| Age | Commit message (Collapse) | Author |
|---|
|
If the bootcounter address is in a cached memory,
a flush of dcache must occur after updateing the bootcounter.
Issue found on i.MX6 where bootcounter is put into the internal
(cached) IRAM.
Signed-off-by: Stefano Babic <sbabic@denx.de>
|
|
|
|
rk3066 and rk3188 has two I2C controller implementations.
Current I2C driver wan't work with legacy implementation.
Switching between controllers is performed using a bit inside
GFR_SOC_CON1 register. The bit setting is performed by pinctrl
driver. The patch ask pinctrl to do settings.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[fix warnings by including the rk3228 variant in the compatible-list]:
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
|
|
HSE and LSE bypass shall support both analog and digital signals.
This patch add a way to select digital bypas case in the device tree
and set the associated bit DIGBYP in RCC_BDCR and RCC_OCEN register
during clock tree initialization.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Add ADC clock gating, that may be used by STM32 ADC.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Alignment with kernel clock driver
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
This patch add clk_enable/clk_disable/clk_get_rate support for
- DSI_PX
- LTDC_PX
- DSI_K (only get rate)
These clocks are needed for LTDC and DSI drivers with latest device tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
the function compute the VCO PLL freq, used in
- stm32mp1_read_pll_freq()
- pll_set_rate()
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
# Conflicts:
# drivers/clk/clk_stm32mp1.c
|
|
This patch define RCC_PLLNCFGR2_SHIFT to reuse it in
the pll function for set rate.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
|
|
Following next kernel rcc bindings, we must use a MFD
RCC driver which is able to bind both clock and reset
drivers.
We can reuse and adapt RCC MFD driver already available
for MCU SoCs (F4/F7/H7).
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Use new API syscon_node_to_regmap in sysreset_syscon driver
for compatible "syscon-reboot"; that's avoid the need of explicit
syscon binding for "regmap" handle.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
For qemu-x86 the date command produces wrong days of the week:
Date: 2018-07-06 (Saturday) Time: 18:02:03
Date: 2018-07-07 (unknown day) Time: 21:02:06
According to a comment in the Linux driver the mc146818 only updates the
day of the week if the register value is non-zero.
Sunday is 1, saturday is 7 unlike in U-Boot (see data sheet
https://www.nxp.com/docs/en/data-sheet/MC146818.pdf).
So let's use our library function to determine the day of the week.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
It's good to print a message when doing reset.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This adds a generic reset driver for x86 processor.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Our implementation of rtc_to_tm() cannot handle dates of more than
0x7fffffff seconds after 1970-01-01.
Adopt the Linux kernel implementation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
Add Sandbox driver for SMEM. mostly stub operations.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
The Shared Memory Manager driver implements an interface for allocating
and accessing items in the memory area shared among all of the
processors in a Qualcomm platform.
Adapted from the Linux driver (4.17)
Changes from the original Linux driver:
* Removed HW spinlock mechanism, which is irrelevant
in U-boot particualar use case, which is just reading from the smem.
* Adapted from Linux driver model to U-Boot's.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This is a uclass for Shared memory manager drivers.
A Shared Memory Manager driver implements an interface for allocating
and accessing items in the memory area shared among all of the
processors.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
|
|
QEMU provides an emulated ARM AMBA PrimeCell PL031 RTC.
The patch sets the base address in the board include file according to the
definition in hw/arm/virt.c of the QEMU source. It defines the Kconfig
option for the existing driver, and enables the RTC driver in
qemu_arm64_defconfig and qemu_arm_defconfig as well as the date command.
We need an RTC to provide the GetTime() runtime service in the UEFI
subsystem.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Tested-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
|
|
This patch adds a delay when regulators are disabled.
This delay is set to 5 ms to cover all use cases.
The worst use case actually seen is during a SD card power cycle.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
In case of phy are provided from a PHY provider nodes as following:
usbphyc: usb-phy@5a006000 {
compatible = "st,stm32mp1-usbphyc";
reg = <0x5a006000 0x1000>;
clocks = <&rcc_clk USBPHY_K>;
resets = <&rcc_rst USBPHY_R>;
#address-cells = <1>;
#size-cells = <0>;
usbphyc_port0: usb-phy@0 {
reg = <0>;
phy-supply = <&vdd_usb>;
vdda1v1-supply = <®11>;
vdda1v8-supply = <®18>
#phy-cells = <0>;
};
usbphyc_port1: usb-phy@1 {
reg = <1>;
phy-supply = <&vdd_usb>;
vdda1v1-supply = <®11>;
vdda1v8-supply = <®18>
#phy-cells = <1>;
};
};
and PHY are called as following:
usbh_ehci: usbh-ehci@5800d000 {
compatible = "generic-ehci";
reg = <0x5800d000 0x1000>;
clocks = <&rcc_clk USBH>;
resets = <&rcc_rst USBH_R>;
interrupts = <GIC_SPI 75 IRQ_TYPE_NONE>;
companion = <&usbh_ohci>;
phys = <&usbphyc_port0>;
phy-names = "usb";
status = "okay";
};
generic_phy_get_by_index() must be updated to first look for
PHY phandle as previously and in case of error looks for PHY
provider by finding the parent's current node which is the PHY
provider.
args (ofnode_phandle_args struct) must also be updated by inserting
the phy index into the PHY provider as args[0].
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Correctly manage the SDMMC reset and card cycle power
to fully handle the power cycle added in the MMC uclass
and avoid issue with level-shifter with some uSDCARD.
3 states managed in driver:
1/ reset: SDMMC disable, signal HiZ
2/ power-cycle: SDMMC disable, signals drive to 0
3/ power-on: SDMMC enabled
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
|
|
Disable the use of function zynq_loadfs when compiling
the driver for the SPL, as the following filesystem
functions are not found by the linker:
- fs_set_blk_dev
- fs_read
- fs_set_blk_dev
- fs_read
- fs_read
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Watchdog can be started before probe and u-boot should just take control
over it. That's why do not stop watchdog in probe to cover cases where
watchdog can expire before probe and start.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
IP itself has no reg/no bit which can be used for this functionality.
Add this note to the driver to make sure that none will be asking for
that. Current method is to setup 1s timeout and hang() which is done via
wdt_expire_now().
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Converting GPIO to DM requires to do changes in reset subsystem
that's why support for Microblaze soft reset via sysreset and GPIO
sysreset support was added.
These two patches enables enabling GPIO DM.
Microblaze soft reset is bind at last reset method.
GPIO reset is handled via sysreset with adding this fragment to DT.
gpio-restart {
compatible = "gpio-restart";
gpios = <&reset_gpio 0 0 0>;
/* 3rd cell ACTIVE_HIGH = 0, ACTIVE_LOW = 1 */
};
hard-reset-gpio property is not documented and also handled.
Conversion is required.
Unfortunately do_reset is required for SPL that's why use only soft
microblaze reset for now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Xilinx Axi wdt driver conversion to driver model & Kconfig update
for the same.
Signed-off-by: Shreenidhi Shedi <yesshedi@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
This patch is enabling GPIO_DM support to have an option to use this
driver together with zynq gpio driver.
!DM part is kept there till Microblaze is cleanup which will be done
hopefully soon.
Just a note:
There is no reason to initialize uc-priv->name because it is completely
unused.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Microblaze is storing reset vector at address 0x0.
It means soft reset can be done by just jumping to this address.
This code was in platform code but sysreset interface is providing
enough capabilities to have more options how to reset the system. It can
go from gpio reset through watchdog reset till soft reset.
The driver has not compatible string because this is cpu specific and DM
core is not able to detect compatible string in DT root that's why this
driver will be instantiated from platform code by calling
device_bind_driver(gd->dm_root, "mb_soft_reset", "reset_soft",
NULL);
It should be bind as the last reset method to ensure that hw reset is
called before this.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
The Linux kernel has binding for gpio-restart node.
This patch is adding basic support without supporting any optional
properties.
This driver was tested on Microblaze system where gpio is connected to
SoC reset logic.
Output value is handled via gpios cells values.
In gpio_reboot_request() set_value is writing 1 because
dm_gpio_set_value() is capable to changing it when it is ACTIVE_LOW.
...
if (desc->flags & GPIOD_ACTIVE_LOW)
value = !value;
...
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
There should be proper bank name setup to distinguish between different
gpio drivers. Use dev->name for it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Remove bogus zynq_gpio_getplat_data() and read driver data directly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Relocate gpio ops as was done by:
"dm: Add support for all targets which requires MANUAL_RELOC"
(sha1: 484fdf5ba058b07be5ca82763aa2b72063540ef3)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Relocate sysreset ops as was done by:
"dm: Add support for all targets which requires MANUAL_RELOC"
(sha1: 484fdf5ba058b07be5ca82763aa2b72063540ef3)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Just fix error message.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Relocate watchdog ops as was done by:
"dm: Add support for all targets which requires MANUAL_RELOC"
(sha1: 484fdf5ba058b07be5ca82763aa2b72063540ef3)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
uclass name is used by dev_read_alias_seq which return seq number when
aliases are used.
Code fragment:
168 int dev_read_alias_seq(struct udevice *dev, int *devnump)
169 {
170 ofnode node = dev_ofnode(dev);
171 const char *uc_name = dev->uclass->uc_drv->name;
172 int ret;
173
174 if (ofnode_is_np(node)) {
175 ret = of_alias_get_id(ofnode_to_np(node), uc_name);
Also this patch enables DM_UC_FLAG_SEQ_ALIAS to be in sync with Linux
which is also using watchdog name for watchdog aliases.
drivers/watchdog/watchdog_core.c:215:
ret = of_alias_get_id(wdd->parent->of_node, "watchdog");
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This patch basically adds two new commands for loadig secure
images.
1. zynq rsa adds support to load secure image which can be both
authenticated or encrypted or both authenticated and encrypted
image in xilinx bootimage(BOOT.bin) format.
2. zynq aes command adds support to decrypt and load encrypted
image back to DDR as per destination address. The image has
to be encrypted using xilinx bootgen tool and to get only the
encrypted image from tool use -split option while invoking
bootgen.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Explanation from Simon Glass
"Private data is created when the device is probed and freed when the
device is removed.
Platform data is created when the device is bound, and survives
probe/remove cycles.
Strictly speaking, platform data should be used to hold the decoded
device tree properties. Private data should be used for run-time
things the device needs to keep track of."
Based on description the driver needs to be switch to use platdata
instead of priv.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This patch fixed the same if/else part error by adding the required
source select on the basis of is_pre_src check.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
Use live-tree function.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
|
|
This commit adds paired dev info for winbond w25q16jv
(tested w25q16jvssiq with a i.mx6 board)
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
Add support for the Macronix mx25l1633e nor flash. (Tested on a imx6 board)
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
Add support for the Gigadevice gd25q16c nor flash. (Tested on a imx6 board)
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
This commit adds the following flashes to the id-table
- W25Q16JV
- W25Q32JV
- W25Q64JV
- W25Q128JV
- W25Q256JV
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
This patch adds qspi driver support for ZynqMP SoC. This
driver is responsible for communicating with qspi flash
devices.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
[jagan: removed GQSPI_MIO_NUM_ macros]
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
Update the xilinx spi driver to support a live tree.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
This patch is for the startup block issue in the spi controller.
SPI clock is passing through STARTUP block to FLASH. STARTUP block
don't provide clock as soon as QSPI provides command. So, first
command fails.
This patch added support to read JEDEC id in xilinx_spi_xfer ().
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
