summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2014-11-07drivers/net/uli526x.c: fix syntax errorWolfgang Denk
Fix error detected by cppcheck: [drivers/net/uli526x.c:551]: (error) printf format string requires 3 parameters but only 2 are given. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Roy Zang <tie-fei.zang@freescale.com>
2014-11-07power_spi.c: Rewrite pmic_reg functionTom Rini
The pmic_spi_free function isn't ever used, and as the frameworks stand today, cannot be, so remove it. Integrate the probe function into pmic_reg as it's not really a "probe" today. Finally, add an err label for the common failure cases. Cc: Lukasz Majewski <l.majewski@samsung.com> Cc: Przemyslaw Marczak <p.marczak@samsung.com> Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Stefano Babic <sbabic@denx.de>
2014-11-07net: smc911x: Keep MAC programmedMarek Vasut
Make sure to keep the MAC address programmed in the SMC911x ADDRH and ADDRL registers. Linux can read those registers to determine the MAC address on EEPROM-less configurations. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Tom Rini <trini@ti.com>
2014-11-07sort drivers/mmc/MakefilePavel Machek
Sort drivers/mmc makefile, as requested by wd. Signed-off-by: Pavel Machek <pavel@denx.de> Acked-by: Chin Liang See <clsee@altera.com>
2014-11-07Merge git://git.denx.de/u-boot-tiTom Rini
2014-11-06omap: hsmmc: assume cd gpio is active lowIgor Grinberg
Switch the default CD GPIO polarity to active low. The current hsmmc driver assumption that the CD GPIO is active high, but in the real hardware, usually the opposite holds. The usual SD card socket has a mechanical switch which is grounded as soon as a card is inserted. Of course there might be some board logic which inverts the signal, but as far as current users are concerned, there is no such logic. Current U-Boot users either not using the CD functionality, or have a different way (e.g. external to SoC GPIO controller) for checking the card presence. This patch also brings the polarity assumption in line with the Linux kernel and adds appropriate comments. This patch also might spare issues once the TWL GPIO driver will be converted to the DM. Signed-off-by: Igor Grinberg <grinberg@compulab.co.il> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Cc: Dmitry Lifshitz <lifshitz@compulab.co.il> Reviewed-by: Tom Rini <trini@ti.com>
2014-11-06dma: keystone_nav: remove spurious qm_cfg verificationKhoronzhuk, Ivan
The verification qm_cfg existence is done at ksnav_init(). So, there is no need to verify it after initialization. Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2014-11-06net: phy: marvell: add errata w/a for 88E151* chipsHao Zhang
As per Marvell Release Notes - Alaska 88E1510/88E1518/88E1512/88E1514 Rev A0, Errata Section 3.1 Marvell PHY has an errata which requires that certain registers get written in order to restart autonegotiation. Signed-off-by: Hao Zhang <hzhang@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com> Reviewed-by: Stefan Roese <sr@denx.de>
2014-11-05net: keystone_net: add Keystone2 K2L SoC supportKhoronzhuk, Ivan
The Keystone2 Lamar SoC uses the same keystone net driver. This patch adds opportunity to use it by K2L SoCs. Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-11-05net: keystone_serdes: add keystone K2L SoC supportKhoronzhuk, Ivan
Keystone2 Lamar SoC uses the same keystone SerDes driver. All Keystone2 EVM boards currently use SerDes driver, so move CONFIG_TI_KEYSTONE_SERDES to common configuration file. Acked-by: Murali Karicheri <m-karicheri2@ti.com> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-11-05Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini
2014-11-05Merge git://www.denx.de/git/u-boot-sunxiTom Rini
2014-11-05dm: sunxi: Request USB vbus gpioHans de Goede
This is necessary for the device-model enabled builds to work properly. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Simon Glass <sjg@chromium.org>
2014-11-05dm: sunxi: Request card detect gpioHans de Goede
This is necessary for the device-model enabled builds to work properly. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Simon Glass <sjg@chromium.org>
2014-11-05dm: sunxi: Add support for serial using driver modelSimon Glass
Add a driver for the designware serial UART used on sunxi. This just redirects to the normal ns16550 driver. Add a stdout-path to the device tree so that the correct UART is chosen. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-11-05dm: sunxi: Modify the GPIO driver to support driver modelSimon Glass
This adds driver model support to the sunxi GPIO driver, using the device tree to trigger binding of the driver. The driver will still operate without driver model too. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-11-05sunxi: Use CONFIG_MACH_SUN?I from Kconfig instead of CONFIG_SUN?IIan Campbell
Mostly automatic with: sed -i -e 's/CONFIG_\(SUN[45678]I\)/CONFIG_MACH_\1/g' $(git grep -l CONFIG_SUN[45678]I) followed by removing the relevant #defines from include/configs/sun?i.h by hand. Signed-off-by: Ian Campbell <ijc@hellion.org.uk> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-11-04Merge git://git.denx.de/u-boot-shTom Rini
2014-11-04serial: add prototypes for init functionsJeroen Hofstee
While at it, sort them. Cc: Tom Rini <trini@ti.com> Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-11-04i2c: use __weakJeroen Hofstee
Cc: Heiko Schocher <hs@denx.de> Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-11-04Merge branch 'agust@denx.de' of git://git.denx.de/u-boot-stagingTom Rini
2014-11-04usb: ehci: rmobile: Collect up address dataNobuhiro Iwamatsu
R8A7791, R8A7793 and R8A7794 have same IP of USB controller. This collect up address data of each SoCs. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-11-04usb: ehci: rmobile: Add support R8A7793Nobuhiro Iwamatsu
R8A7793 has same IP of USB controller as R8A7791 and R8A7794 of rmobile ARM SoCs. This adds support R8A7793 to EHCI HCD of rmobile. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
2014-11-04usb: Make pollable int support available outside of ehci-hcd.cHans de Goede
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-11-04usb: ehci: Move cache invalidation to poll_int_queueHans de Goede
Preperation patch to use poll_int_queue outside of ehci-hcd.c . Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-11-04usb: ehci: Move interrupt packet length check to create_int_queueHans de Goede
Preperation patch to use create_int_queue outside of ehci-hcd.c . Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-11-04usb: ehci: Do not disable an already disabled periodic scheduleHans de Goede
When periodic_schedules == 0, the schedule is disabled and there is no reason to disable it again. Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-11-04net: sh-eth: Add cache writeback control after setting bit of DMA descriptorNobuhiro Iwamatsu
A bit field of DMA descriptor is on memory area of DMA. If we set data to bit of DMA descriptor, we must be writeback data of DMA descriptor. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-11-04net: sh-eth: Use memalign instead of orignal memroy alignment functionNobuhiro Iwamatsu
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-11-04net: sh-eth: Remove definition of RX_DESC_SIZE and TX_DESC_SIZENobuhiro Iwamatsu
RX_DESC_SIZE and TX_DESC_SIZE mean the size of the data descriptor for sh-eth. We can acquire this in sizeof. It is not necessary to define these in define. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-11-04serial: sh: r8a7794: Add support external clockNobuhiro Iwamatsu
The baud rate setting of external clock is enabled. Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-11-04net: sh-eth: Add support R8A7793Nobuhiro Iwamatsu
R8A7793 has the same sh-ether IP core as other SH/rmobile. This patch adds support of R8A7793. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-11-04serial: sh: Add support R8A7793Nobuhiro Iwamatsu
This adds the preset value to register for R8A7793. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2014-11-03Merge branch 'master' of git://git.denx.de/u-boot-uniphierTom Rini
2014-11-03Merge branch 'master' of git://git.denx.de/u-boot-spiTom Rini
2014-10-31twl4030: VMMC2 3.2V enable on MMC initPaul Kocialkowski
This enables the VMMC2 LDO, which powers the MMC2 device. When the device starts from MMC2, this has already been enabled by the BootROM, but when starting from peripheral boot (USB, UART), it is not the case. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-10-30mtd: nand: mxs: Add ECC geometry for 2048b/112b NANDMarek Vasut
Add ECC geometry for NAND which has 2048b pagesize and 112b OOB size. This is for example Macronix MX30LF2G28AB chip. Signed-off-by: Marek Vasut <marex@denx.de>
2014-10-29serial: UniPhier: add static to locally used functionsMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-10-29serial: UniPhier: add .pending handlerMasahiro Yamada
Without .pending handler, tstc() function always returns 1. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-10-29i2c: designware: Convert driver to multibus/multiadapter frameworkStefan Roese
In preparation for the SoCFPGA support of the designware I2C driver, convert this driver to the common CONFIG_SYS_I2C framework. This patch converts all users of this driver, this is: - ST spearxxx boards - AXS101 (ARC700 platform) I couldn't test this patch on those boards. Only compile tested for all spear boards. And tested on SoCFPGA. Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Marek Vasut <marex@denx.de> Acked-by: Alexey Brodkin <abrodkin@synopsys.com> Tested-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Heiko Schocher <hs@denx.de> Cc: Vipin Kumar <vk.vipin@gmail.com> Cc: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-29i2c: mxs: Add support for I2C 1 on i.MX28Marek Vasut
Add support for I2C bus 1 on the i.MX28. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Heiko Schocher <hs@denx.de>
2014-10-29i2c: mxs: Pass the i2c_adapter aroundMarek Vasut
This patch permeates the struct i2c_adapter throughout the driver, so that it can be used to determine which adapter should be used. Note that the driver still supports only one adapter. Note that the patch does shuffle mxs_i2c_set_bus_speed() to the top of the driver, but the function remains unchanged. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Heiko Schocher <hs@denx.de>
2014-10-29i2c: mxs: Add basic support for i2c frameworkMarek Vasut
This patch just converts the function prototypes used throughout this driver to match those of the i2c framework. There is so far no functional change. This patch does not do the deeper integration of the framework bits. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Heiko Schocher <hs@denx.de>
2014-10-29i2c: mxs: Consolidate hard-coded bus addressMarek Vasut
This patch prepares the MXS I2C driver for the conversion to the new I2C driver framework by pulling out the hard-coded I2C0 address from all the places. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Heiko Schocher <hs@denx.de>
2014-10-28dwc_ahsata: use bitwise operator in sata_port_statusNikita Kiryanov
The logic of the return statement in sata_port_status() calls for a bitwise 'AND' operator, not logical 'AND'. Fix the typo. Reported-by: Jeroen Hofstee <jeroen@myspectrum.nl> Cc: Jeroen Hofstee <jeroen@myspectrum.nl> Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2014-10-28Merge git://git.denx.de/u-boot-dmTom Rini
2014-10-28e1000: add i211 and unprogrammed i210/i211 supportMarcel Ziswiler
This patch adds support for i211 as well as unprogrammed aka tools only i210/i211 chip support. Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
2014-10-27mmc: s5p: set SD detection pin as inputPrzemyslaw Marczak
The SD Card slot detection pin should be configured as input. Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Acked-by: Simon Glass <sjg@chromium.org>
2014-10-27e1000: fix sw fw sync on igb i210/i211Marcel Ziswiler
I finally had a look at the datasheet and spotted an additional register address difference between regular E1000 and i210/i211 chips. This patch fixes this and now successfully works on programmed i210/i211 as well as unprogrammed i211. Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
2014-10-27net/e1000: Fix EEPROM access errorYork Sun
Commit 951860634fdb557bbb58e0f99215391bc0c29779 may have changed the logic unintentially from "if (!(swfw_sync & (fwmask | swmask)))" to "if ((swfw_sync & swmask) && !(swfw_sync & fwmask))". This change breaks some e1000 NIC with a message "ERROR: Unable to read EEPROM!". Signed-off-by: York Sun <yorksun@freescale.com> CC: Marek Vasut <marex@denx.de> CC: Tim Harvey <tharvey@gateworks.com> Acked-by: Marcel Ziswiler <marcel@ziswiler.com>
generated by cgit (git 2.34.1) at 2024-12-27 05:17:43 +0000