| Age | Commit message (Collapse) | Author |
|---|
|
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
This patch fixes bugs in usbdcore*.c related to the use of devices
with multiple configurations.
The original code made mistakes about the meaning of configuration value and
configuration index, and the resulting off-by-one errors resulted in:
* SET_CONFIGURATION always selected the first configuration, no matter what
wValue is being passed.
* GET_DESCRIPTOR/CONFIGURATION always returned the descriptor for the first
configuration (index 0).
Signed-off-by: Harald Welte <laforge@openmoko.org>
Acked-by: Markus Klotzbuecher <mk@denx.de>
|
|
This patch fixes NAND related printf format warning. Those warnings are
now visible since patch dc4b0b38d4aadf08826f6c31270f1eecd27964fd
[Fix printf errors.] by Andrew Klossner has been applied. Thanks, this is
really helpful.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch moves the check, if a device should be skipped in PCI PNP
configuration into the function pci_skip_dev(). This function is defined
as weak so that it can be overwritten by a platform specific one if
needed. The check if the device should get printed in the PCI summary upon
bootup (when CONFIG_PCI_SCAN_SHOW is defined) is moved to the function
pci_print_dev() which is also defined as weak too.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
|
|
This PCI-X e1000 variant works by just adding in the correct
PCI IDs in the appropriate places.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Round the serial port clock divisor value returned by
calc_divisor().
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Signed-off-by: John Roberts <john.roberts@pwav.com>
|
|
This is particularly problematic now that non-NAND-specific code is
including <nand.h>, and thus all debugging code is being compiled
regardless of whether it was requested, as reported by Scott McNutt
<smcnutt@psyent.com>.
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
This makes it easier to use the driver on other platforms.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Jean-Chritophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
In order to consolidate more of the various MMC drivers around the
tree, we must first have a common place to put them.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: Jean-Chritophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
|
|
|
|
As pointed out by Jerry Hicks, this patch corrects the device ID of
the Spansion AM29DL800BB NOR device. Verified against latest Spansion
datasheet (rev C4 from Dezember 2006).
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Remove duplicate definitions in include/lxt971a.h.
Remove duplicate registers and bits definitions in
include/lxt971a.h for standard MII registers, and
use values in include/miiphy.h instead.
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
Renesas SH7763 has 2 channel Ethernet device.
This is 10/100/1000 Base support.
But this patch check 10/100 Base only.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
|
|
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
|
|
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
If enable DEBUG, can not compile ne2000 driver.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
The driver need wait for the device updating signature to host.
If we don't wait for it, the driver can not detect the device(disk)
when the system powers up.
Signed-off-by: Dave Liu <daveliu@freescale.com>
|
|
Signed-off-by: Stuart Wood <stuart.wood@labxtechnologies.com>
|
|
Signed-off-by: Tor Krill <tor@excito.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
This patch simplifies flash_toggle() (AMD commandset), which is used to
detect if a FLASH device is still busy with erase/program operations. On
800MHz Canyonlands/Glacier boards (460EX/GT) the current implementation
did not detect the busy state reliably, resulting in non erased sectors
etc. This patch now simplifies this function by "just" comparing the
complete data-word instead of ANDing it with the command-word (0x40)
before the compatison. It is done the same way in the Linux implementation
chip_ready() in cfi_cmdset_0002.c.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
|
|
|
|
|
|
|
|
|
|
LAWs have the concept of priority so its useful to be able to allocate
the lowest (highest number) priority. We will end up using this with the
new DDR code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Make it so we keep track of which LAWs have allocated and provide
a function (set_next_law) which can allocate a LAW for us if one is
free.
In the future we will move to doing more "dynamic" LAW allocation
since the majority of users dont really care about what LAW number
they are at.
Also, add CONFIG_MPC8540 or CONFIG_MPC8560 to those boards which needed them
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
|
|
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
|
|
This patch adds basic support for the TQM8548 module from TQ-Components
(http://www.tqc.de/) including DDR2 SDRAM initialisation and support for
eTSEC 3 and 4
Furthermore Flash buffer write has been enabled to speed up output to
the Flash by approx. a factor of 10.
Signed-off-by: Thomas Waehner <thomas.waehner@tqs.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
|
|
This is a re-write of the NAND FSL UPM driver using the more universal
hwcontrol callback (instead of the cmdfunc callback). Here is a brief
list of furher modifications:
- For the time being, the UPM setup writing the UPM array has been
removed from the driver and must now be done by the board specific
code.
- The bus width definition in "struct fsl_upm_nand" is now in bits to
comply with the corresponding Linux driver and 8, 16 and 32 bit
accesses are supported.
- chip->dev_read is only set if fun->dev_ready != NULL, which is
required for boards not connecting the R/B pin.
- A few issue have been fixed with MxMR bit manipulation like in the
corresponding Linux driver.
Note: I think the "io_addr" field of "struct fsl_upm" could be removed
as well, because the address is already determined by
"nand->IO_ADDR_[RW]", but I'm not 100% sure.
This patch has been tested on a TQM8548 modules with the NAND chip
Micron MT29F8G08FABWP.
This patch is based on the following patches posted to this list a few
minutes ago:
PPC: add accessor macros to clear and set bits in one shot
83xx/85xx/86xx: add more MxMR local bus definitions
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
|
|
Replace COBJS-y with appropriate driver config names.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
This was configured to use the deprecated CONFIG_OF_FLAT_TREE, change
to CONFIG_OF_LIBFDT.
WARNING: This conversion is untested because I do not have a board to
test it on.
NOTE: The FDT blob (DTS) must have an /aliases/ethernet0 and (optionally)
/aliases/ethernet1 property for the ethernet to work.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
|
|
SH7763 has 3 SCIF channels. SCIF0 and 1 are same register constitution,
but only SCIF2 is different. This patch work all SCIF channel.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
|
|
According to the Application Notes of the DM9000, only the 2 bits 0:1 of
the status byte need to be checked to identify a valid packet in the fifo
But, The several different Application Notes do not all speak the same
language on these bits. They do not disagree, but only 1 Application Note
noted explicitly that only these 2 bits need to be checked.
Even the datasheets do not mention anything about these 2 bits.
Because the old code, and the kernel check the whole byte, I left this piece
untouched.
However, I tested all board/DM9000[A|E|EP] devices with this 2 bit check, so
it should work.
Notice, that the 2nd iteration through this receive loop (when a 2nd packet is
in the fifo) is much shorter now, compared to the older U-boot driver code,
so that we can maybe run into a hardware condition now that was never seen
before, or maybe was seen very unfrequently.
Additionaly added a cleanup of a stack variable.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
- Fix traditional KSEG names
- Replace PHYSADDR with CPHYSADDR
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
|
|
A last minute cleanup before submitting the DM9000A patch series yesterday introduced
a bug in reading the rx-status registers in 32bit mode only.
This patch repairs this.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
Some lines of the U-boot DM9000x driver are longer than 80 characters, or
need some other minor cleanup.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
The DM9000A network controller does not work with the U-boot DM9000x driver.
Analysis showed that many incoming packets are lost.
The DM9000A Application Notes V1.20 (section 5.6.1) recommend that the poll to
check for a valid rx packet be done on the interrupt status register, not
directly by performing the dummy read and the rx status check as is currently
the case in the u-boot driver.
When the recommended poll is done as suggested the driver starts working
correctly on 10Mbit/HD, but on 100MBit/FD packets come in faster so that there
can be more than 1 package in the fifo at the same time.
The driver must perform the rx-status check in a loop and read and handle all
packages until there is no more left _after_ the interrupt RX flag is set.
This change has been tested with DM9000A, DM9000E, DM9000EP.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
According to the application notes of the DM9000 v1.22 chapter 5.2 bullet 2, the
reset procedure must be done twice to properly reset the DM9000 by means of software.
This errata is not needed anymore for the DM9000A, but it does not bother it.
This change has been tested with DM9000A, DM9000E, DM9000EP.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
The eth_send routine of the U-boot DM9000x driver does not match the
DM9000 or DM9000A application notes/programming guides.
This change improves the stability of the DM9000A network controller.
This change has been tested with DM9000A, DM9000E, DM9000EP.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
