| Age | Commit message (Collapse) | Author |
|---|
|
In phy_connect_dev(), if the phy device has an accociated mac device
before, a warning message will be printed. But we should test the
old device against the new one, if they are actually the same one,
don't print the warning message.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
In get_phy_device_by_mask(), when no phy is found, currently we only
print a message to show the first phy address that is not found. But
this is not always the case as multiple phys can be specified by
phy_mask. Change to print all phys that are not found, and to reduce
the console boot log, change to use 'debug' instead of 'printf'.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
In get_phy_device_by_mask(), when no phy is found, we should not
create any phy device.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
NAND-tree is used to check wiring between MAC and PHY using NAND gates
on the PHY side, hence the name.
NAND-tree initial status is latched at reset by probing the IRQ pin.
However some devices are sharing the PHY IRQ pin with other peripherals
such as Atmel SAMA5D[34]x-EK boards when using the optional TM7000
display module, therefore they are switching the PHY in NAND-tree test
mode depending on the current IRQ line status at reset.
This patch ensure PHY is not in NAND-tree test mode only for the Micrel
KSZ8051 PHY used by Atmel. There are other Micrel PHY affected but I
doubt they are used on such weird hardware design.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Casting from dev->priv to pci_dev_t changes the value's size on a 64-bit
system. This causes the compiler to complain about casting a pointer to an
integer of a different (smaller) size. To avoid this, cast to an integer
of matching size first, then perform an int->int cast to perform the size
change. This signals explicitly that we do want to change the size, and
avoids the compiler warning. This is legitimate since we know the pointer
actually stores a small integer, not a pointer value.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
This patch adds support for Micrel KSZ8021RNL & KSZ8031RNL.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Using NAKs on empty RX fifo for bulk in transfers is the right choice
for a interrupt driven model, but U-Boot uses polling and expects an
immediate answer if there is no incoming packet. Using ZLP Bulk In Response
(BIR) mode avoids unexpected timeouts in the host controller driver.
As ZLP mode is reset default, there is no need to set it.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
smsc95xx_recv() does not reassemble bursts spread over multiple URBs.
If there is a lot of broadcast traffic, the fifo will fill up to the
burst cap limit. Lowering the burst cap to the URB size ensures no packet
spans multiple urbs.
Caveat, lower limit for working burst cap is 5/33 HS/FS packets.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
In the "Getting Started with Coccinelle - KVM edition" presentation that
has been held by Julia Lawall at the KVM forum 2015 (see the slides at
http://events.linuxfoundation.org/sites/events/files/slides/tutorial_kvm_0.pdf),
she pointed out some bad return value checks in U-Boot that can be
detected with Coccinelle by using the following config file:
@@
identifier x,y;
identifier f;
statement S;
@@
x = f(...);
(
if (x < 0) S
|
if (
- y
+ x
< 0) S
)
This patch now fixes these issues.
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
|
|
For current U-Boot to initialize status LEDs via status_led_init(), it
is required to have both CONFIG_STATUS_LED and STATUS_LED_BOOT defined.
This may be a particular concern with GPIO LEDs, where __led_init() is
required to correctly set up the GPIO (gpio_request and
gpio_direction_output). Without STATUS_LED_BOOT the initialization isn't
called, which could leave the user with a non-functional "led" command -
due to the fact that the LED routines in gpio_led.c use gpio_set_value()
just fine, but the GPIO never got set up properly in the first place.
I think having CONFIG_STATUS_LED is sufficient to justify a
corresponding call to status_led_init(), even with no STATUS_LED_BOOT
defined. To do so, common/board_r.c needs call that routine, so it now
is exposed via status_led.h.
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
[trini: Add dummy __led_init to pca9551_led.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
For boards that support LEDs driven via GPIO (CONFIG_GPIO_LED),
it may be useful to have some generic stubs (wrapper functions)
for the "colored" LEDs.
This allows defining STATUS_LED_* values directly to GPIO numbers,
e.g.: #define STATUS_LED_GREEN 248 /* = PH24 */
To keep those optional, it's probably best to introduce an additional
configuration setting. I've chosen CONFIG_GPIO_LED_STUBS for that.
Placing the code in drivers/misc/gpio_led.c also ensures that it
automatically depends on CONFIG_GPIO_LED too.
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add driver model support for keystone serial driver.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Convert altera_tse to driver model and phylib.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Convert altera sysid to driver model with misc uclass.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Implement a Miscellaneous uclass with generic read or
write operations. This class is used only for those
do not fit other more general classes.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Both altera_jtag_serial_initialize() and
altera_serial_initialize() are no longer used after
they are converted to driver model.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
|
|
Convert altera timer to driver model.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Chin Liang See <clsee@altera.com>
|
|
Implement a Timer uclass to work with lib/time.c.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Convert altera_pio to driver model.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Convert altera_spi to driver model
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
|
Convert altera_uart to driver model.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
|
|
Convert altera_jtag_uart to driver model.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
With DM_GPIO, gpio parameters like ACTIVE_(LOW/HIGH) are to be
parsed in xlate gpio drivers-ops. Since xlate is not implemented
in omap_gpio driver, the driver considers all gpio to be
ACTIVE_HIGH which is the default case and fails to return actual
gpio status for ACTIVE_LOW gpios. So adding .xlate ops to
omap_gpio.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Adding compatibles for am335x, am437x and dra7 platforms.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
found in dt
In some platforms like am437x, serial node is not populated with
clock-frequency node. So in that case have a default clock-clock
frequency.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
adopt omap_hsmmc driver to device driver model
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
|
|
Add MMC support for k2g
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
|
|
remove unused code as the same is achieved when configuring sgmii
and link status is verifed.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
In K2G, Ethernet doesn't support SGMII instead it support RGMII,
adding support to the driver to connect to RGMII phy.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Fix Linkram size.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Phy mode is a board property and it can be different between
multiple board and ports, so it should not be hardcoded in
driver to one specific mode. So adding a field in eth_priv_t
structure to pass phy mode to driver.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
|
|
Introduce a dummy driver for sandbox that allows us to verify basic
functionality. This is not meant to do anything functional - but is
more or less meant as a framework plumbing debug helper.
The sandbox remoteproc driver maintains absolutey no states and is a
simple driver which just is filled with empty hooks. Idea being to give
an approximate idea to implement own remoteproc driver using this as a
template.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Many System on Chip(SoC) solutions are complex with multiple processors
on the same die dedicated to either general purpose of specialized
functions. Many examples do exist in today's SoCs from various vendors.
Typical examples are micro controllers such as an ARM M3/M0 doing a
offload of specific function such as event integration or power
management or controlling camera etc.
Traditionally, the responsibility of loading up such a processor with a
firmware and communication has been with a High Level Operating
System(HLOS) such as Linux. However, there exists classes of products
where Linux would need to expect services from such a processor or the
delay of Linux and operating system being able to load up such a
firmware is unacceptable.
To address these needs, we need some minimal capability to load such a
system and ensure it is started prior to an Operating System(Linux or
any other) is started up.
NOTE: This is NOT meant to be a solve-all solution, instead, it tries to
address certain class of SoCs and products that need such a solution.
A very simple model is introduced here as part of the initial support
that supports microcontrollers with internal memory (no MMU, no
execution from external memory, or specific image format needs). This
basic framework can then (hopefully) be extensible to other complex SoC
processor support as need be.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
adopt cpsw driver to device driver model
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
prepare driver for device model migration
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
|
|
The current check is incorrect and will fail when any non-zero byte is read.
Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
At present this driver uses bind() to set up the device. The bind() method
should not touch the hardware, so move the init code to probe().
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
Add a comment to make it clear to which block the #endif relates.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
It is useful to see a message from the debug UART early during boot so that
you know things are working. Add an option to enable this. The message will
be displayed as soon as debug_uart_init() is called.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Some boards need to set things up before the debug UART can be used. On
these boards a call to debug_uart_init() is insufficient. When this option
is enabled, the function board_debug_uart_init() will be called when
debug_uart_init() is called. You can put any code here that is needed to
set up the UART ready for use, such as set pin multiplexing or enable
clocks.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
We want to be able to add other common code to this function. So change the
driver's version to have an underscore before it, just like
_debug_uart_putc(). Define debug_uart_init() to call this version.
Update all drivers to this new method.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Add the Wildcat Point ID so Broadwell U based boards can use SPI.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
To support graphics card behind a PCI bridge, the bridge control
register (offset 0x3e) in the configuration space must turn on
VGA address forwarding.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
Currently pci_last_busno() only checks the last bridge device
under the first UCLASS_PCI device. This is not the case when
there are multiple bridge devices.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
When pci_find_class() fails to find a device, it returns -ENODEV.
But now we check the return value against -1. Fix it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
|
|
PCI_COMMAND_IO bit must be set for VGA device as it needs to respond
to legacy VGA IO address.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
The current code returns 0 even if it failed to find or bind a driver. The
caller then has to check the returned device to see if it is NULL. It is
better to return an error code in this case so that it is clear what
happened.
Adjust the code to return -EPERM, indicating that the device was not bound
because it is not needed for pre-relocation use. Add comments so that the
return value is clear.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
One debug() statement is missing a newline. The other has a repeated word.
Fix these.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
When the auto-configuration process fails for a device (generally due to
lack of memory) we should return the error correctly so that we don't
continue to try memory allocations which will fail.
Adjust the code to check for errors and abort if something goes wrong.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
