| Age | Commit message (Collapse) | Author |
|---|
|
The TWSI_FREQUENCY macro was wrong in 2 ways:
1) It was casting the result of the calculations to an u8, while i2c clk
rates are often >= 100Khz which won't fit in a u8, drop the cast.
2) It had an extra factor of 2 in the divider which neither the datasheet nor
the Linux driver have.
The comment for the default value was wrongly saying that m lives in
bits 4-7, while in reality it is in bits 3-6, as can be seen from the correct
shift by 3 used in i2c_init().
While at it remove the unused twsi_actual_speed variable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Added USB host driver for zynq.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
We need to flip only one bit not assign.
Signed-off-by: Marek Belisko <marek.belisko@gmail.com>
Acked-by: Pekon Gupta <pekon@ti.com>
|
|
|
|
The HW-defined procedure for booting Tegra requires that some pins be
set up as GPIOs immediately at boot in order to avoid glitches on those
pins, when the pinmux is programmed. Add a feature to the GPIO driver
which executes a GPIO configuration table. Board files will use this to
implement the correct HW initialization procedure.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
If CONFIG_API is ever to be enabled on Tegra, this define must be set,
since api/api_storage.c uses it.
A couple of annoyting things about CONFIG_SYS_MMC_MAX_DEVICE
1) It isn't documented in README. The same is true for a lot of similar
defines used by api_storage.c.
2) It doesn't represent MAX_DEVICE but rather NUM_DEVICES, since the
valid values are 0..n-1 not 0..n.
However, I this patch does not address those shortcomings.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
when qe-ucode fails to be uploaded, "deep sleep" will hang.
if there is no qe-ucode, disable qe module for platforms
which support "deep sleep"
Signed-off-by: Zhao Qiang <B45475@freescale.com>
|
|
The T4080 SoC is a low-power version of the T4160.
T4080 combines 4 dual-threaded Power Architecture e6500
cores with single cluster and two memory complexes.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
|
|
Current driver uses a Maximum value for MDIO_HOLD when doing 10G MDIO
access, this is due to an errata A-006260 on T4 rev1.0 which is fixed
on rev2.0, so remove the maximum value to use the default value for rev2.0.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
|
|
T4240RDB board Specification
----------------------------
Memory subsystem:
6GB DDR3
128MB NOR flash
2GB NAND flash
Ethernet:
Eight 1G SGMII ports
Four 10Gbps SFP+ ports
PCIe:
Two PCIe slots
USB:
Two USB2.0 Type A ports
SDHC:
One SD-card port
SATA:
One SATA port
UART:
Dual RJ45 ports
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
[York Sun: fix CONFIG_SYS_QE_FMAN_FW_ADDR in T4240RDB.h]
|
|
|
|
|
|
Use helper function zynq_validate_bitstream so that the
code can be reused easily for different cases of dma transfer.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Use zynq_dma_xfer_init, zynq_align_dma_buffer,
zynq_dma_transfer helper function performing dma
transfers so that the code can be reused easily for
different cases of dma transfer.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Warnings:
drivers/fpga/zynqpl.c:150:32: warning: Using plain integer as NULL pointer
drivers/fpga/zynqpl.c:152:16: warning: Using plain integer as NULL pointer
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Connect FPGA version with appropriate operations
to remove huge switch-cases for every FPGA family.
Tested on Zynq. Spartan2/Spartan3/Virtex2 just compile test.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
No functional changes.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
No functional changes.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
No functional changes.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
No functional changes.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This patch includes following changes :
* Adds gpio pin numbering support for EXYNOS SOCs.
To have consistent 0..n-1 GPIO numbering the banks are divided
into different parts where ever they have holes in them.
* Rename GPIO definitions from GPIO_... to S5P_GPIO_...
These changes were done to enable cmd_gpio for EXYNOS and
cmd_gpio has GPIO_INPUT same as s5p_gpio driver and hence
getting a error during compilation.
* Adds support for name to gpio conversion in s5p_gpio to enable
gpio command EXYNOS SoCs. Function has been added to asm/gpio.h
to decode the input gpio name to gpio number.
Example: SMDK5420 # gpio set gpa00
Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This sets up the linkage from the phydev back to the ethernet device. This
symptom of not doing this which I noticed was:
<NULL> Waiting for PHY auto negotiation to complete....
rather than:
dwmac.1c50000 Waiting for PHY auto negotiation to complete....
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
|
|
Make funtions static which are locally used in file.
Signed-off-by: Manish Badarkhe <badarkhe.manish@gmail.com>
|
|
Some functions in include/net.h are ported from
include/linux/etherdevice.h of Linux Kernel.
For ex.
is_zero_ether_addr()
is_multicast_ether_addr()
is_broadcast_ether_addr()
is_valid_ether_addr();
So, we should use the same function name as that of Linux Kernel,
eth_rand_addr(), for consistency.
Besides, eth_rand_addr() has been implemented as an inline function.
So it should not be surrounded by #ifdef CONFIG_RANDOM_MACADDR.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
As some PHYs have non-standard PHY ID registers, PHY Id can't
be read correctly by current get_phy_id function, so we enable
get_phy_id redefinable to permit specific PHY driver having own
specific get_phy_id function.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
|
|
Function "genphy_parse_link()" used "if (mii_reg & BMSR_ANEGCAPABLE)" before,
but used "if (phydev->supported & SUPPORTED_Autoneg)" now.
So assign "phydev->supported" to "phydev->drv->features" for ar8035
to enable autonegotiation. Then removed the genphy_config_aneg() function.
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
|
|
keystone serial hw support hw flow control. This patch
enables hw flow control for keystone EVMs as an optional
feature based on CONFIG_SERIAL_HW_FLOW_CONTROL.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
|
|
gd->bd->bi_baudrate is a copy of gd->baudrate.
Since baudrate is a common feature for all architectures,
keep gd->baudrate only.
It is true that bi_baudrate was passed to the kernel in that structure
but it was a long time ago.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Michal Simek <monstr@monstr.eu> (For microblaze)
|
|
|
|
This patch adds support for the imx25 lcd display controller.
Signed-off-by: Thomas Diener <dietho@gmx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
|
|
The LTC3676 PMIC includes four DC/DC converters, and three 300mA
LDO Regulators (two Adjustable). The DC/DC converters are adjustable based
on a resistor devider (board-specific).
This adds support for the LTC3676 by creating a namespace unique init function
that uses the PMIC API to allocate a pmic and defines the registers.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
Avoid uding pmic_init() as this forces the model of only allowing a
single PMIC driver to be built at a time.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
|
|
Conflicts:
drivers/net/Makefile
(trivial merge)
|
|
add a possibility to add a medium specific polltimeout
function. So it is possible to define different
poll timeouts.
Used on nand medium, for setting the DFU_MANIFEST_POLL_TIMEOUT
only on nand ubi partitions, which is currently the only
usecase.
Change-Id: If1db5f49b32d93fefa7481e8dfe5b7ccc0e65af4
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
comment in ep0_txstate() states:
"report completions as soon as the fifo's loaded; there's no win
in waiting till this last packet gets acked".
This is wrong for using dfu. In the dfu usecase we must send
a PollTimeout to the host, so the host can wait until the
U-Boot Code is ready for answering new usb requests. So the
answer which contains the PollTimeout must send *before*
U-Boot calls req->complete.
The req->complete is used in the dfu case for flushing the
medium, when entering DFU_STATE_dfuMANIFEST_SYNC state.
Change-Id: Ib2941119c72761e48e15fedbdad1ecce07ae0b3d
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
|
|
This patch contains an implementation of the fastboot protocol on the
device side and documentation. This is based on USB download gadget
infrastructure. The fastboot function implements the getvar, reboot,
download and reboot commands. What is missing is the flash handling i.e.
writting the image to media.
v3 (Rob Herring):
This is based on http://patchwork.ozlabs.org/patch/126798/ with the
following changes:
- Rebase to current mainline and updates for current gadget API
- Use SPDX identifiers for licenses
- Traced the history and added missing copyright to cmd_fastboot.c
- Use load_addr/load_size for transfer buffer
- Allow vendor strings to be optional
- Set vendor/product ID from config defines
- Allow Ctrl-C to exit fastboot mode
v4:
- Major re-write to use the USB download gadget. Consolidated function
code to a single file.
- Moved globals into single struct.
- Use puts and putc as appropriate.
- Added CONFIG_USB_FASTBOOT_BUF_ADDR and CONFIG_USB_FASTBOOT_BUF_SIZE to
set the fastboot transfer buffer.
v5:
- Add CONFIG option documentation to README
- Rebase using new downloader registration
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Signed-off-by: Jesper B. Christensen <jesper.christensen@cobham.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Now that the ci_udc driver supports allocating multiple requests per
endpoint, we can revert the special-case added by a022c1e13c01 "usb:
ums: use only 1 buffer for CI_UDC".
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Modify ci_ep_alloc_request() to return a dynamically allocated request
object, rather than a singleton that's part of the endpoint. This
requires moving various state from the endpoint structure to the request
structure, since we need one copy per request.
The "fast bounce buffer" b_fast is removed by this change rather than
moved to the request object. Instead, we enhance the bounce buffer logic
in ci_bounce()/ci_debounce() to keep the bounce buffer around between
request submissions. This avoids the need to allocate an arbitrarily-
sized bounce buffer up-front, yet avoids incurring the allocation
overhead each time a request is submitted.
A future enhancement would be to actually submit multiple requests to HW
at once. The Linux driver shows that this is possible. That might improve
throughput (depending on the USB protocol in use), since USB could be
performing a transfer to one HW buffer in parallel with whatever SW
actions U-Boot performs on another buffer. However, I have not made this
change as part of this patch, in order to keep SW changes related to
buffer management separate from any change in the way the HW is
programmed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
|
|
|
|
's/zynq_serial_initalize/zynq_serial_initialize/g'
serial_initialize is used by all serial drivers.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Warnings:
drivers/serial/serial_zynq.c:181:1: warning: symbol 'uart_zynq0_init' was not declared. Should it be static?
drivers/serial/serial_zynq.c:181:1: warning: symbol 'uart_zynq0_setbrg' was not declared. Should it be static?
drivers/serial/serial_zynq.c:181:1: warning: symbol 'uart_zynq0_getc' was not declared. Should it be static?
drivers/serial/serial_zynq.c:181:1: warning: symbol 'uart_zynq0_tstc' was not declared. Should it be static?
drivers/serial/serial_zynq.c:181:1: warning: symbol 'uart_zynq0_putc' was not declared. Should it be static?
drivers/serial/serial_zynq.c:181:1: warning: symbol 'uart_zynq0_puts' was not declared. Should it be static?
drivers/serial/serial_zynq.c:182:22: warning: symbol 'uart_zynq_serial0_device' was not declared. Should it be static?
drivers/serial/serial_zynq.c:184:1: warning: symbol 'uart_zynq1_init' was not declared. Should it be static?
drivers/serial/serial_zynq.c:184:1: warning: symbol 'uart_zynq1_setbrg' was not declared. Should it be static?
drivers/serial/serial_zynq.c:184:1: warning: symbol 'uart_zynq1_getc' was not declared. Should it be static?
drivers/serial/serial_zynq.c:184:1: warning: symbol 'uart_zynq1_tstc' was not declared. Should it be static?
drivers/serial/serial_zynq.c:184:1: warning: symbol 'uart_zynq1_putc' was not declared. Should it be static?
drivers/serial/serial_zynq.c:184:1: warning: symbol 'uart_zynq1_puts' was not declared. Should it be static?
drivers/serial/serial_zynq.c:185:22: warning: symbol 'uart_zynq_serial1_device' was not declared. Should it be static?
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Add missing header.
Warnings:
drivers/net/zynq_gem.c:491:5: warning: symbol 'zynq_gem_initialize' was not declared. Should it be static?
drivers/net/zynq_gem.c:542:5: warning: symbol 'zynq_gem_of_init' was not declared. Should it be static?
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
MII is used by this driver.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
The right correspondance between LCD margins and LCD timings is:
* upper margin -> vertical back porch
* lower margin -> vertical front porch
* left margin -> horizontal back porch
* right margin -> horizontal front porch
Signed-off-by: Josh Wu <josh.wu@atmel.com>
|
|
g_dnl_register() currently first attempts to register a composite
driver by name, and then saves the driver name once it's registered.
Internally to the registration code, g_dnl_do_config() is called and
attempts to compare the composite device's name with the list of known
device names. This fails since the composite device's name has not yet
been stored. This means that the first time "ums 0 0" is run, it fails,
but subsequent attempts succeed.
Re-order the name-saving and registration code to solve this.
Fixes: e5b834e07f51 ("USB: gadget: added a saner gadget downloader registration API")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Preprocessor definitions and hardcoded implementation selection in
g_dnl core were replaced by a linker list made of (usb_function_name,
bind_callback) pairs.
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Marek Vasut <marex@denx.de>
|
|
Previously offsets handled by dfu_fill_entity_mmc(), defined in boards'
CONFIG_DFU_ALT were treated as hexadecimal regardless of their prefix,
which sometimes led to confusion. This patch forces usage of explicit
numerical base prefixes.
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Tom Rini <trini@ti.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
|
|
When user attempted to perform a raw write using DFU (vide
dfu_fill_entity_mmc) with MMC interface not initialized before,
get_mmc_blk_size() reported invalid (zero) block size - it wasn't
possible to write ie. a new u-boot image.
This commit fixes that by initializing MMC device before use in
dfu_fill_entity_mmc().
While fixing initialization sequence, I had to change about half of
dfu_fill_entity_mmc's body, so I refactored it on the way to make it,
IMHO, considerably more comprehensible.
Being left as dead code, get_mmc_blk_size() was removed.
Tested on Samsung Goni.
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Tom Rini <trini@ti.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
|
