| Age | Commit message (Collapse) | Author |
|---|
|
|
|
At present IDE support is controlled by CONFIG_CMD_IDE. Add a separate
CONFIG_IDE option so that IDE support can be enabled without requiring
the 'ide' command.
Update existing users and move the ide driver into drivers/block since
it should not be in common/.
Signed-off-by: Simon Glass <sjg@chromium.org>
|
|
This converts the following to Kconfig:
CONFIG_CMD_HASH
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Rework slightly, enable on some boards again]
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
This is only used by one board and always set to 0x51. Drop this option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
This subsystem is quite old. It has been replaced with a driver-model
version (UCLASS_THERMAL). Boards are free to convert to that if required,
but here is a removal patch that could be applied in the meantime.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
This subsystem has not been converted to driver model, there is only one
driver and only one board that uses it. Drop it and its CONFIG option.
Also drop the rtc4543 RTC driver since it uses TWS.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
This option is only defined to a non-default value by canyonlands, which
needs conversion to driver model (where the I2C address would be defined
by the device tree).
Drop this option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
This converts the following to Kconfig:
CONFIG_DS4510
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
This option enables a command in the driver. But the functions defined by
the driver are not called anywhere else in U-Boot. So it does not seem
useful to have this driver without its commands.
Drop this option, move the header file out of the common include/
directory and make all the function static.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
This option is only used in one driver and is not enabled by any board. It
does not seem worth having the ability to remove this part of the support.
Drop the option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
This option is only used in one driver and is not enabled by any board. It
does not seem worth having the ability to remove this part of the support.
Drop the option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
This option is only used in one driver and two boards. It does not seem
worth having the ability to remove this part of the support.
Drop the option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
Commit 94e3c8c4fd7b ("crypto/fsl - Add progressive hashing support
using hardware acceleration.") created entries for CONFIG_SHA1,
CONFIG_SHA256, CONFIG_SHA_HW_ACCEL, and CONFIG_SHA_PROG_HW_ACCEL.
However, no defconfig has migrated to it. Complete the move by first
adding additional logic to various Kconfig files to select this when
required and then use the moveconfig tool. In many cases we can select
these because they are required to implement other drivers. We also
correct how we include the various hashing algorithms in SPL.
This commit was generated as follows (after Kconfig additions):
[1] tools/moveconfig.py -y SHA1 SHA256 SHA_HW_ACCEL
[2] tools/moveconfig.py -y SHA_PROG_HW_ACCEL
Note:
We cannot move SHA_HW_ACCEL and SHA_PROG_HW_ACCEL simultaneously
because there is dependency between them.
Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: Naveen Burmi <NaveenBurmi@freescale.com>
Cc: Po Liu <po.liu@freescale.com>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: Priyanka Jain <Priyanka.Jain@freescale.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Chander Kashyap <k.chander@samsung.com>
Cc: Steve Rae <steve.rae@raedomain.com>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Feng Li <feng.li_2@nxp.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Sumit Garg <sumit.garg@nxp.com>
Cc: Mingkai Hu <Mingkai.Hu@freescale.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Add a USB controller driver for the EHCI block in R8A7795/R8A7796 SoC.
This is a stopgap measure until we have proper DT support, clock and
reset framework in place, at which point we can switch to ehci-generic.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Support Andestech AE3xx platform: serial, timer device tree flow.
Signed-off-by: rick <rick@andestech.com>
|
|
Support AG101P timer device tree flow.
Signed-off-by: rick <rick@andestech.com>
|
|
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Add driver for the Renesas Ethernet AVB block found in RCar H3/M3.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Based on work of:
Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Takeshi Kihara <takeshi.kihara.df@renesas.com>
Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
|
|
This patch fixes to read the GPIO status after confirming the
INOUT setting.
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Tom Rini <trini@konsulko.com>
|
|
The mcs7830_recv() (non-DM) function discards good packets and tries to
process "bad" packets due to incorrect test condition.
Fix the condition and return the proper value as described in function
doc.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
|
|
|
|
Add DM support for i2c functions.
Signed-off-by: Liam Beguin <lbeguin@tycoint.com>
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
Each time set_state is called, a new piece memory will
be allocated for pin_data, but not freed, this will
incur memory leak.
When error, the devm API could not free memory automatically.
So need call devm_kfree when error.
Issue reported by Coverity
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Agner <stefan.agner@toradex.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Make oe-pins optional because some boards have fixed it to enable.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add the Kconfig entry for SOFT_SPI which uses gpio to simulate the
SPI signals. We use it for accessing 74x164 on some i.MX boards.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Fix calculation. do_div can not handle negative values.
Use div_s64_rem to handle the calculation.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
>From IC guys:
"
After a thorough accuracy study of the Temp sense circuit,
we found that with our current equation, an average part can
read 7 degrees lower than a known forced temperature.
We also found out that the standard variance was around 2C;
which is the tightest distribution that we could create.
We need to change the temp sense equation to center the average
part around the target temperature.
"
New equation:
Tmeas = (Nmeas - n1) / slope + t1 + offset
n1= fused room count
t1= 25
offset=3.580661
slope= 0.4148468 – 0.0015423*n1
According the new equation, update the thermal driver.
c1 and c2 changed to u64 type and update comments.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
|
|
Specify the registered eth index by dev_id.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
|
|
Avoid transfer parameter dev_id value with "-1" to .fec_get_hwaddr(),
it should transfer fec->dev_id to get mac address from fuse.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
The MIB RAM and FIFO receive start register does not exist on
i.MX6ULL. Accessing these register will cause enet not work well or
cause system report fault.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
|
|
Add a device-tree property use-lvl-write-cache that will cause
writes to lvl to be cached instead of read from lvl before each
write. This is required on some platforms that have the register
implemented as dual read/write (such as Baytrail).
Prior to this fix the blue USB port on the Minnowboard Max was
unusable since USB_HOST_EN0 was set high then immediately set
low when USB_HOST_EN1 was written.
This also resolves the 'gpio clear | set' command warning like:
"Warning: value of pin is still 0"
Signed-off-by: George McCollister <george.mccollister@gmail.com>
<rebased on latest origin/master, fixed all baytrail boards>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This patch adds a remove function to the Intel ICH SPI driver, that will
be called upon U-Boot exit, directly before the OS (Linux) is started.
This function takes care of configuring the BIOS registers in the SPI
controller (similar to what a "standard" BIOS or coreboot does), so that
the Linux MTD device driver is able to correctly read/write to the SPI
NOR chip. Without this, the chip is not detected at all.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Jagan Teki <jteki@openedev.com>
|
|
This new flag can be added to DM device drivers, which need to do some
final configuration before U-Boot exits and the OS (e.g. Linux) is
started. The remove functions of those drivers will get called at
this stage to do these last-stage configuration steps.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
|
|
On my x86 platform I've noticed, that calling dm_uninit() or the new
function dm_remove_devices_flags() does not remove the desired device at
all. Debugging showed, that the serial uclass returns -EPERM in
serial_pre_remove(). This patch sets the force parameter when calling
stdio_deregister_dev() resulting in a removal of the device.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Convert the pci_mmc driver over to driver model and migrate all x86 boards
that use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Introduce a new CONFIG_S3_VGA_ROM_RUN option so that U-Boot can
bypass executing VGA roms in S3.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Stefan Roese <sr@denx.de>
|
|
- Add #undef CONFIG_DM_MMC_OPS to omap3_logic in the SPL build case, to
match other TI platforms in the same situation.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
|
|
To fix the timeout of sending the write command, enable the quirk
SDHCI_QUIRK_WAIT_SEND_CMD.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Newer SoCs use same TV encoder unit. Split it out so it can be reused
with new DM video driver.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Due to a typo, the 24 bit-per-pixel configuration ends in 24BMP
instead of 24BPP. This change renames it throughout the source tree
for consistency and to make moving these options into Kconfig easier
and less error-prone.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
|
|
Instead of having drivers/video/rockchip/Kconfig point outside of its
hierarchy for dw_hdmi.o, we should use a configuration-option to
include the Designware HDMI support.
This change introduces a new config option (not to be selected via
menuconfig, but to be selected from a dependent video driver's
configuration option) that enables dw_hdmi.o and selects it whenever
the HDMI support for Rockchip SoCs is selected.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Some DVI monitors don't work in HDMI mode. Set it only if edid data
explicitly states that it is supported.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
|
|
Now that CMD_POWEROFF can turn off the twl4030, let's imply that
just incase someone wants to disable it.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Follow the exiting logic for the i.MX options when migrating this
option.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
The following options are migrated over fully now:
- USB_EHCI_ATMEL
- USB_EHCI_MARVELL
- USB_EHCI_MX6
- USB_EHCI_MX7
- USB_EHCI_MSM
- USB_EHCI_ZYNQ
- USB_EHCI_GENERIC
This also requires fixing the depends on USB_EHCI_MARVELL as it's used
by Orion5X and Kirkwood as well.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
Migrate the rest of the users of CONFIG_USB_EHCI_HCD over to Kconfig.
For a few SoCs, imply or default y this if USB is enabled. In some
cases we had not already migrated to CONFIG_USB so do that as well.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
In order to be able to migrate the various SoC EHCI CONFIG options we
first need to finish the switch from CONFIG_USB_EHCI to
CONFIG_USB_EHCI_HCD.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
|
|
Move this entry to Kconfig. As it is a hardware watchdog, select
HW_WATCHDOG. While we could default to enabling this for all platforms,
it is currently only enabled by default on AM33XX, so keep that logic
today.
Cc: Roger Meier <r.meier@siemens.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
