| Age | Commit message (Collapse) | Author |
|---|
|
The existing imx_watchdog driver is compatible with mx25 chipsets.
Add a WDOG1_BASE_ADDR define for the base address and enable the driver
in watchdog's Makefile.
To use the driver, a board must define CONFIG_IMX_WATCHDOG and
CONFIG_HW_WATCHDOG.
This fixes an issue when booting an mx25 chip via usb/serial. In this
case, the boot rom will always enable the watchdog. If u-boot is running
in interactive mode and the watchdog is not serviced, the system is
rebooted when the watchdog expires.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
|
|
This adds support for the CPU watchdog found on Marvell Armada 37xx
SoCs.
There are 4 counters which can be set as CPU watchdog counters.
This driver uses the second counter (ID 1, counting from 0)
(Marvell's Linux also uses second counter by default).
In the future it could be adapted to use other counters, with
definition in the device tree.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
In preparation of DM watchdog, move basic actions into drivers/watchdog
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
|
|
This IP can be found on Zynq and ZynqMP devices.
The driver was tested with reset-on-timeout; feature.
Also adding WATCHDOG symbol to Kconfig because it is required.
Signed-off-by: Shreenidhi Shedi <imshedi@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Add watchdog driver for Intel Tangier based platforms.
Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
The Orion watchdog can be found on some Marvell Armada chips.
This driver is based on the code by Tomas Hlavacek in the CZ.NIC
turris-omnia-uboot repository, which can be found at
https://gitlab.labs.nic.cz/turris/turris-omnia-uboot, and that
one is based on code by Sylver Bruneau. His code is already in
mainline Linux kernel.
The code uses the new driver model API.
Signed-off-by: Tomas Hlavacek <tomas.hlavacek@nic.cz>
Signed-off-by: Marek Behun <marek.behun@nic.cz>
create mode 100644 drivers/watchdog/orion_wdt.c
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This driver is a simplified version of linux/drivers/watchdog/bcm63xx_wdt.c
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Paolo Pisati <p.pisati@gmail.com>
|
|
This driver supports ast2500 and ast2400 SoCs.
Only ast2500 supports reset_mask and thus the option of resettting
individual peripherals using WDT.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This is a simple uclass for Watchdog Timers. It has four operations:
start, restart, reset, stop. Drivers must implement start, restart and
stop operations, while implementing reset is optional: It's default
implementation expires watchdog timer in one clock tick.
Signed-off-by: Maxim Sloyko <maxims@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
These drivers have no user since commit ea3310e8aafa ("Blackfin:
Remove").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
This driver implements the HW WATCHDOG functions. Which needs
to set CONFIG_HW_WATCHDOG to use them. This is disabled by default for
mx7ulp.
Use watchdog for reset cpu. Implement this in the driver.
Need to define CONFIG_ULP_WATCHDOG to build it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Since commit 623d96e89aca6("imx: wdog: correct wcr register settings")
issuing a 'reset' command causes the system to hang.
Unlike i.MX and Vybrid, the watchdog controller on LS102x is big-endian.
This means that the watchdog on LS1021 has been working by accident as
it does not use the big-endian accessors in drivers/watchdog/imx_watchdog.c.
Commit 623d96e89aca6("imx: wdog: correct wcr register settings") only
revelead the endianness problem on LS102x.
In order to fix the reset hang, introduce a reset_cpu() implementation that
is specific for ls102x, which accesses the watchdog WCR register in big-endian
format. All that is required to reset LS102x is to clear the SRS bit.
This approach is a temporary workaround to avoid a regression for LS102x
in the 2015.10 release. The proper fix is to make the watchdog driver
endian-aware, so that it can work for i.MX, Vybrid and LS102x.
Reported-by: Sinan Akman <sinan@writeme.com>
Tested-by: Sinan Akman <sinan@writeme.com>
Reviewed-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Add imx-common cpu support for imx7d SoC
- Update reset_cause for imx7d
- Enable watchdog driver built for imx7d
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
|
|
This is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Chan-Taek Park <c-park@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
|
|
The QorIQ LS1 family is built on Layerscape architecture,
the industry's first software-aware, core-agnostic networking
architecture to offer unprecedented efficiency and scale.
Freescale LS102xA is a set of SoCs combines two ARM
Cortex-A7 cores that have been optimized for high
reliability and pack the highest level of integration
available for sub-3 W embedded communications processors
with Layerscape architecture and with a comprehensive
enablement model focused on ease of programmability.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
|
|
To add the DesignWare watchdog driver support. It required
information such as register base address and clock info from
configuration header file within include/configs folder.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
|
|
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
|
|
Add TI OMAP 16xx & 24xx/34xx 32KHz (non-secure) watchdog support.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
|
|
Conflicts:
drivers/serial/Makefile
|
|
This patch adds watchdog support for Vybrid VF610 platform.
Signed-off-by: Alison Wang <b18965@freescale.com>
|
|
- Enable hw_watchdog_init() in watchdog.h if CONFIG_HW_WATCHDOG is defined.
- Move blackfin hw watchdog driver to the generic driver folder.
- Call hw_watchdog_init() from blackfin board init code.
- Reuse macro CONFIG_WATCHDOG_TIMEOUT_MSECS
- Update README.watchdog accordingly
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
|
|
Watchdog can be used on Microblaze, PPC and Zynq hw designs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
|
|
Use a common watchdog driver for all these cpus.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David Müller <d.mueller@elsoft.ch>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: U-Boot DM <u-boot-dm@lists.denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Oliver Brown <obrown@adventnetworks.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: U-Boot DM <u-boot-dm@lists.denx.de>
|
|
Faraday ftwdt010 watchdog is an architecture independant
watchdog. It is usually used in SoC chip design.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils. As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".
This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.
The name of each former library archive is preserved except for
extensions which change from ".a" to ".o". This commit updates
references accordingly where needed, in particular in some linker
scripts.
This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols. Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.
Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
|
|
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
