summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2020-01-16clk: mediatek: add configurable pcw_chg_reg/ibits/fmin to mtk_pllmingming lee
Add configurable pcw_chg_reg/ibits/fmin to mtk_pll to support mt8512
2020-01-16clk: mediatek: add set_clr_upd mux type flowmingming lee
Add new set_clr_upd mux type and related operation to mtk common clock driver to support mt8512
2020-01-16clk: mediatek: add driver support for MT8512mingming lee
Add clock driver for MediaTek MT8512 SoC, include topckgen, apmixedsys and infracfg support. Signed-off-by: mingming lee <mingming.lee@mediatek.com>
2020-01-16mmc: config help typo fixJoel Johnson
Fix typo in description of MMC_QUIRKS config option. Signed-off-by: Joel Johnson <mrjoel@lixil.net>
2020-01-16mmc: add additional quirk for APP_CMD retryJoel Johnson
It was observed (on ClearFog Base) that sending MMC APP_CMD returned an error on the first attempt. The issue appears to be timing related since even inserting a puts() short debug entry before the execution added sufficient delay to receive success on first attempt. Follow the existing quirks pattern to retry if initial issuance failed so as to not introduce any delay unless needed. Signed-off-by: Joel Johnson <mrjoel@lixil.net>
2020-01-16Drop CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK usageYangbo Lu
The eSDHC reference clocks should be provided by speed.c in arch/. And we do not need CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK option to select which clock to use. Because we can make the driver to select the periperhal clock which is better (provides higher frequency) automatically if its value is provided by speed.c. This patch is to drop this option and make driver to select clock automatically. Also fix peripheral clock calculation issue in fsl_lsch2_speed.c/fsl_lsch3_speed.c. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-01-16mmc: fsl_esdhc: drop useless fdt fixupYangbo Lu
The fdt fixup for properties "peripheral-frequency" and "adapter-type" was once for a Freescale SDK release. The properties haven't been existed in linux mainline. Drop these useless code. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-01-16mmc: fsl_esdhc_imx: drop QorIQ eSDHC specific peripheral clock codeYangbo Lu
Drop QorIQ eSDHC specific peripheral clock code. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
2020-01-15Add dependencies for MALLOC_F and OF_LIBFDTSean Anderson
Some features implicitly depended on MALLOC_F and OF_LIBFDT and would fail at link-time if these features were not enabled. Signed-off-by: Sean Anderson <seanga2@gmail.com>
2020-01-15Kconfig: Rename CONFIG_SPL_DMA_SUPPORT to CONFIG_SPL_DMAVignesh Raghavendra
Rename CONFIG_SPL_DMA_SUPPORT to CONFIG_SPL_DMA. This allows to use macros such as CONFIG_IS_ENABLED() that allow conditional compilation of code for SPL and U-Boot. Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-01-14mmc: fsl_esdhc: add compatible for fsl, imxrt-usdhcGiulio Benetti
Add compatible "fsl,imxrt-usdhc" to make mmc working on i.MXRT platforms with CONFIG_DM_MMC=y. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2020-01-14mmc: fsl_esdhc: make if(CONFIG_IS_ENABLED(CLK)) an #if statementGiulio Benetti
Not all architectures(i.e. i.MXRT) support mxc_get_clock() and use DM_CLK instead. So building could result in failure due to missing mxc_get_clock(). Make if(CONFIG_IS_ENABLED(CLK)) an #if statement. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2020-01-14ram: add SDRAM driver for i.MXRT SoCsGiulio Benetti
Add SDRAM driver for i.MXRT SoCs. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2020-01-14serial_lpuart: add support for i.MXRTGiulio Benetti
Add i.MXRT compatible string and cpu type support to lpuart driver, to use little endian 32 bits configurations. Also according to RM, the Receive RX FIFO Enable (RXFE) field in LPUART FIFO register is bit 3, so this definition should change to 0x08 as done for i.MX8. It needs also to set baudrate the same way as i.MX8 does. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2020-01-14serial_lpuart: add clock enable if CONFIG_CLK is definedGiulio Benetti
This driver assumes that lpuart clock is already enabled before probing but using DM only lpuart won't be automatically enabled so add clk_enable() when probing if CONFIG_CLK is defined. If clock is not found, because DM is not used, let's emit a warning and proceed, because serial clock could also be already enabled by non DM code. If clock is found but cna't be enabled then return with error. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2020-01-14gpio: mxc_gpio: add support for i.MXRT1050Giulio Benetti
Add i.MXRT1050 support, there are 5 GPIO banks. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2020-01-14pinctrl: add i.MXRT driverGiulio Benetti
Add i.MXRT pinctrl driver. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2020-01-14clk: imx: add i.IMXRT1050 clk driverGiulio Benetti
Add i.MXRT1050 clk driver support. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2020-01-14clk: imx: pfd: add set_rate()Giulio Benetti
Implement set_rate() for pfd. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2020-01-14clk: imx: pllv3: add support for PLLV3_AV typeGiulio Benetti
Add support for PLLV3 AV type. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2020-01-14clk: imx: pllv3: add PLLV3_SYS supportGiulio Benetti
Add PLLV3_SYS support by adding set/get_rate() for PLLV3_SYS but keeping generic enable()/disable(). Add a different driver because ops are different respect to GENERIC/USB. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2020-01-14clk: imx: pllv3: add set_rate() supportGiulio Benetti
Add generic set_rate() support. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2020-01-14clk: imx: pllv3: add disable() supportGiulio Benetti
Add disable() support. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2020-01-14clk: imx: pllv3: add enable() supportGiulio Benetti
Before set_rate() pllv3 needs enable() to power the pll up. Add enable() taking into account different power_bit and different powerup_set, because some pll needs its power_bit to be set or reset to be powered on. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2020-01-14clk: imx: pllv3: set div_mask differently if PLLV3 is GENERIC or USBGiulio Benetti
div_mask is different for GENERIC and USB pll, so set it according. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2020-01-14clk: imx: pllv3: register PLLV3 GENERIC and USB as 2 different clocksGiulio Benetti
Better to register the 2 clock as 2 different drivers because they work slightly differently depending on power_bit and powerup_set bits coming on next patches. Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2020-01-14clk: imx8qxp: extend to support getting I2C IPG clockAnatolij Gustschin
Since commit d02be21d3004 ("i2c: imx_lpi2c: add ipg clk") getting I2C clocks doesn't work. Add I2C IPG clock IDs to related switch statements to fix it. Signed-off-by: Anatolij Gustschin <agust@denx.de> Cc: Lukasz Majewski <lukma@denx.de> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2020-01-14mmc: fsl_esdhc_imx: Handle the "broken-cd" propertyFabio Estevam
When no GPIO is used to read the card detect status the following error is seen: MMC: FSL_SDHC: 0, FSL_SDHC: 1 Loading Environment from MMC... MMC: no card present *** Warning - No block device, using default environment Fix it by handling the "broken-cd" property in the same way that drivers/mmc/sdhci.c does, which considers that the SD card is present when the "broken-cd" property is passed. Tested on a imx6ul-evk board. Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
2020-01-14net: zynq: Add a note about RX_BUF macroMichal Simek
Record note about reducing number of BDs. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14firmware: Remove probe which is causing extra bindAshok Reddy Soma
Remove probe function dm_scan_fdt_dev from zynqmp-firmware driver. It is just binding its subnode zynqmp-clk. As a result one extra node is showing up in dm tree. This is not required, it is anyway bound from it's own zynqmp-clk driver. Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14zynq: mtd: nand: Remove hardcoded base addressesAshok Reddy Soma
Remove hardcoded base addresses of smc controller and nand controller. Get those addresses from dt and replace wherever they are used. Remove smc and nand base address from header file too. Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14zynq: mtd: nand: Move zynq nand driver to driver modelAshok Reddy Soma
Move the zynq nand driver to driver model. Select DM_MTD if zynq nand controller (NAND_ZYNQ) is selected. Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14spi: Fix manual relocation calling more timesAshok Reddy Soma
When two instances of AXI QSPI with flash are added and tested simultaneously the spi driver operations are relocated twice. As a result code is accessing addresses outside of RAM when relocated second time which is causing a crash. Tested on Microblaze. Similar change was done in past by: commit f238b3f0fbc9 ("watchdog: dm: Support manual relocation for watchdogs") commit 2588f2ddfd60 ("dm: sf: Add support for all targets which requires MANUAL_RELOC") commit 1b4c2aa25bdf ("gpio: dm: Support manual relocation for gpio") Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14mtd: nand: Remove hardcoded base address of nandAshok Reddy Soma
Remove hardcoded base address of nand and replace it with the value taken from device tree. Remove base address from header file too. Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14mtd: nand: Move arasan nand driver to driver modelAshok Reddy Soma
Make changes to arasan nand driver to move it to driver model. Select DM_MTD if arasan nand driver is selected. Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-10virtio: fix typo devicdHeinrich Schuchardt
%s/devicd/device Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2020-01-10poweroff: add poweroff for mt6323 pmicFrank Wunderlich
this adds poweroff to bananapi r2 / mt7623 / mt6323 pmic Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
2020-01-10rtc: add support for DS3232 deviceHan Nandor
DS3232 is an i2c RTC with 236 bytes of battery-backed SRAM. Add an RTC driver for DS3232 device, which provides time and date support. Also read and write functions are provided, which can be used to access the SRAM memory. Signed-off-by: Nandor Han <nandor.han@vaisala.com>
2020-01-10bootcount: add a DM i2c eeprom backing store for bootcountRobert Beckett
This driver allows the use of i2c eeprom device or partition as backing store for boot counter values with DM enabled. Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
2020-01-10drivers: mcfmii: add dm supportAngelo Durgehello
Add specific dm code, but maintaining this driver as is, so more in the shape of a mii library. Can be moved to dm in a further step. Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
2020-01-10drivers: fsl_mcdmafec: conversion to dmAngelo Durgehello
Full conversion to dm for all boards, legacy code removed. Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
2020-01-10drivers: mcffec: conversion to dmAngelo Durgehello
Full conversion to dm for all boards, legacy code removed. Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
2020-01-10drivers: net: add mcf fec dm Kconfig supportAngelo Durgehello
Add ColdFire fec to Kconfig. Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
2020-01-09Merge branch 'next' of https://gitlab.denx.de/u-boot/custodians/u-boot-mpc83xxTom Rini
- A small PR with MC8309 fixes from Rasmus.
2020-01-09Merge tag 'dm-pull-8jan20' of git://git.denx.de/u-boot-dmTom Rini
dm: Increased separation of ofdata_to_platdata() and probe methods
2020-01-09Merge branch 'master' of git://git.denx.de/u-boot-usbTom Rini
- DFU updates
2020-01-08Merge tag 'efi-2020-04-rc1' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-efi Pull request for UEFI sub-system for efi-2020-04-rc1 This pull request provides: * support for FIT images for UEFI binaries * drivers for hardware random number generators * an implementation of the EFI_RNG_PROTOCOL * a sub-command for efidebug to display configuration tables
2020-01-08Merge tag 'u-boot-imx-20200108' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-imx --------------------------------------------------------------------- Add i.MX8MP SoC and EVK board Update README for i.MX8MN EVK and fix mmc env Add pca9450 driver -------------------------------------------------------------------- Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/634211885
2020-01-08Merge branch 'master' of git://git.denx.de/u-boot-socfpgaTom Rini
2020-01-08Merge tag 'u-boot-amlogic-20200108' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic - Khadas VIM3L based on Amlogic S905D3 support - Various fixups for amlogic boards - Unnecessary header includes drop into video/meson
generated by cgit (git 2.34.1) at 2025-01-01 00:00:19 +0000