summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2019-07-15mmc: skip select_mode_and_width for MMC SPI hostAnup Patel
The MMC mode and width are fixed for MMC SPI host hence we skip sd_select_mode_and_width() and mmc_select_mode_and_width() for MMC SPI host. Signed-off-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-15mmc: retry a few times if a partition switch failedJean-Jacques Hiblot
This operation may fail. Retry it a few times before giving up and report a failure. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15mmc: do not change mode when accessing a boot partitionJean-Jacques Hiblot
Accessing the boot partition had been error prone with HS200 and HS400 and was disabled. The driver first switched to a lesser mode and then switched the partition access. It was mostly due to a bad handling of the switch and has been fixed, so let's remove this 'feature' Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15mmc: During a switch, poll on dat0 if available and check the final statusJean-Jacques Hiblot
The switch operation can sometimes make the bus unreliable, in that case the send_status parameter should be false to indicate not to poll using CMD13. If polling on dat0 is possible, we should use it to detect the end of the operation. At the end of the operation it is safe to use CMD13 to get the status of the card. It is important to do so because the operation may have failed. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15mmc: When switching partition, use the timeout specified in the ext_csdJean-Jacques Hiblot
The e-MMC spec allows the e-MMC to specify a timeout for the partition switch command. It can take up to 2550 ms. There is no lower limit to this value in the spec, but do as the the linux driver does and force it to be at least 300ms. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15mmc: use the generic timeout for cmd6 (SWITCH) provided in the ext_csdJean-Jacques Hiblot
Starting with rev 4.5, the eMMC can define a generic timeout for the SWITCH command. Following Linux Kernel code, the timeout also changed from 1000 -> 500 Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15mmc: if possible, poll the busy state using DAT0Jean-Jacques Hiblot
Using the DAT0 line as a rdy/busy line is an alternative to reading the status register of the card. It especially useful in situation where the bus is not in a good shape, like when modes are switched. This is also how the linux driver behaves. Note of warning: As per the specification, while polling on DAT0 the CLK must not turned off: "[...] Without a clock edge the Device (unless previously disconnected by a deselect command (CMD7)) will force the DAT0 line down, forever. [...]" Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15mmc: add mmc_poll_for_busy() and change the purpose of mmc_send_status()Jean-Jacques Hiblot
mmc_send_status() is currently used to poll the card until it is ready, not actually returning the status of the card. Make it return the status and add another function to poll the card. Also remove the 'extern' declaration in the mmc-private.h header to comply with the coding standard. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15mmc: omap_hsmmc: provide wait_dat0 even if UHS modes are not supportedJean-Jacques Hiblot
This function can also be used for eMMC devices. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15Revert "mmc: Add a new callback function to perform the 74 clocks cycle ↵Jean-Jacques Hiblot
sequence" This reverts commit 318a7a576bc49aa8b4207e694d3fbd48c663d6ac. The last and only user of this callback had been the omap_hsmmc driver. It is not used anymore. Removing the callback. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15mmc: omap_hsmmc: don't fill the send_init_stream callbackJean-Jacques Hiblot
This is not required. The MMC core sends CMD0 right after the initialization and it serves the same purpose. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15mmc: omap_hsmmc: reset FSM for DAT and CMD lines if needed before a new commandJean-Jacques Hiblot
It sometimes happen that the PSTATE register does not indicate that the bus is ready when it really is. This usually happens after a mode switch. In that case it makes sense to reset the FSM handling the CMD and DATA Also reset the FSMs if the STATE register cannot be cleared. This also sometimes happens after a mode switch. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15mmc: rpmb: fix response type of CMD25Akio Hirayama
The response type of CMD25 is R1 instead of R1b. Signed-off-by: Akio Hirayama <hirayama.akio@socionext.com> [masahiro: add log ] Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2019-07-15mmc: sdhci: Implement SDHCI card detectT Karthik Reddy
Card detect function implemented for SDHCI framework. Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-07-15mmc: sdhci: Read cd-gpio from devicetreeT Karthik Reddy
This patch reads cd-gpio property from devicetree Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-07-15mmc: Read sd card detect properties from DTT Karthik Reddy
This patch reads card detect properties from device tree & added mmc capability macros in mmc.h. Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-07-14Merge tag 'u-boot-stm32-20190712' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-stm - syscon: add support for power off - stm32mp1: add op-tee config - stm32mp1: add specific commands: stboard and stm32key - add stm32 mailbox driver - solve many stm32 warnings when building with W=1 - update stm32 gpio driver
2019-07-13regulator: Allow autosetting fixed regulatorsSven Schwermer
Fixed regulators don't have a set_value method. Therefore, trying to set their value will always return -ENOSYS. Signed-off-by: Sven Schwermer <sven@svenschwermer.de> Cc: Jaehoon Chung <jh80.chung@samsung.com> Cc: Peng Fan <peng.fan@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-07-13gpio: add gpio-hog supportHeiko Schocher
add gpio-hog support. GPIO hogging is a mechanism providing automatic GPIO request and configuration as part of the gpio-controller's driver probe function. for more infos see: doc/device-tree-bindings/gpio/gpio.txt Signed-off-by: Heiko Schocher <hs@denx.de> Tested-by: Michal Simek <michal.simek@xilinx.com> (zcu102) Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-13pinctrl: pinctrl-single: Add 'pinctrl-single, bits' supportAdam Ford
The TI Davinci (da850/l138/am1808) use pinctrl-single,bits for pinmuxing peripherals. This patch allosw the pinctrl-single driver to parse the pinctrl-single,bits options and correctly setup devices. Signed-off-by: Adam Ford <aford173@gmail.com>
2019-07-13power: regulator: Kconfig: Add SPL_DM_REGULATOR configs for ↵Keerthy
palmas/lp873x/lp87565 Add SPL_DM_REGULATOR configs for palmas/lp873x/lp87565. These were missing and the Makefile already assumes them to be defined. Add the corresponding SPL config options. This enables the regulator support in SPL. Signed-off-by: Keerthy <j-keerthy@ti.com>
2019-07-13power: pmic: Kconfig: Add SPL_PMIC configs for palmas/lp873x/lp87565Keerthy
Add SPL_PMIC configs for palmas/lp873x/lp87565. These were missing and the Makefile already assumes them to be defined. Add the corresponding SPL config options. This enables the pmics in SPL. Signed-off-by: Keerthy <j-keerthy@ti.com>
2019-07-13rtc: add Microcrystal RV-8803 driverMichael Walle
Signed-off-by: Michael Walle <michael@walle.cc>
2019-07-13usb: musb-new: omap2430: Fix compilation warning with USB_MUSB_GADGETDerald D. Woods
This commit addresses the following warning, when _NOT_ USB_MUSB_HOST: [...] CC drivers/usb/gadget/f_mass_storage.o CC drivers/usb/musb-new/omap2430.o CC drivers/usb/gadget/f_fastboot.o CC env/common.o CC env/env.o /src/etinker/software/u-boot-master/drivers/usb/musb-new/omap2430.c: In function ‘omap2430_musb_probe’: /src/etinker/software/u-boot-master/drivers/usb/musb-new/omap2430.c:239:6: warning: assignment to ‘int’ from ‘struct musb *’ makes integer from pointer without a cast [-Wint-conversion] ret = musb_register(&platdata->plat, ^ LD drivers/usb/host/built-in.o CC drivers/usb/gadget/f_sdp.o CC fs/ext4/ext4fs.o [...] Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
2019-07-13rtc: ds1307: add support for m41t11Heiko Schocher
add m41t11 support in ds1307 driver. changes: - add compatible string for m41t11 - check if RTC clock is running, if not enable the clock Signed-off-by: Heiko Schocher <hs@denx.de>
2019-07-13mmc: Register only the first MMC device on MMC_TINYEzequiel Garcia
When MMC_TINY is enabled, support for only one MMC device is provided. Boards that register more than one device, will just write over mmc_static keeping only the last one registered. This commit prevents this, keeping only the first MMC device created. A debug warning message is added, if nothing else, as a hint/documentation for developers. Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
2019-07-13spl: Move SPL_MMC_TINY option to appear under SPL menuEzequiel Garcia
The SPL_MMC_TINY implements feature-reduced MMC support on SPL, and as such, it's more consistent and convenient to find it as part of the SPL configuration. Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
2019-07-12drivers: core: use strcmp when find device by namePeng Fan
`if (!strncmp(dev->name, name, strlen(name)))` might find out the wrong device, it might find out `dram_pll_ref_sel`, when name is `dram_pll`. So use strcmp to avoid such issue. Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-12pci: ensure enumeration of all devices in pci_initMarek Behún
Use the uclass_first_device_check and uclass_next_device_check functions instead of uclass_first_device and uclass_next_device in pci_init. This ensures that all PCI devices are tried to be probed. Currently if a device fails to probe, the enumeration stops and the devices which come after the failed device are not probed. Signed-off-by: Marek Behún <marek.behun@nic.cz> Cc: Stefan Roese <sr@denx.de> Cc: Anton Schubert <anton.schubert@gmx.de> Cc: Dirk Eibach <dirk.eibach@gdsys.cc> Cc: Mario Six <mario.six@gdsys.cc> Cc: Chris Packham <chris.packham@alliedtelesis.co.nz> Cc: Phil Sutter <phil@nwl.cc> Cc: VlaoMao <vlaomao@gmail.com> Cc: Tom Rini <trini@konsulko.com> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-12gpio: stm32: Remove .ofmatch callbackPatrice Chotard
As compatible string "st,stm32-gpio" is no more used, .ofmatch callback becomes useless, remove it. Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12pinctrl: stm32: update .bind callbackPatrice Chotard
Update .bind callback in order to bind all pinctrl subnodes with "gpio-controller" property to gpio_stm32 driver. Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12gpio: stm32: Rename stm32f7_gpio to stm32_gpioPatrice Chotard
As this driver is used on stm32f4/f7/h7 and stm32mp1 SoCs, rename it with a more generic name. Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12spi: stm32: Fix warnings when compiling with W=1Patrick Delaunay
This patch solves the following warnings: drivers/spi/stm32_spi.c: In function 'stm32_spi_write_txfifo': drivers/spi/stm32_spi.c:116:20: warning: comparison between signed and unsigned integer expressions [-Wsign-compare] if (priv->tx_len >= sizeof(u32) && ^~ drivers/spi/stm32_spi.c:122:27: warning: comparison between signed and unsigned integer expressions [-Wsign-compare] } else if (priv->tx_len >= sizeof(u16) && ^~ drivers/spi/stm32_spi.c: In function 'stm32_spi_read_rxfifo': drivers/spi/stm32_spi.c:150:21: warning: comparison between signed and unsigned integer expressions [-Wsign-compare] (priv->rx_len >= sizeof(u32) || (sr & SPI_SR_RXWNE))) { ^~ drivers/spi/stm32_spi.c:156:21: warning: comparison between signed and unsigned integer expressions [-Wsign-compare] (priv->rx_len >= sizeof(u16) || ^~ drivers/core/simple-bus.c:15:12: warning: no previous prototype for 'simple_bus_translate' [-Wmissing-prototypes] fdt_addr_t simple_bus_translate(struct udevice *dev, fdt_addr_t addr) ^~~~~~~~~~~~~~~~~~~~ drivers/spi/stm32_spi.c: In function 'stm32_spi_set_speed': drivers/spi/stm32_spi.c:335:10: warning: comparison between signed and unsigned integer expressions [-Wsign-compare] div > STM32_MBR_DIV_MAX) ^ drivers/spi/stm32_spi.c:344:19: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits] if ((mbrdiv - 1) < 0) ^ drivers/spi/stm32_spi.c: In function 'stm32_spi_probe': drivers/spi/stm32_spi.c:531:16: warning: comparison between signed and unsigned integer expressions [-Wsign-compare] for (i = 0; i < ARRAY_SIZE(priv->cs_gpios); i++) { ^ Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12spi: stm32_qspi: avoid warnings when building with W=1 optionPatrick Delaunay
This patch solves warnings detected by setting W=1 when building. Warnings type detected: - [-Wtype-limits] - [-Wsign-compare] Signed-off-by: Christophe Kerello <christophe.kerello@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12mtd: rawnand: stm32_fmc2: avoid warnings when building with W=1 optionPatrick Delaunay
This patch solves warnings detected by setting W=1 when building. Warnings type detected: - [-Wsign-compare] - [-Wtype-limits] Signed-off-by: Christophe Kerello <christophe.kerello@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12power: stpmic1: Fix warnings when compiling with W=1Patrick Delaunay
This patch solves the following warnings: warning: this statement may fall through [-Wimplicit-fallthrough=] Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12pinctrl: pinctrl_stm32: Fix warnings when compiling with W=1Patrick Delaunay
This patch solves the following warnings: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits] if (*idx < 0) ^ drivers/pinctrl/pinctrl_stm32.c: At top level: warning: no previous prototype for 'stm32_pinctrl_probe' [-Wmissing-prototypes] int stm32_pinctrl_probe(struct udevice *dev) ^~~~~~~~~~~~~~~~~~~ Signed-off-by: Patrice CHOTARD <patrice.chotard@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12ram: stm32mp1_ram: Fix warnings when compiling with W=1Patrick Delaunay
This patch solves the following warnings: drivers/ram/stm32mp1/stm32mp1_ram.c: In function 'stm32mp1_ddr_clk_enable': warning: comparison between signed and unsigned integer expressions [-Wsign-compare] for (idx = 0; idx < ARRAY_SIZE(clkname); idx++) { ^ drivers/ram/stm32mp1/stm32mp1_ram.c: In function 'stm32mp1_ddr_setup': warning: comparison between signed and unsigned integer expressions [-Wsign-compare] for (idx = 0; idx < ARRAY_SIZE(param); idx++) { ^ Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12misc: stm32_fuse: Fix warnings when compiling with W=1Patrick Delaunay
This patch solves the following warnings: warning: no previous prototype for 'fuse_read' [-Wmissing-prototypes] int fuse_read(u32 bank, u32 word, u32 *val) ^~~~~~~~~ CC cmd/sf.o warning: no previous prototype for 'fuse_prog' [-Wmissing-prototypes] int fuse_prog(u32 bank, u32 word, u32 val) ^~~~~~~~~ warning: no previous prototype for 'fuse_sense' [-Wmissing-prototypes] int fuse_sense(u32 bank, u32 word, u32 *val) ^~~~~~~~~~ warning: no previous prototype for 'fuse_override' [-Wmissing-prototypes] int fuse_override(u32 bank, u32 word, u32 val) ^~~~~~~~~~~~~ Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12power: regulator: stm32: Fix warnings when compiling with W=1Patrick Delaunay
This patch solves the following warnings: drivers/power/regulator/stm32-vrefbuf.c: In function 'stm32_vrefbuf_set_value': warning: comparison between signed and unsigned integer expressions [-Wsign-compare] if (uV == stm32_vrefbuf_voltages[i]) { ^~ Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12clk: clk_stm32mp1: Fix warnings when compiling with W=1Patrick Delaunay
This patch solves the following warnings: drivers/clk/clk_stm32mp1.c: In function 'stm32mp1_clk_get_parent': warning: comparison between signed and unsigned integer expressions [-Wsign-compare] for (i = 0; i < ARRAY_SIZE(stm32mp1_clks); i++) ^ Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12i2c: stm32f7_i2c: Fix warnings when compiling with W=1Patrick Delaunay
This patch solves the following warnings: drivers/i2c/stm32f7_i2c.c: In function 'stm32_i2c_compute_solutions': warning: comparison between signed and unsigned integer expressions [-Wsign-compare] if (scldel < scldel_min) ^ warning: comparison between signed and unsigned integer expressions [-Wsign-compare] if (((sdadel >= sdadel_min) && ^~ warning: comparison between signed and unsigned integer expressions [-Wsign-compare] (sdadel <= sdadel_max)) && ^~ drivers/i2c/stm32f7_i2c.c: In function 'stm32_i2c_choose_solution': warning: comparison between signed and unsigned integer expressions [-Wsign-compare] if (clk_error < clk_error_prev) { ^ Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12gpio: stm32_gpio: Fix warnings when compiling with W=1Patrick Delaunay
This patch solves the following warnings: drivers/gpio/stm32_gpio.c: In function 'stm32_offset_to_index': : comparison between signed and unsigned integer expressions [-Wsign-compare] if (idx == offset) ^~ Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12adc: stm32: Fix warnings when compiling with W=1Patrick Delaunay
This patch solves the following warnings: drivers/adc/stm32-adc-core.c: In function 'stm32h7_adc_clk_sel': warning: comparison between signed and unsigned integer expressions [-Wsign-compare] for (i = 0; i < ARRAY_SIZE(stm32h7_adc_ckmodes_spec); i++) { ^ warning: comparison between signed and unsigned integer expressions [-Wsign-compare] for (i = 0; i < ARRAY_SIZE(stm32h7_adc_ckmodes_spec); i++) { ^ Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
2019-07-12adc: stm32-adc: Fix warnings when compiling with W=1Patrick Delaunay
This patch solves the following warnings: drivers/adc/stm32-adc.c: In function 'stm32_adc_chan_of_init': warning: comparison between signed and unsigned integer expressions [-Wsign-compare] if (num_channels > adc->cfg->max_channels) { ^ Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
2019-07-12mmc: stm32_sdmmc2: avoid warnings when building with W=1 optionPatrick Delaunay
This patch solves warnings detected by setting W=1 when building. Warnings type detected: - [-Wmissing-prototypes] - [-Wimplicit-fallthrough=] Signed-off-by: Christophe Kerello <christophe.kerello@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12serial: stm32: Fix warnings when compiling with W=1Patrick Delaunay
This patch solves the following warnings: drivers/serial/serial_stm32.c: In function 'stm32_serial_probe': warning: comparison of unsigned expression < 0 is always false [-Wtype-limits] if (plat->clock_rate < 0) { ^ Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12pmic: stpmic1: add support for SYSRESET_POWER_OFFPatrick Delaunay
Adds support for SYSRESET_POWER_OFF = PMIC power off used by command power off and introduced by commit 751fed426f87 ("sysreset: Add a way to find the last reset"). The driver use SYSRESET_POWER for the PMIC-level power cycle, with restart. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12stm32mp1: syscon: remove stgenPatrick Delaunay
Reduce difference with kernel Linux device tree. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-12sysreset: syscon: add support for power offPatrick Delaunay
The new type sysreset 'POWER_OFF', introduced by commit 751fed426f87 ("sysreset: Add a way to find the last reset") is only supported for "syscon-poweroff" compatible. For details see Linux binding: ./Documentation/devicetree/bindings/power/reset/syscon-poweroff.txt This patch removes the support of POWER_OFF for "syscon-reboot" and keeps only the COLD reset (for command reset support) and it introduces the compatible "syscon-poweroff" for the POWER_OFF case. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
generated by cgit (git 2.34.1) at 2025-01-09 17:55:47 +0000