summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2014-10-31twl4030: VMMC2 3.2V enable on MMC initPaul Kocialkowski
This enables the VMMC2 LDO, which powers the MMC2 device. When the device starts from MMC2, this has already been enabled by the BootROM, but when starting from peripheral boot (USB, UART), it is not the case. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-10-29i2c: designware: Convert driver to multibus/multiadapter frameworkStefan Roese
In preparation for the SoCFPGA support of the designware I2C driver, convert this driver to the common CONFIG_SYS_I2C framework. This patch converts all users of this driver, this is: - ST spearxxx boards - AXS101 (ARC700 platform) I couldn't test this patch on those boards. Only compile tested for all spear boards. And tested on SoCFPGA. Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Marek Vasut <marex@denx.de> Acked-by: Alexey Brodkin <abrodkin@synopsys.com> Tested-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Heiko Schocher <hs@denx.de> Cc: Vipin Kumar <vk.vipin@gmail.com> Cc: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-29i2c: mxs: Add support for I2C 1 on i.MX28Marek Vasut
Add support for I2C bus 1 on the i.MX28. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Heiko Schocher <hs@denx.de>
2014-10-29i2c: mxs: Pass the i2c_adapter aroundMarek Vasut
This patch permeates the struct i2c_adapter throughout the driver, so that it can be used to determine which adapter should be used. Note that the driver still supports only one adapter. Note that the patch does shuffle mxs_i2c_set_bus_speed() to the top of the driver, but the function remains unchanged. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Heiko Schocher <hs@denx.de>
2014-10-29i2c: mxs: Add basic support for i2c frameworkMarek Vasut
This patch just converts the function prototypes used throughout this driver to match those of the i2c framework. There is so far no functional change. This patch does not do the deeper integration of the framework bits. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Heiko Schocher <hs@denx.de>
2014-10-29i2c: mxs: Consolidate hard-coded bus addressMarek Vasut
This patch prepares the MXS I2C driver for the conversion to the new I2C driver framework by pulling out the hard-coded I2C0 address from all the places. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Heiko Schocher <hs@denx.de>
2014-10-28dwc_ahsata: use bitwise operator in sata_port_statusNikita Kiryanov
The logic of the return statement in sata_port_status() calls for a bitwise 'AND' operator, not logical 'AND'. Fix the typo. Reported-by: Jeroen Hofstee <jeroen@myspectrum.nl> Cc: Jeroen Hofstee <jeroen@myspectrum.nl> Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
2014-10-28Merge git://git.denx.de/u-boot-dmTom Rini
2014-10-28e1000: add i211 and unprogrammed i210/i211 supportMarcel Ziswiler
This patch adds support for i211 as well as unprogrammed aka tools only i210/i211 chip support. Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
2014-10-27mmc: s5p: set SD detection pin as inputPrzemyslaw Marczak
The SD Card slot detection pin should be configured as input. Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com> Acked-by: Simon Glass <sjg@chromium.org>
2014-10-27e1000: fix sw fw sync on igb i210/i211Marcel Ziswiler
I finally had a look at the datasheet and spotted an additional register address difference between regular E1000 and i210/i211 chips. This patch fixes this and now successfully works on programmed i210/i211 as well as unprogrammed i211. Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
2014-10-27net/e1000: Fix EEPROM access errorYork Sun
Commit 951860634fdb557bbb58e0f99215391bc0c29779 may have changed the logic unintentially from "if (!(swfw_sync & (fwmask | swmask)))" to "if ((swfw_sync & swmask) && !(swfw_sync & fwmask))". This change breaks some e1000 NIC with a message "ERROR: Unable to read EEPROM!". Signed-off-by: York Sun <yorksun@freescale.com> CC: Marek Vasut <marex@denx.de> CC: Tim Harvey <tharvey@gateworks.com> Acked-by: Marcel Ziswiler <marcel@ziswiler.com>
2014-10-27Merge branch 'master' of git://git.denx.de/u-boot-mpc5xxxTom Rini
2014-10-27PowerPC: drop some 74xx_7xx boards and related codeWolfgang Denk
The file board/Marvell/include/mv_gen_reg.h is incompatible with the GPL (see for example the "MARVELL RESERVES THE RIGHT AT ITS SOLE DISCRETION TO REQUEST THAT THIS CODE BE IMMEDIATELY RETURNED TO MARVELL" clause). As this cannot be fixed, we remove the file and all code that depends on it. Fortunately this only affects some very old boards that have long reached EOL: CPCI750 DB64360 DB64460 p3m750 p3m7448 Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com> Cc: Stefan Roese <sr@denx.de> Cc: Roger Meier <r.meier@siemens.com>
2014-10-27Merge branch 'master' of git://git.denx.de/u-boot-imxTom Rini
2014-10-27Merge branch 'master' of git://git.denx.de/u-boot-tiTom Rini
2014-10-26Merge http://git.denx.de/u-boot-sunxiTom Rini
2014-10-26Merge branch 'master' of git://git.denx.de/u-boot-usbTom Rini
2014-10-26Merge git://git.denx.de/u-boot-dmTom Rini
Fix a trivial conflict over adding <dm.h> Conflicts: arch/arm/cpu/armv7/omap3/board.c Signed-off-by: Tom Rini <trini@ti.com>
2014-10-25i2c: designware: add an implement i2c protosJeroen Hofstee
Include the i2c header and change the non confirming functions to do so. Cc: Heiko Schocher <hs@denx.de> Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl> Acked-by: Heiko Schocher <hs@denx.de> [trini: Fix i2c_get_bus_num prototype] Signed-off-by: Tom Rini <trini@ti.com>
2014-10-25net: davince: add missing includeJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25mmc: bcm2835_sdhci: add missing includeJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25video: ipu: prevent warnings with W=1Jeroen Hofstee
- make local functions static - remove unused is_interlaced function Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25tegra: make local functions staticJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25serial: make local functions staticJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25sdhci: make local functions staticJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25omap_gpmc: fix warnigs with W=1Jeroen Hofstee
- make omap_spl_dev_ready static - make omap_reverse_list static, move to under CONFIG_NAND_OMAP_ELM Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl> Signed-off-by: Tom Rini <trini@ti.com>
2014-10-25net: fec_mxc: make local functions staticJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25gpio: make local functions staticJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25ehci-hcd.c: make local functions staticJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25video: use __weakJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25usb: use __weakJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25pci: use __weakJeroen Hofstee
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25net: phy: fix warnings with W=1Jeroen Hofstee
get_phy_id is marked weak but has no protype nor a strong version, just make it static. Use __weak for board_phy_config. Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25cti_flash.c: use __weak when requested for flash_(read|write){8,16,32,64}Jeroen Hofstee
For various reasons (design, errata) boards may need to implement their own versions of these accessors. So in the case of CONFIG_CFI_FLASH_USE_WEAK_ACCESSOR mark the functions as weak. In the normal case mark them as static to allow for better optimization. Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl> [trini: Reword commit message] Signed-off-by: Tom Rini <trini@ti.com>
2014-10-24mmc: sunxi: Add support for sun8i (A23)Chen-Yu Tsai
The Allwinner A23 SoC has reset controls like the A31 (sun6i). The FIFO address is also the same as sun6i. Re-use code added for sun6i. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24sunxi: When we've both mmc0 and mmc2, detect from which one we're bootingHans de Goede
sunxi SOCs can boot from both mmc0 and mmc2, detect from which one we're booting, and make that one "mmc dev 0" so that a single u-boot binary can be used for both the onboard eMMC and for external sdcards. When we're booting from mmc2, we make it dev 0 because that is where the SPL will load the tertiary payload (the actual u-boot binary in our case) from, see: common/spl/spl_mmc.c, which has dev 0 hardcoded everywhere. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24sunxi: Add mmc card-detect functionalityHans de Goede
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24ARM: sunxi-mmc: Add mmc support for sun6i / A31Hans de Goede
The mmc hardware on sun6i has an extra reset control that needs to be de-asserted prior to usage. Also the FIFO address is different. Signed-off-by: Hans de Goede <hdegoede@redhat.com> [wens@csie.org: use setbits_le32 for reset control, drop obsolete changes, rewrite different FIFO address handling, add commit message] Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Ian Campbell <ijc@hellion.org.uk>
2014-10-24mmc: sunxi: add SDHC support for sun6i/sun7i/sun8iWills Wang
Allwinner A20/A23/A31's SD/MMC host support SDHC High Capacity feature. Signed-off-by: Wills Wang <wills.wang.open@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2014-10-23serial: remove uniphier_serial_initialize() callMasahiro Yamada
The UniPhier serial driver has been converted to driver model. Let's remove uniphier_serial_initialize() call from the old serial driver framework. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
2014-10-23serial: uniphier: move CONFIG_UNIPHIER_SERIAL to KconfigMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
2014-10-23dm: serial: use Driver Model for UniPhier serial driverMasahiro Yamada
This commit converts UniPhier on-chip serial driver to driver model. Since UniPhier SoCs do not have Device Tree support, some board files should be added under arch/arm/cpu/armv7/uniphier/ph1-*/ directories. (Device Tree support for UniPhier platform is still under way.) Now the base address and master clock frequency are passed from platform data, so CONFIG_SYS_UNIPHIER_SERIAL_BASE* and CONFIG_SYS_UNIPHIER_UART_CLK should be removed. Tested on UniPhier PH1-LD4 ref board. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
2014-10-23dm: add entries to KconfigMasahiro Yamada
Create entries of CONFIG_DM, CONFIG_DM_SERIAL, CONFIG_DM_GPIO and CONFIG_DM_SPI. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
2014-10-23dm: serial: consolidate common code moreMasahiro Yamada
Commit b8893327e9d2 (dm: serial: Put common code into separate functions) consolidated getc() and putc(). This commit does more puts() and tsts(). Also rename locally used functions to _serial_*() for clarification because we have similar functions names here are there in this file. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
2014-10-23dm: serial: remove unnecessary castingMasahiro Yamada
The type (void *) can be directly passed to a function that takes a specific pointer type. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
2014-10-23dm: serial: fix console putcMasahiro Yamada
Commit b8893327e9d2 (dm: serial: Put common code into separate functions) consolidated getc() correctly, but introduced another bug to putc(); serial_stub_putc() passes sdev->priv to serial_putc_dev(), but serial_putc_dev() uses cur_dev instead of the given argument. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
2014-10-23serial: add static directive to local functionsMasahiro Yamada
The functions _serial_putc, _serial_putc_raw, _serial_puts, _serial_getc, _serial_tstc, _serial_setbrg are defined and used locally in each of serial_ns16550.c and serial_s3c24x0.c. Add static directive to them and remove declarations from include/common.h. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Simon Glass <sjg@chromium.org>
2014-10-23dm: move platform data headers to include/dm/platform_dataMasahiro Yamada
The platform_data definitions are generally referenced from both drivers and board files. That is why header files defining platform_data sturectures are placed in "include" directory, but our top level "include" directory is already too cluttered. Let's collect platform_data definitions under the directory "include/dm/platform_data" like Linux gathers ones around under "include/linux/platform_data". This commit moves two header files: include/serial_mxc.h -> include/dm/platform_data/serial_mxc.h include/serial_pl01x.h -> include/dm/platform_data/serial_pl01x.h Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-10-23dm: x86: Convert coreboot serial to use driver modelSimon Glass
This makes use of the existing device tree node to use driver model for the serial console. Signed-off-by: Simon Glass <sjg@chromium.org>
generated by cgit (git 2.34.1) at 2024-12-29 19:23:00 +0000