summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2011-10-10NAND: davinci: choose correct 1-bit h/w ECC regLaurence Withers
In nand_davinci_readecc(), select the correct NANDF<n>ECC register based on CONFIG_SYS_NAND_CS rather than hardcoding the choice of NANDF1ECC. This allows 1-bit hardware ECC to work with chip select other than CS2. Note this now matches the usage in nand_davinci_enable_hwecc(), which already had the correct handling, and allows refactoring to a single function encapsulating the register read. Without this fix, writing NAND pages to a chip not wired to CS2 would result in in the ECC calculation always returning FFFFFF for each 512-byte segment, and reading back a correctly written page (one with ECC intact) would always fail. With this fix, the ECC is written and verified correctly. Signed-off-by: Laurence Withers <lwithers@guralp.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
2011-10-09drivers/usb/host/ohci-hcd.c: fix warning: variable ... set but not usedWolfgang Denk
Fix: ohci-hcd.c: In function 'dl_transfer_length': ohci-hcd.c:968:8: warning: variable 'tdINFO' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Remy Bohmer <linux@bohmer.net> Acked-by: Remy Bohmer <linux@bohmer.net>
2011-10-09drivers/net/smc91111.c: fix warning: variable ... set but not usedWolfgang Denk
Fix: smc91111.c: In function 'smc_phy_configure': smc91111.c:1194:6: warning: variable 'failed' set but not used [-Wunused-but-set-variable] smc91111.c:1190:7: warning: variable 'phyaddr' set but not used [-Wunused-but-set-variable] Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-10-09CFI: fix warning: variable ... set but not usedWolfgang Denk
Fix: cfi_mtd.c: In function 'cfi_mtd_init': cfi_mtd.c:226:19: warning: variable 'mtd_list' set but not used [-Wunused-but-set-variable] cfi_mtd.c: In function 'cfi_mtd_init': cfi_mtd.c:225:6: warning: unused variable 'devices_found' cfi_mtd.c: In function 'cfi_mtd_init': cfi_mtd.c:226:19: warning: variable 'mtd_list' set but not used [-Wunused-but-set-variable] [-Wunused-variable] Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Stefan Roese <sr@denx.de> Acked-by: Stefan Roese <sr@denx.de>
2011-10-09netconsole: support packets longer than 512 bytesMichael Walle
Esp. while printing the environment the output is usually longer than 512 bytes. Instead of cutting the message, send multiple 512 bytes packets. Signed-off-by: Michael Walle <michael@walle.cc> Acked-by: Mike Frysinger <vapier@gentoo.org>
2011-10-09serial: uartlite: Support for SERIAL_MULTIMichal Simek
Add support for SERIAL MULTI for uartlite. Signed-off-by: Michal Simek <monstr@monstr.eu>
2011-10-05net: drop !NET_MULTI codeMike Frysinger
This is long over due. All but two net drivers have been converted, but those have now been dropped. The only thing left to do is actually delete all references to NET_MULTI and code that is compiled when that is not defined. So here we scrub the core code. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-05net: drop !NET_MULTI ns7520 driverMike Frysinger
This driver was never converted to NET_MULTI, and no board uses it. So punt it and be done. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-05net: drop !NET_MULTI bcm570x/tigon3 driversMike Frysinger
These drivers have never been converted to NET_MULTI, and they are only used by one board (BMW). So drop the drivers until someone feels like rewriting them for NET_MULTI support. Rather than punting the BMW board completely, just disable net support in its board config. Seems to build fine without it. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-05PPC: Cleanup tqm8xx_pcmcia.cMarek Vasut
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Tested-by: Wolfgang Denk <wd@denx.de> Acked-by: Wolfgang Denk <wd@denx.de>
2011-10-04Merge branch 'master' of git://git.denx.de/u-boot-nand-flashWolfgang Denk
* 'master' of git://git.denx.de/u-boot-nand-flash: PPC: Fix socrates NAND problem PPC: Fix fsl_upm.c by renaming nand handling functions NAND: Make page, erase, oob size available via cmd_nand mtd: eLBC NAND: remove elbc_fcm_ctrl->oob_poi NAND: Add -y option to nand scrub command NAND: Add nand read.raw and write.raw commands NAND: Really ignore bad blocks when scrubbing spl, nand: add 4bit HW ecc oob first nand_read_page function mxc_nand: fix a problem writing more than 32MB mxc_nand: fixed some typos (cosmetic) nand: increase chip_delay in mv kirkwood nand driver
2011-10-04Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk
* 'master' of git://git.denx.de/u-boot-mpc85xx: powerpc/p3060: Add SoC related support for P3060 platform powerpc/85xx: Add support for setting up RAID engine liodns on P5020 powerpc/85xx: Refactor some defines out of corenet_ds.h fm-eth: Add ability for board code to disable a port powerpc/mpc8548: Add workaround for erratum NMG_LBC103 powerpc/mpc8548: Add workaround for erratum NMG_DDR120 powerpc/mpc85xxcds: Fix PCI speed powerpc/mpc8548cds: Fix booting message powerpc/p4080: Add support for secure boot flow powerpc/85xx: Add Secure Boot support on P1010RDB for NOR, NAND & SPIFLASH powerpc/85xx: Add PBL & SECUREBOOT support on P3041/P5020DS boards powerpc/p2041rdb: remove watch dog related codes powerpc/p2041rdb: updated description of cpld command powerpc/p2041rdb: add more ddr frequencies support powerpc/p2041rdb: set sysclk according to status of physical switch SW1 powerpc/p2041rdb: update cpld reset command according to CPLD 2.0 powerpc/mpc8349emds: Migrate from spd_sdram to unified DDR driver powerpc/mpc83xx: Migrate from spd_sdram to unified DDR driver powerpc/mpc8xxx: Add DDR2 to unified DDR driver powerpc/mpc8xxx: Fix picos_to_mclk() and get_memory_clk_period_ps() powerpc/mpc8xxx: Add SPD EEPROM address for single controller 2 slots powerpc/mpc8xxx: Fix DDR code for empty first DIMM slot and enable DQS_en powerpc/85xx: Refactor P2041RDB to use common p_corenet files powerpc/85xx: refactor common P-Series CoreNet files for FSL boards powerpc/85xx: Enable CMD_REGINFO on corenet boards powerpc/85xx: p2041rdb - Remove unused 'execute' perm in TLB entries powerpc/85xx: Fix USB protocol definitions for P1020RDB powerpc/corenet_ds: Use separated speed tables for UDIMM and RDIMM powerpc/mpc8xxx: Move DDR RCW overriding to common code powerpc/mpc8xxx: Extend CWL table powerpc/85xx: Cleanup how SVR_MAJ() is defined on MPC8536 powerpc/85xx: Cleanup extern in corenet_ds board code powerpc/p2041rdb: Add ethernet support on P2041RDB board powerpc/85xx: Add networking support to P1023RDS powerpc/hydra: Add ethernet support on P5020/P3041 DS boards powerpc/85xx: Add FMan ethernet support to P4080DS powerpc/85xx: Add support for FMan ethernet in Independent mode powerpc/mpc8548cds: Cleanup mpc8548cds.c powerpc/mp: add support for discontiguous cores powerpc/85xx: corenet_ds - Remove unused 'execute' perm in TLB entries fdt: Add new fdt_create_phandle helper fdt: Rename fdt_create_phandle to fdt_set_phandle powerpc/85xx: Fix compile warnings/errors if CONFIG_SYS_DPAA_FMAN isn't set fsl_ifc: Add the workaround for erratum IFC A-003399(enabled on P1010) powerpc/P1010: Add workaround for erratum P1010-A003549 (related to IFC) fsl_ifc: Add the workaround for erratum IFC-A002769 (enable on P1010) powerpc/85xx: Expanding the window of CCSRBAR in AS=1 from 4k to 1M powerpc/85xx: Add NAND/NAND_SPL support to P1010RDB nand: Freescale Integrated Flash Controller NAND support powerpc/85xx: Add basic support for P1010RDB powerpc/85xx: Add support for new P102x/P2020 RDB style boards powerpc/85xx: relocate CCSR before creating the initial RAM area powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macros powerpc/85xx: Enable internal USB UTMI PHY on p204x/p3041/p50x0 powerpc/85xx: Add ULPI and UTMI USB Phy support for P1010/P1014
2011-10-04Merge branch 'master' of git://git.denx.de/u-boot-i2cWolfgang Denk
* 'master' of git://git.denx.de/u-boot-i2c: I2C: mv_i2c: fix multi-bus init issue I2C: mv_i2c: fix build issue when enable debug option
2011-10-03PPC: Fix fsl_upm.c by renaming nand handling functionsMarek Vasut
This avoids colision with nand subsystem's functions. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
2011-10-03mtd: eLBC NAND: remove elbc_fcm_ctrl->oob_poimhench
The eLBC NAND driver currently follows up each program/write operation with a read-back of the page, in order to [ostensibly] fill in ECC data for the caller. However, the page address used for this read is always -1, so the read will never work correctly. Remove this useless (and potentially problematic) block of code. v2: fix broken mailer Signed-off-by: mhench <mhench@elutions.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
2011-10-03NAND: Really ignore bad blocks when scrubbingMarek Vasut
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Scott Wood <scottwood@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de> [scottwood@freescale.com: use chip instead of redundant priv_nand] Signed-off-by: Scott Wood <scottwood@freescale.com>
2011-10-03mxc_nand: fix a problem writing more than 32MBHelmut Raiger
When writing 0x4000 to the unlockend_blkaddr register, large writes to a 2k page NAND sometimes fail. The current kernel driver writes 0xFFFF to this register for V2 of the nand controller. However on an i.MX31 this also fixes writes larger than 32MB. The datasheet is very unspecific, but (0x4000=16384)*2000 roughly fits the limits we're encountering with NAND writes. This problem might be NAND chip specific. Signed-off-by: Helmut Raiger <helmut.raiger@hale.at> Signed-off-by: Scott Wood <scottwood@freescale.com>
2011-10-03mxc_nand: fixed some typos (cosmetic)Helmut Raiger
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at> Signed-off-by: Scott Wood <scottwood@freescale.com>
2011-10-03nand: increase chip_delay in mv kirkwood nand driverStefan Bigler
The new SAMSUNG NAND Flash K9F1G08U0D require a bigger chip_delay. The Data Transfer from Cell to Register is >= 35us. Other Vendors and older chips normally use >= 25us. To have enough margin 40us is selected. Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com> Signed-off-by: Holger Brunck <holger.brunck@keymile.com> cc: Prafulla Wadaskar <prafulla@marvell.com> cc: Stefan Roese <sr@denx.de> Signed-off-by: Scott Wood <scottwood@freescale.com>
2011-10-03powerpc/p3060: Add SoC related support for P3060 platformShengzhou Liu
Add P3060 SoC specific information:cores setup, LIODN setup, etc The P3060 SoC combines six e500mc Power Architecture processor cores with high-performance datapath acceleration architecture(DPAA), CoreNet fabric infrastructure, as well as network and peripheral interfaces. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-03fm-eth: Add ability for board code to disable a portKumar Gala
The SoC configuration may have more ports enabled than a given board actually can utilize. Add a routinue that allows the board code to disable a port that it knows isn't being used. fm_disable_port() needs to be called before cpu_eth_init(). Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-03I2C: mv_i2c: fix multi-bus init issueLei Wen
When enable the multi-bus, the current_bus is not inited in the original implementation, which make the i2c operation unpredicatable. Signed-off-by: Lei Wen <leiwen@marvell.com>
2011-10-03I2C: mv_i2c: fix build issue when enable debug optionLei Wen
When DEBUG_I2C is open, the following build issue would shows up. mv_i2c.c: In function 'i2c_transfer': mv_i2c.c:257: error: 'ISR' undeclared (first use in this function) mv_i2c.c:257: error: (Each undeclared identifier is reported only once mv_i2c.c:257: error: for each function it appears in.) Signed-off-by: Lei Wen <leiwen@marvell.com>
2011-10-03net: emaclite: Use dynamic allocationMichal Simek
Every emaclite instance use own setting. Signed-off-by: Michal Simek <monstr@monstr.eu> Acked-by: Mike Frysinger <vapier@gentoo.org>
2011-10-03net: emaclite: Remove baseaddress from xemacliteMichal Simek
Use dev->iobase instead of baseaddress. Signed-off-by: Michal Simek <monstr@monstr.eu>
2011-10-03net: emaclite: Use calloc instead of mallocMichal Simek
Simplify driver logic and clear eth_device structure in one command. Signed-off-by: Michal Simek <monstr@monstr.eu>
2011-10-03net: emaclite: Remove deviceid propertyMichal Simek
Cleanup structure. Signed-off-by: Michal Simek <monstr@monstr.eu>
2011-10-03net: emaclite: Change driver name and add addressMichal Simek
Current xilinx emaclite use net multi registration but doesn't support several emaclites interfaces. Changing driver name with adding address to name is the first step how to distiguish several drivers. Signed-off-by: Michal Simek <monstr@monstr.eu>
2011-10-01GCC4.6: Squash warning in vmt.cMarek Vasut
vmt.c: In function ‘ubi_free_volume’: vmt.c:681:6: warning: variable ‘err’ set but not used [-Wunused-but-set-variable] Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Acked-by: Mike Frysinger <vapier@gentoo.org>
2011-10-01GCC4.6: Squash warning in nand_bbt.cMarek Vasut
nand_bbt.c: In function ‘search_bbt’: nand_bbt.c:465:6: warning: variable ‘bits’ set but not used [-Wunused-but-set-variable] Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Scott Wood <scottwood@freescale.com>
2011-10-01GCC4.6: Squash warnings in ipu_disp.cMarek Vasut
ipu_disp.c: In function ‘ipu_disp_set_global_alpha’: ipu_disp.c:1237:11: warning: variable ‘flow’ set but not used [-Wunused-but-set-variable] ipu_disp.c: In function ‘ipu_disp_set_color_key’: ipu_disp.c:1302:16: warning: variable ‘flow’ set but not used [-Wunused-but-set-variable] Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de>
2011-10-01console: Squelch pre-console output in console functionsGraeme Russ
There are some locations in the code which anticipate printf() being called before the console is ready by squelching printf() on gd->have_console. Move this squelching into printf(), vprintf(), puts() and putc(). Also make tstc() and getc() return 0 if console is not yet initialised Signed-off-by: Graeme Russ <graeme.russ@gmail.com> Tested-by: Simon Glass <sjg@chromium.org>
2011-10-01ns16550: change to allow 32 bit access to registersDave Aldridge
If CONFIG_SYS_NS16550_MEM32 is defined then 32 bit memory mapped access will be used to read/write the uart registers. This is especially useful for SoC devices that implement 16550 compatible uarts but that have peripheral access width constraints. Signed-off-by: Dave Aldridge <fovsoft@gmail.com>
2011-10-01Merge branch 'sf' of git://git.denx.de/u-boot-blackfinWolfgang Denk
* 'sf' of git://git.denx.de/u-boot-blackfin: sf: eon: add support for EN25Q32B parts cmd_sf: add "update" subcommand to do smart SPI flash update
2011-09-30ATA: Squash warnings in mxc_ata.Marek Vasut
mxc_ata.c: In function ‘set_ata_bus_timing’: mxc_ata.c:118: warning: dereferencing type-punned pointer will break strict-aliasing rules mxc_ata.c:125: warning: dereferencing type-punned pointer will break strict-aliasing rules mxc_ata.c:129: warning: dereferencing type-punned pointer will break strict-aliasing rules Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de>
2011-09-30I2C: mxc_i2c reworkMarek Vasut
Rewrite the mxc_i2c driver. * This version is much closer to Linux implementation. * Fixes IPG_PERCLK being incorrectly used as clock source * Fixes behaviour of the driver on iMX51 * Clean up coding style a bit ;-) Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Jason Hui <jason.hui@linaro.org> Acked-by: Jason Liu <jason.hui@linro.org> Acked-by: Heiko Schocher <hs@denx.de> Tested-by: Jason Liu <jason.hui@linro.org>
2011-09-30FEC: Move imx_get_mac_from_fuse() definition to fec_mxc.hMarek Vasut
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Ben Warren <biggerbadderben@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de>
2011-09-30FEC: Squish "got MAC from fuse" message, make it debug()Marek Vasut
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Ben Warren <biggerbadderben@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de>
2011-09-30FEC: Add timeout for chip resetMarek Vasut
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Ben Warren <biggerbadderben@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de>
2011-09-30FEC: Allow registering MII postconfiguration callbackMarek Vasut
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Ben Warren <biggerbadderben@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de>
2011-09-30FEC: Allow multiple FECesMarek Vasut
This patch allows user to register multiple FEC controllers. To preserve compatibility with older boards, the mxcfec_register() call is still in place. To use multiple controllers, new macro is in place, the mxcfec_register_multi(), which takes more arguments. The syntax is: mxcfec_register_multi(bd, FEC ID, FEC PHY ID on the MII bus, base address); To disable the fecmxc_register() compatibility stuff, define the macro CONFIG_FEC_MXC_MULTI. This will remove the requirement for defining IMX_FEC_BASE and CONFIG_FEC_MXC_PHYADDR. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Ben Warren <biggerbadderben@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de>
2011-09-30FEC: Abstract access to fec->eth in MII operationsMarek Vasut
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Ben Warren <biggerbadderben@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de>
2011-09-30FEC: Allow selection of MII mode via CONFIG_FEC_XCV_TYPEMarek Vasut
The default is MII100, which was hardcoded previously in the driver. Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Ben Warren <biggerbadderben@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de>
2011-09-30FEC: Add RMII mode supportMarek Vasut
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Ben Warren <biggerbadderben@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de>
2011-09-30FEC: Kill mode select FIXME'sMarek Vasut
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Ben Warren <biggerbadderben@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de>
2011-09-30FEC: Use defined constant instead of magic numberMarek Vasut
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Ben Warren <biggerbadderben@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de>
2011-09-30FEC: Use proper accessor to read register in debug callMarek Vasut
Signed-off-by: Marek Vasut <marek.vasut@gmail.com> Cc: Ben Warren <biggerbadderben@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Detlev Zundel <dzu@denx.de>
2011-09-30cosmetic: fsl_pmic: cosmetic for the help messageJason Liu
This is cosmetic patch for the help message: Before: pmic dump [numregs] dump registers After: pmic dump [numregs] - dump registers Signed-off-by: Jason Liu <jason.hui@linaro.org> Acked-by: Stefano Babic <sbabic@denx.de>
2011-09-30rtc, davinci: add support for davinci internal RTCHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Paulraj Sandeep <s-paulraj@ti.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-30net, davinci_emac: let the EMAC detect the PHYsHeiko Schocher
Once the MDIO state machine has been initialized and enabled, it starts polling all 32 PHY addresses on the MDIO bus, looking for an active PHY. Add a 5 ms delay, so all PHYs are for sure detected. This problem was detected on the cmc board with a KSZ8864 switch. Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
generated by cgit (git 2.34.1) at 2024-12-29 12:29:09 +0000