maegima <vanessa.maegima@nxp.com>
CC: Max Krummenacher <max.krummenacher@toradex.com>
CC: Stefan Agner <stefan.agner@toradex.com>
CC: Markus Niebel <Markus.Niebel@tq-group.com>
CC: Breno Lima <breno.lima@nxp.com>
CC: Francesco Montefoschi <francesco.montefoschi@udoo.org>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Scott Wood <oss@buserror.net>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Anatolij Gustschin <agust@denx.de>
CC: Simon Glass <sjg@chromium.org>
CC: "Andrew F. Davis" <afd@ti.com>
CC: "Łukasz Majewski" <l.majewski@samsung.com>
CC: Patrice Chotard <patrice.chotard@st.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Stephen Warren <swarren@nvidia.com>
CC: Andre Przywara <andre.przywara@arm.com>
CC: "Álvaro Fernández Rojas" <noltari@gmail.com>
CC: York Sun <york.sun@nxp.com>
CC: Xiaoliang Yang <xiaoliang.yang@nxp.com>
CC: Chen-Yu Tsai <wens@csie.org>
CC: George McCollister <george.mccollister@gmail.com>
CC: Sven Ebenfeld <sven.ebenfeld@gmail.com>
CC: Filip Brozovic <fbrozovic@gmail.com>
CC: Petr Kulhavy <brain@jikos.cz>
CC: Eric Nelson <eric@nelint.com>
CC: Bai Ping <ping.bai@nxp.com>
CC: Anson Huang <Anson.Huang@nxp.com>
CC: Sanchayan Maity <maitysanchayan@gmail.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Patrick Delaunay <patrick.delaunay@st.com>
CC: Gary Bisson <gary.bisson@boundarydevices.com>
CC: Alexander Graf <agraf@suse.de>
CC: u-boot@lists.denx.de
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
|
|
|
|
Add some debugging to show when the backlight is enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
|
|
Update this driver to support a live device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
|
