summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2020-10-18More fixingDaniel Palmer
2020-10-01i2c: rcar_i2c: Fix i2c read/write errorsLad Prabhakar
commit 7c8f821e5dde ("i2c: rcar_i2c: Set the slave address from rcar_i2c_xfer") blindly called rcar_i2c_set_addr() with read argument always set to 1 during xfer which introduced read/write errors, whereas earlier rcar_i2c_read_common() called rcar_i2c_set_addr() with read set to 1 and rcar_i2c_write_common() called rcar_i2c_set_addr() with read set 0. Fixes: 7c8f821e5dde ("i2c: rcar_i2c: Set the slave address from rcar_i2c_xfer") Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com> Reviewed-by: Heiko Schocher <hs@denx.de>
2020-09-29video: typo NormllyHeinrich Schuchardt
%s/Normlly/Normally/ Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-09-29mtd: fix typos in drivers/mtd/Kconfig, drivers/mtd/renesas_rpc_hf.cHeinrich Schuchardt
Fix a typo %s/interract/interact/ Use Samsung's capitalization of their trademarks %s/onenand/OneNAND/ %s/Hyperflash/HyperFlash/ Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Stefan Roese <sr@denx.de> [trini: Add other Hyperflash cases as noted by Stefan] Signed-off-by: Tom Rini <trini@konsulko.com>
2020-09-28Merge tag 'u-boot-amlogic-20200928' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic - fix RNG driver probe & linux EFI KASLR boot on GXL, GXM, G12A, G12B & SM1 based boards
2020-09-28rng: meson: make core clock optionalNeil Armstrong
This fixes HWRNG support on Amlogic GXL, GXM, G12A, G12B & SM1 based boards dues to the lack of the core clock in the device tree. It was reported breaking EFI boot in the Linux EFI stub, because the EFI_RNG_PROTOCOL didn't check for the RNG device presence before installing itself. The Linux amlogic,meson-rng.yaml doesn't mandate the core clock, this the clock should be ignores if not present. Nevertheless, the clock should be present and this should be fixed on the Linux meson-gxl.dtsi & meson-g12-common.dtsi then synced with U-Boot. The change has been tested on a Khadas VIM3, which uses the common meson-g12-common.dtsi like the Odroid-C4 & Odroid-N2 in Scott's report, along with the RNG cmd. Cc: Heinrich Schuchardt <xypron.glpk@gmx.de> Reported-by: Scott K Logan <logans@cottsay.net> Fixes: bc40eb278b ("drivers/rng: add Amlogic hardware RNG driver") Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Tested-by: Scott K Logan <logans@cottsay.net> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2020-09-25Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriqTom Rini
- Bug fixes related to PCIe, pfe, xfi, gpio, reset, vid, env, and usb on layerscape products
2020-09-24pci: layerscape: Fixup PCIe EP mode DT nodes for LX2160A rev2Hou Zhiqiang
LX2160A rev2 uses different PCIe controller, so EP mode DT nodes also need to be fixed up. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24net: pfe_eth: Remove non-DM code check from pfe_spi_flash_initKuldeep Singh
CONFIG_DM_SPI_FLASH is only supported now with passing of driver conversion deadline from non-DM to DM model. Hence, it's safe to remove non-DM code check from pfe_spi_flash_init. Also use CONFIG_ENV_SPI_MODE and CONFIG_ENV_SPI_MAX_HZ instead of reading reading values from DT. Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24net: pfe_eth: Fix resoure leak in pfe_spi_flash_initKuldeep Singh
Fix Coverity issue: RESOURCE_LEAK. leaked_storage: Variable addr going out of scope leaks the storage it points to. Fixes: e0152dbed683 ("net: pfe_eth: Use spi_flash_read API to access flash memory") Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24driver: net: fm: add support for XFIMadalin Bucur
All the 10G ports that were working in XFI mode were described as using XGMII (as PHY_INTERFACE_MODE_XFI was not added at the time). Add the minimal changes required for the FMan code to support XFI. Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24ls1012a, pfe_eth: Update probe to avoid resource leakChaitanya Sakinam
PFE DDR addresses are now stored on to a stack varaiable rather dynamic allocation. Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24ls1012a, pfe_eth: correction in delay implementationChaitanya Sakinam
correction in delay implementation before we exit out of tx timeout. Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24drivers: net: phy: Use Aquantia driver for AQR113CMadalin Bucur
Add support for AQR113C PHY Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24drivers: net: ldpaa_eth: lx2160a: fix bug in checking if a DPMAC is enabledGrigore Popescu
The next DPMAC was always verified if it is enabled. In case of DPMAC@6, the DPMAC@7 is verified. As DPMAC@7 is disabled, DPMAC@6 will be considered disabled and not detected by uboot. Signed-off-by: Grigore Popescu <grigore.popescu@nxp.com> Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-24arm64: a37xx: pci: Disable link training when unloading driverPali Rohár
As required by PCI Express spec a delay for at least 100ms after de-asserting PERST# signal is needed before link training is enabled. Linux kernels prior to 5.8 version do not automatically disable link training before de-asserting PERST# signal, therefore this requirement is not fulfilled. Above requirement is needed for proper detection of some Compex PCIe WiFi cards. Otherwise Linux kernel cannot detect it. To allow using those PCIe cards with older Linux kernel versions booted by U-Boot compiled with U-Boot a37xx pci driver, disable link training in U-Boot when unloading this pci driver. Thanks to DM_FLAG_OS_PREPARE flag, U-Boot automatically unload this driver when booting Linux kernel. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
2020-09-24mtd: spi-nor-ids: add support for Macronix mx25u12835f flashVladimir Vid
Some of Marvell A3700 boards use mx25u12835f, specifically uDPU and ESPRESSObin v7. Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr> [a.heider: adapt commit message to mainline] Signed-off-by: Andre Heider <a.heider@gmail.com>
2020-09-23pci: layerscape: Fix spurious writes and panicMichael Walle
The fdt_fixup_pcie_ls() scans all PCI devices and assumes that all PCI root devices are layerscape PCIe controllers. Unfortunately, this is not true for the LS1028A. There is one additional static PCI root complex (this contains the networking devices) which has nothing to do with the layerscape PCIe controllers. On recent U-Boot versions this results in the following panic: "Synchronous Abort" handler, esr 0x96000044 elr: 000000009602fa04 lr : 000000009602f9f4 (reloc) elr: 00000000fbd73a04 lr : 00000000fbd739f4 x0 : 0080000002000101 x1 : 0000000000000000 x2 : 00000000fbde9000 x3 : 0000000000000001 x4 : 0000000000000000 x5 : 0000000000000030 x6 : 00000000fbdbd460 x7 : 00000000fbb3d3a0 x8 : 0000000000000002 x9 : 000000000000000c x10: 00000000ffffffe8 x11: 0000000000000006 x12: 000000000001869f x13: 0000000000000a2c x14: 00000000fbb3d2cc x15: 00000000ffffffff x16: 0000000000010000 x17: 0000000000000000 x18: 00000000fbb3fda0 x19: 0000000000000800 x20: 0000000000000000 x21: 00000001f0000000 x22: 0000000000000800 x23: 0000000000000009 x24: 00000000fbdc3c1b x25: 00000000fbdc28e5 x26: 00000000fbdcc008 x27: 00000000fbdc16e2 x28: 000000000f000000 x29: 00000000fbb3d3a0 Code: 394072a1 f94006a0 34000041 5ac00a94 (b8336814) Resetting CPU ... This bug already existed in former versions, but the spurious write was never trapped, because the destination address was a valid address (by pure luck). Make sure the PCI root is actually one of the expected PCIe layerscape controllers by matching its compatible string. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Tested-by: Heiko Thiery <heiko.thiery@gmail.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-09-23pinmux: pic32: add SDHCI pin configJohn Robertson
The GPIO pins used by the SDHCI controller need to be configured to allow the interface to work. Signed-off-by: John Robertson <john.robertson@simiatec.com>
2020-09-23mmc: pic32: Refresh PIC32 MMC driverJohn Robertson
The existing driver is not compatible with the Driver Model. This patch makes the necessary changes while also removing obsolescent calls/properties as follows: - fdtdec_* calls replaced with dev_read_* equivalents; - 'clock-freq-min-max' property replaced by querying the frequency of the source clock 'base_clk'; - The card detect erratum workaround is applied during probe rather than overriding get_cd. The card detect workaround (Microchip ref. DS80000736E, erratum #15) is not always needed and can be disabled using a vendor specific DT property. Signed-off-by: John Robertson <john.robertson@simiatec.com>
2020-09-22gpio/mpc83xx_spisel_boot.c: include log.hRasmus Villemoes
Fix build failure, it used to get this implicitly through common.h until f7ae49fc4f (common: Drop log.h from common header). Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Reviewed-by: Heiko Schocher <hs@denx.de>
2020-09-22spi: mpc8xxx_spi.c: fix cs activate/deactivateRasmus Villemoes
Somewhere between v2020.04 and v2020.07 the mpc8xxx_spi driver broke, I'm guessing due to this hunk @@ -559,6 +560,8 @@ int dm_gpio_set_dir_flags(struct gpio_desc *desc, ulong flags) if (ret) return ret; + /* combine the requested flags (for IN/OUT) and the descriptor flags */ + flags |= desc->flags; ret = _dm_gpio_set_dir_flags(desc, flags); from commit 695e5fd5469a ("gpio: update dir_flags management"). But the blame is mostly on the driver itself which seems rather confused: The chip select gpios are requested with GPIOD_ACTIVE_LOW, but then in each activate/deactivate, dm_gpio_set_dir_flags() is called with merely GPIOD_IS_OUT, and then the driver call set_value(0) for activate. That used to work, but with the above hunk, the ACTIVE_LOW setting from the request becomes persistent, so the gpio driver ends up being asked to set the value to 1 in mpc8xxx_spi_cs_activate(). So drop the dm_gpio_set_dir_flags() calls in the activate/deactivate functions, and use a value of 1 to mean "logically enabled". Ideally, I think we should also drop the GPIOD_ACTIVE_LOW from the request and make it up to the list of gpio cs in DT to indicate whether that CS is enabled when driven low (as is of course usually the case), but that requires changing arch/powerpc/dts/gdsys/gazerbeam-base.dtsi among others, and I don't have that hardware to test on. I have, however, tested our own (mpc8309-based) hardware with this change, and I have also tested that removing the GPIOD_ACTIVE_LOW from the request and updating our DT as - gpios = <&spisel 0 0>; + gpios = <&spisel 0 GPIO_ACTIVE_LOW>; still works. Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
2020-09-19Merge tag 'efi-2020-10-rc5-2' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-efi Pull request for UEFI sub-system for efi-2020-10-rc5 (2) The following bugs are fixed: * incorrect online help for setenv and env * description of function efi_mem_carve_out() * replace printf() by log_err() in stm32mp1_rng driver A unit test is provided to check that the boot hart id is provided in the RISC-V device-tree.
2020-09-18rng: stm32mp1: use log() instead of printf()Heinrich Schuchardt
The logging system provides flexible filtering and enhanced output. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Sughosh Ganu <sughosh.ganu@linaro.org>
2020-09-17mmc: fsl_esdhc_imx: check the clock stable status after config the clock rate.Haibo Chen
Currently, after config the clock rate, delay 10ms, this is quite a rough method. Check the clock stable status in the present status register is enough. Tested-by: Ji Luo <ji.luo@nxp.com> Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
2020-09-15mmc: xenon_sdhci: Add missing common host capabilitiesAndre Heider
Use mmc_of_parse() to set the common host properties. That includes "bus-width", so parsing it can be removed from the driver. But more importantly, "non-removable" is now respected, which fixes the usage of eMMC. Signed-off-by: Andre Heider <a.heider@gmail.com> Reviewed-by: Konstantin Porotchkin <kostap@marvell.com> Tested-by: Marek Behún <marek.behun@nic.cz>
2020-09-15mmc: msm_sdhci: Use mmc_of_parse for setting host_capsManivannan Sadhasivam
Since the introduction of 'get_cd' callback in sdhci core, dragonboard410c's MMC interface is broken. It turns out that 'get_cd' callback checks for the host_caps for validating the chip select. And since the msm_sdhci driver is not parsing the host_caps from DT, not all of the cababilities are parsed properly. This results in the MMC interfaces to be broken. Hence, fix this by adding a call to 'mmc_of_parse' during driver probe. Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Tested-by: Aníbal Limón <anibal.limon@linaro.org> Reviewed-By: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2020-09-11mtd: nand: Fix nand write error with bad block addresses above 32-bitT Karthik Reddy
Nand writes should skip the bad blocks with "nand write" command. In case of bad blocks with above 32-bit address, nand_block_isbad() returns false due to truncated bad block address. In below code segment, if (nand_block_isbad(mtd, offset & ~(mtd->erasesize - 1))) offset is 64-bit and mtd->erasesize is 32-bit, hence the truncation is happening. Cast 'mtd->erasesize' with loff_t to fix this issue. Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-09-10PCI: mediatek: Release the resource when PCIe enable port failChuanjia Liu
On the mt7623 platform, if one port enable fail and other port enable succeed. It will hang on when using pci enum because the resource was not released correctly. Signed-off-by: Chuanjia Liu <Chuanjia.Liu@mediatek.com> Tested-by: Frank Wunderlich <frank-w@public-files.de>
2020-09-08bcmgenet: Add support for rgmii-rxidJason Wessel
The commit 57805f2270c4 ("net: bcmgenet: Don't set ID_MODE_DIS when not using RGMII") needed to be extended for the case of using the rgmii-rxid. The latest version of the Rasbperry Pi4 dtb files for the 5.4 now specify the rgmii-rxid. Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Tested-by: Petr Tesarik <ptesarik@suse.com> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2020-09-08bcmgenet: fix DMA buffer managementJason Wessel
This commit fixes a serious issue occurring when several network commands are run on a raspberry pi 4 board: for instance a "dhcp" command and then one or several "tftp" commands. In this case, packet recv callbacks were called several times on the same packets, and send function was failing most of the time. note: if the boot procedure is made of a single network command, the issue is not visible. The issue is related to management of the packet ring buffers (producer / consumer) and DMA. Each time a packet is received, the ethernet device stores it in the buffer and increments an index called RDMA_PROD_INDEX. Each time the driver outputs a received packet, it increments another index called RDMA_CONS_INDEX. Between each pair of network commands, as part of the driver 'start' function, previous code tried to reset both RDMA_CONS_INDEX and RDMA_PROD_INDEX to 0. But RDMA_PROD_INDEX cannot be written from driver side, thus its value was actually not updated, and only RDMA_CONS_INDEX was reset to 0. This was resulting in a major synchronization issue between the driver and the device. Most visible behavior was that the driver seemed to receive again the packets from the previous commands (e.g. DHCP response packets "received" again when performing the first TFTP command). This fix consists in setting RDMA_CONS_INDEX to the same value as RDMA_PROD_INDEX, when resetting the driver. The same kind of fix was needed on the TX side, and a few variables had to be reset accordingly (c_index, tx_index, rx_index). The rx_index and tx_index have only 256 entries so the bottom 8 bits must be masked off. Originated-by: Etienne Dublé <etienne.duble@imag.fr> Signed-off-by: Jason Wessel <jason.wessel@windriver.com> Tested-by: Petr Tesarik <ptesarik@suse.com> Signed-off-by: Matthias Brugger <mbrugger@suse.com>
2020-09-04phy: marvell: a3700: add sata comphy on lane 2 with invert optionzachary
- This patch moves sata phy powerup from dedicate phy to compphy and adds invert option for sata powerup routine. Change-Id: I1b4e8753e2b2c14c6efa97bca2ffc7d2553d8a90 Signed-off-by: zachary <zhangzg@marvell.com> Signed-off-by: Ken Ma <make@marvell.com> Reviewed-on: http://vgitil04.il.marvell.com:8080/53601 Reviewed-by: Igal Liberman <igall@marvell.com> Tested-by: Igal Liberman <igall@marvell.com> [a.heider: adapt to mainline] Signed-off-by: Andre Heider <a.heider@gmail.com> Tested-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
2020-09-03Merge branch 'master' of git://git.denx.de/u-boot-usbTom Rini
- Mostly DFU fixes and r8152 fixes
2020-09-03Merge branch 'master' of git://git.denx.de/u-boot-shTom Rini
- SH serial bugfix
2020-09-01fastboot: getvar: fix partition-size return valueGary Bisson
The size returned by 'getvar partition-size' should be in bytes, not in blocks as fastboot uses that value to generate empty partition when running format [1]. Note that the function was already returning the proper size in bytes for NAND devices (see struct part_info details). [1] https://android.googlesource.com/platform/system/core/+/refs/heads/android10-release/fastboot/fastboot.cpp#1500 Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
2020-09-01fastboot: Fix fastboot reboot fail by changing functions orderyurii.pidhornyi
It was revealed that when the fastboot_tx_write_str function is called without the previously initialized fastboot_func->in_req->complete field, a copy of in_req will be sent to the I/O requests queue without an initialized field. Moving a piece of code with the initializing of the fastboot_func->in_req->complete field above transmit_tx allows to solve this problem. Fixes: 65c96757fe9 "usb: fastboot: Convert USB f_fastboot to shared fastboot" Signed-off-by: yurii.pidhornyi <yurii.pidhornyi@globallogic.com>
2020-09-01f_sdp: Change bInterval of interrupt endpoint to 3Sherry Sun
Since the USB HID limits the maximum bandwidth(3072) for interrupt endpoint transfers, when the bInterval set to 1, we can only support 3 boards to run sdp at the same time. In order to support more boards, change the bInterval of interrupt endpoint to 3, which will not affect the transmission speed. Reviewed-by: Ye Li <ye.li@nxp.com> Signed-off-by: Sherry Sun <sherry.sun@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-09-01f_sdp: Add EP1_OUT as default data receive pipe in sdpSherry Sun
EP0 has been used to transfer file data in sdp before, but the max packetsize of ep0 is 64 bytes. So in order to improve the file transfer speed, here add the EP1_OUT interrupt endpoint which max packetsize is set to 1024 byte. After testing, it turns out that using ep1out is twice as fast as using ep0 while receiving data in sdp. Signed-off-by: Sherry Sun <sherry.sun@nxp.com> Reviewed-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-09-01f_sdp: Support searching and loading FIT or container imagePeng Fan
Add support to f_sdp to search and load iMX8 container image or iMX8M FIT image by new UUU command SDPV. When using the SDPV, the uuu will continue to send out data after first level boot loader used by ROM. This means uuu won't skip to the offset of the second boot loader, and the padding data before second boot loader will be sent out. So we have to search the FIT header or container header in the buffer that SDP received. Also change to more common method to exit f_sdp handler not depending on SPL_FIT_FOUND flag because container loader won't set this. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-09-01f_sdp: Fix wrong usb request sizeYe Li
Because the buffer length of sdp usb request is 65, we have to allocate 65 bytes not 64 bytes. Otherwise there is potential buffer overflow. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2020-09-01f_sdp: Add high speed endpoint descriptorYe Li
Add HS endpoint descriptor for SDP. So that we can use high speed endpoint, and the SDP device can send packet with 512 byte size. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2020-09-01usb: max3420: add the gadget driverJassi Brar
MAX3420 implements FullSpeed USB Device over SPI. Another version MAX3421, also implements USB Host mode. This driver should be good for the device mode of max3421 as well. Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
2020-09-01fastboot: Add default fastboot_set_reboot_flag implementationRoman Kovalivskyi
Default implementation of fastboot_set_reboot_flag function that depends on "bcb" commands could be used in general case if there are no need to make any platform-specific implementation, otherwise it could be disabled via Kconfig option FASTBOOT_USE_BCB_SET_REBOOT_FLAG. Please note that FASTBOOT_USE_BCB_SET_REBOOT_FLAG is mutually exclusive with some platforms which already have their own implementation of this function. Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
2020-09-01fastboot: Add support for 'reboot fastboot' commandRoman Kovalivskyi
Android 10 adds support for dynamic partitions and in order to support this userspace fastboot must be used[1]. New tool fastbootd is included into recovery. Userspace fastboot works from recovery and is launched if: 1) - Dynamic partitioning is enabled 2) - Boot control block has 'boot-fastboot' value into command field The bootloader is expected to load and boot into the recovery image upon seeing boot-fastboot in the BCB command. Recovery then parses the BCB message and switches to fastbootd mode[2]. Please note that boot script is expected to handle 'boot-fastboot' command in BCB and load into recovery mode. Bootloader must support 'reboot fastboot' command which should reboot device into userspace fastboot to accomodate those changes[3]. Another command that bootloader must support[3] is 'reboot recovery'. This command should simply reboot device into recovery mode. [1] - https://source.android.com/devices/bootloader/fastbootd [2] - https://source.android.com/devices/bootloader/fastbootd#unified_fastboot_and_recovery [3] - https://source.android.com/devices/bootloader/fastbootd#modifications_to_the_bootloader Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com> Signed-off-by: Roman Stratiienko <r.stratiienko@gmail.com> Change-Id: I9d2bdc9a6f6f31ea98572fe155e1cc8341e9af76
2020-09-01fastboot: Extend fastboot_set_reboot_flag with reboot reasonRoman Kovalivskyi
Extend fastboot_set_reboot_flag arguments with reboot reason so that it could handle different reboot cases in future. Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
2020-09-01dfu: fix dfu tftp on sandboxHeinrich Schuchardt
The environment variable loadaddr is in the virtual address space of the sandbox. To get the actual memory address where the FIT image has been loaded we have to convert this address according to the memory mapping of the sandbox. Equally the addresses in the *.its file have to be converted when used in the dfu_ram driver. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-09-01dfu: DFU_MTD depends on CMD_MTDPARTSHeinrich Schuchardt
Function mtdparts_init() is needed for the DFU MTD driver. Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2020-09-01fastboot: Support defining raw partitions without a partition tableFilip Brozovic
Add support for defining raw fastboot partitions in eMMC by specifying the offset and size in an environment variable. Optionally, the eMMC hardware partition number may also be specified. This makes it possible to e.g. update only part of the eMMC boot partition, instead of having to write the entire partition. Signed-off-by: Filip Brozovic <fbrozovic@gmail.com>
2020-09-01usb: ci_udc: Add function to remove usb deviceYe Li
When unregister gadget driver in ci_udc, the usb device is not removed or stop. This causes next "usb start" fails to work. Add a new interface "usb_remove_ehci_gadget" in usb-uclass to remove the usb device for DM driver. Using "usb_lowlevel_stop" for non-DM driver. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-09-01usb: gadget: Fix controller index in UMSYe Li
The usb mass storage (f_mass_storage.c) uses fixed usb index 0, this causes problem while CDNS3 USB controller index is 1. Modify the API of fsg to pass the controller index. Reviewed-by: Jun Li <jun.li@nxp.com> Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
generated by cgit (git 2.34.1) at 2024-12-22 23:12:52 +0000