summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2011-04-12sf: localize erase funcsMike Frysinger
No need for these to be exported as they are only accessed indirectly via function pointers. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-12sf: sst: setup read funcMike Frysinger
The previous unification patch missed setting up the sst read func. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-12sf: add struct spi_flash.sector_size parameterRichard Retanubun
This patch adds a new member to struct spi_flash (u16 sector_size) and updates the spi flash drivers to start populating it. This parameter can be used by spi flash commands that need to round up units of operation to the flash's sector_size. Having this number in one place also allows duplicated code to be further collapsed into one common location (such as erase parameter and the detected message). Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-11sf: atmel: undo unification of status pollingMike Frysinger
The AT45 flashes are completely different (at the command set and status register level) from all other SPI flashes, so we can't unify their logic with common code. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-11ftwdt010_wdt: support faraday ftwdt010 watchdogMacpaul Lin
Faraday ftwdt010 watchdog is an architecture independant watchdog. It is usually used in SoC chip design. Signed-off-by: Macpaul Lin <macpaul@andestech.com> Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-04-11Net: Add Intel E1000 82574L PCIe card supportRoy Zang
Add Intel E1000 82574L PCIe card support. Test on MPC8544DS and MPC8572 board. Add the missing contact information for future support. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Acked-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-11ea20: fix undefined PHY_* errorsBen Gardiner
This patch fixes ea20 after 8ef583a0351590a91394499eb5ca2ab8a703d959 where the u-boot custom PHY_ macros were replaced with those of linux/mii.h MII_ definitions except in the RMII support for davinci_emac. Probably also due to the merge path of changes in 2010.12. Signed-off-by: Ben Gardiner<bengardiner@nanometrics.ca> CC: Mike Frysinger <vapier@gentoo.org> Acked-by: Mike Frysinger <vapier@gentoo.org>
2011-04-11sf: unify read functionsMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-11sf: unify erase functionsMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-11sf: unify status polling for ready bitMike Frysinger
All of the spi flash drivers implement the status register polling for detecting the device ready state, so unify them all in a new helper function -- spi_flash_wait_ready. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-11sf: unify read/write helpersMike Frysinger
These functions largely do the same exact thing, so unify them all into one basic function. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-10Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk
2011-04-10Merge branch 'master' of git://git.denx.de/u-boot-blackfinWolfgang Denk
2011-04-10fsl_esdhc: Deal with watermark level register related changesPriyanka Jain
P1010 and P1014 has v2.3 version of FSL eSDHC controller in which watermark level register description has been changed: 9-15 bits represent WR_WML[0:6], Max value = 128 represented by 0x00 25-31 bits represent RD_WML[0:6], Max value = 128 represented by 0x00 Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com> Tested-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-08Blackfin: bfin_sdh: add support for multiblock operationsSonic Zhang
Don't forget to count full data size for the multiblock operation request. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: bfin_sdh: set all timer bits before transferCliff Cai
The timer register is 32bits, not 16bit, so 0xFFFF won't fill it. Write out -1 to make sure to fill the whole thing. Signed-off-by: Cliff Cai <cliff.cai@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-08Blackfin: BF50x: new processor portMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-07mtd, cfi: introduce void flash_protect_default(void)Heiko Schocher
collect code which protects default sectors in a function, called flash_protect_default. So boardspecific code can call it too. Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2011-04-07cfi_flash: use AMD fixups for AMIC (e.g. A29L160A series) tooMario Schuknecht
Signed-off-by: Mario Schuknecht <m.schuknecht@dresearch.de> Signed-off-by: Steffen Sledz <sledz@dresearch.de> Signed-off-by: Stefan Roese <sr@denx.de>
2011-04-05powerpc/85xx: Add P1021 specific QE and UEC supportHaiying Wang
P1021 has some QE pins which need to be set in pmuxcr register before using QE functions. In this patch, pin QE0 and QE3 are set for UCC1 and UCC5 in Eth mode. QE9 and QE12 are set for MII management. QE12 needs to be released after MII access because QE12 pin is muxed with LBCTL signal. Also added relevant QE support defines unique to P1021. The P1021 QE is shared on P1012, P1016, and P1025. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-05Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk
Conflicts: drivers/usb/host/ehci-pci.c Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-04-04tsec: add AR8021 PHY supportLi Yang
Signed-off-by: Li Yang <leoli@freescale.com>
2011-04-04echi: add ULI1575 PCI IDZhao Chenhui
Add ULI1575 EHCI controller to the list of the supported devices. Signed-off-by: Zhao Chenhui <b35336@freescale.com> Acked-by: Remy Bohmer <linux@bohmer.net> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04powerpc/8xxx: Fix LAW init to respect pre-initialized entriesKumar Gala
If some pre-boot or earlier stage bootloader (NAND SPL) has setup LAW entries consider them good and mark them used. In the NAND SPL case we skip re-initializing based on the law_table since the SPL phase already did that. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04fsl_pci: Add support for FSL PCIe controllers v2.xPrabhakar Kushwaha
FSL PCIe controller v2.1: - New MSI inbound window - Same Inbound windows address as PCIe controller v1.x Added new pit_t member(pmit) to struct ccsr_pci for MSI inbound window FSL PCIe controller v2.2 and v2.3: - Different addresses for PCIe inbound window 3,2,1 - Exposed PCIe inbound window 0 - New PCIe interrupt status register Added new Interrupt Status register to struct ccsr_pci & updated pit_t array size to reflect the 4 inbound windows. To maintain backward compatiblilty, on V2.2 or greater controllers we start with inbound window 1 and leave inbound 0 with its default value (which maps to CCSRBAR). Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-02ehci-pci: Add PCI EHCI controllerTrübenbach, Ralf
This patch adds support for the PI7C9X442SL PCIe EHCI host controller from Pericom. Tested at P4080DS eval board from Freescale. Signed-off-by: Ralf Trübenbach <ralf.truebenbach@men.de> Cc: Remy Bohmer <linux@bohmer.net>
2011-04-02usb: musb: blackfin: check anomaly workarounds at runtime tooMike Frysinger
The anomaly workarounds we need for older silicon might break things if used on newer versions where the anomalies don't exist. So check the silicon rev at runtime too. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-02usb: musb: blackfin: make clkin configurableMike Frysinger
Not everyone has a 24MHz clkin to the USB, so let board porters override. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-04-01atmel_nand: don't require CONFIG_SYS_NAND_ENABLE_PINmichael
If NCE is hooked up to NCS3, we don't need to (and can't) explicitly set the state of the NCE pin. Instead, the controller asserts it automatically as part of a command/data access. Only "CE don't care"-type NAND chips can be used in this manner. Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Cc: Scott Wood <scottwood@freescale.com> Cc: Reinhard Meyer <u-boot@emk-elektronik.de>
2011-04-01NAND: add support for reading ONFI page tableFlorian Fainelli
This patch adds support for reading an ONFI page parameter from a NAND device supporting it. If this is the case, struct nand_chip onfi_version member contains the supported ONFI version, 0 otherwise. This allows NAND drivers past nand_scan_ident to set the best timings for the NAND chip. Signed-off-by: Florian Fainelli <florian@openwrt.org> Signed-off-by: Scott Wood <scottwood@freescale.com>
2011-04-01NAND: add more watchdog resetsScott Wood
Poke the watchdog in a variety of looping constructs, which could take a long time to complete. Signed-off-by: Scott Wood <scottwood@freescale.com>
2011-03-31Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk
2011-03-29powerpc/85xx: Handle PCIe initialization requires for P1021 class SoCsPrabhakar Kushwaha
The P1011, P1012, P1015, P1016, P1020, P1021, P1024, & P1025 SoCs require that we initialize the SERDES registers if the lanes are configured for PCIe. Additionally these devices PCIe controller do not support ASPM and we have to explicitly disable it. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-03-28cfi_flash: fix bug with flash banks with different sector numbersMartin Krause
The function find_sector() does not take into account if the flash bank has changed since the last call. This could lead to illegal accesses inside and beyond the flash_info_t info strcture. For example if the current flash bank has less sectors than the last used flash bank. This patch adds two cheks. One that insures, that the current sector does not exceed the allowed maximum (which is always a good idea). And one that checks if the current access is to the same flash bank as the last access. If not, the search loop will start with sector 0. Signed-off-by: Martin Krause <martin.krause@tqs.de> Signed-off-by: Stefan Roese <sr@denx.de>
2011-03-27Coding Style cleanup: remove trailing empty linesWolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-03-27S5P: mmc: Resolved interrupt error during mmc_initChander Kashyap
Blocksize was hardcoded to 512 bytes. But the blocksize varies depeding on various mmc subsystem commands (between 8 and 512). This hardcoding was resulting in interrupt error during data transfer. It is now calculated based upon the request sent by mmc subsystem. Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2011-03-21net: ftmac100: update get_timer() usagesPo-Yu Chuang
Use get_timer() the same way as drivers/net/ftgmac100.c Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com> Reviewed-by: Macpaul Lin <macpaul@gmail.com> Tested-by: Macpaul Lin <macpaul@gmail.com>
2011-03-21net: ftmac100: remove unnecessary volatilesPo-Yu Chuang
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com> Reviewed-by: Macpaul Lin <macpaul@gmail.com> Tested-by: Macpaul Lin <macpaul@gmail.com>
2011-03-16net: sh_eth: add support for SH7757's ETHERYoshihiro Shimoda
SH7757 has ETHER and GETHER. This patch supports EHTER only. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2011-03-07fsl_esdhc: Correcting esdhc timeout counter calculationPriyanka Jain
- Timeout counter value is set as DTOCV bits in SYSCTL register For counter value set as timeout, Timeout period = (2^(timeout + 13)) SD Clock cycles - As per 4.6.2.2 section of SD Card specification v2.00, host should cofigure timeout period value to minimum 0.25 sec. - Number of SD Clock cycles for 0.25sec should be minimum (SD Clock/sec * 0.25 sec) SD Clock cycles = (mmc->tran_speed * 1/4) SD Clock cycles - Calculating timeout based on (2^(timeout + 13)) >= mmc->tran_speed * 1/4 Taking log2 both the sides and rounding up to next power of 2 => timeout + 13 = log2(mmc->tran_speed/4) + 1 Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com> Acked-by: Mingkai Hu <Mingkai.Hu@freescale.com> Tested-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-22fsl_law: Fix LAW printing functionKumar Gala
We had an extra '0x' in the output of the LAWAR header that would cause output like: LAWBAR11: 0x00000000 LAWAR0x11: 0x80f0001d intead of: LAWBAR11: 0x00000000 LAWAR11: 0x80f0001d Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-21mvmfp: add MFP configuration support for PANTHEONLei Wen
This patch adds the Multiple Function Pin configuration support for Marvell PANTHEON SoCs Signed-off-by: Lei Wen <leiwen@marvell.com>
2011-02-21serial: add pantheon soc supportLei Wen
Signed-off-by: Lei Wen <leiwen@marvell.com>
2011-02-21serial: Add Tegra2 serial port supportTom Warren
Signed-off-by: Tom Warren <twarren@nvidia.com>
2011-02-19USB-RNDIS: Send RNDIS state on disconnectingVitaly Kuzmichev
Add waiting for receiving Ethernet gadget state on the Windows host side before dropping pullup, but keep it for debug. Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
2011-02-19USB: Add USB RNDIS gadget protocolVitaly Kuzmichev
Port USB gadget RNDIS protocol support from linux-2.6.26 (.27 gadget stack actually has composite drivers). Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
2011-02-19USB-CDC: Move struct declaration before its useVitaly Kuzmichev
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
2011-02-19USB-CDC: Port struct net_device_statsVitaly Kuzmichev
Port struct net_device_stats and statistics collecting needed for RNDIS protocol. Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
2011-02-19USB-CDC: handle interrupt after dropped pullupVitaly Kuzmichev
Disconnecting USB gadget with pending interrupt may cause its wrong handling in the next time when interface will be started again (especially actual for RNDIS). This interrupt may force the gadget to queue unexpected response before setup stage. Despite the fact that such interrupt handled after dropped pullup also may add pending response, this will not bring to any issues due to usb_ep_disable (which clears the queue) called on gadget unregistering. Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
2011-02-19Add support for ASIX AX88772 USB 2.0 10/100Mbit Ethernet AdaptorSimon Glass
Driver originally written by NVIDIA Corporation, modified to handle odd-length packets. Signed-off-by: Simon Glass <sjg@chromium.org>
generated by cgit (git 2.34.1) at 2024-12-29 20:15:36 +0000