summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2019-04-16clk: sunxi: r40: Fix GMAC reset reg offsetJagan Teki
GMAC reset reg offset added by below commit seems to assume it as EMAC but R40 indeed using GMAC. "clk: sunxi: Implement EMAC, GMAC clocks, resets" (sha1: 68620c9698f109c1f001f80d282138a5c67cabef) So, fix by updating the reg offset for RST_BUS_GMAC. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-04-16net: gem: Remove phy autodetection codeMichal Simek
There is no reason to detect phy when core is doing it for us. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-04-16net: zynq_gem: Modify phy supported features after max-speed was setSiva Durga Prasad Paladugu
The phydev supported features were reset in phy_set_supported() so, move the setting of driver supported features after this so that it wont lost in phy_set_supported(). Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-04-16arm: zynq: Add an info message about post configSiva Durga Prasad Paladugu
Post configuration cant be run at u-boot as u-boot didn't has any info about the design.So,this patch adds an info message that post config was not run and needs to be run manually if needed. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-04-16ARM: zynq: Add missing i2c get_rate for fixing i2c SPLHannes Schmelzer
The commit 'f48ef0d81aa837a33020f8d61abb3929ba613774' did break I2C support because requesting the clock for the I2C ip-block isn't supported during SPL. To fixup this we add support requesting clocks for: - i2c0 - i2c1 Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Reviewed-by: Heiko Schocher <hs@denx.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-04-16spi: zynqmp_gqspi: Fix tap delay values at 100MHz and 150MHzSiva Durga Prasad Paladugu
This patch fixes the tap delay values to be set at 100MHz and 150MHz as per TRM by fixing the if condition to use <= instead of <. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-04-16fpga: Replace char * with const char * for filenameTien Fong Chee
Ensure the string for filename is always constant, otherwise it can be corrupted by the writing. Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-04-15Merge tag 'u-boot-imx-20190415' of git://git.denx.de/u-boot-imxTom Rini
Move to DM ----------- - DM support in sata - Toradex Board to DM - wandboard to DM - tbs2910 to DM - GE boards to DM - VHybrid boards to DM - DM_VIDEO for i.MX
2019-04-15Merge tag 'video-for-2019.07-rc1' of git://git.denx.de/u-boot-videoTom Rini
- optional backlight PWM polarity config via polarity cell - bug fix for ASCII characters > 127 - ANSI sequence handling extensions (implement clear line, reverse video and relative cursor movement commands) - preparation for doing character set translations - left/right and up/down arrow keys translation to ANSI control sequences for cursor movement to fix selection with an USB keyboard in bootmenu - CONFIG_SYS_WHITE_ON_BLACK font scheme configuration for sunxi boards
2019-04-14sunxi: allow boards to de-select SYS_WHITE_ON_BLACK font schemeAndre Przywara
In the sunxi-common.h config header we unconditionally define CONFIG_SYS_WHITE_ON_BLACK, although it's actually a Kconfig option which could be individually selected by a user. Remove this #define from the header and let it default to "y" on sunxi boards (like we do for other platforms). Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-04-14video/console: Factor out actual character outputAndre Przywara
In preparation for doing character set translations, factor out the actual glyph display functionality into a separate function. This will be used in a subsequent patch. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-04-14video/console: Implement ANSI clear line commandAndre Przywara
There is a standard ANSI terminal escape sequence to clear a whole line of text. So far the DM_VIDEO console was missing this code. Detect the sequence and use vidconsole_set_row with the background colour to fix this omission. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-04-14video/console: Implement relative cursor movement ANSI handlingAndre Przywara
The ANSI terminal escapce sequence standard defines relative cursor movement commands (ESC [ A-F). So far the DM_VIDEO console code was ignoring them. Interpret those sequences and move the cursor by the requested amount of rows or columns in the right direction. This brings the code on par with the legacy video console driver (cfb_console). Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-04-14video/console: Implement reverse video ANSI sequence for DM_VIDEOAndre Przywara
The video console for DM_VIDEO compliant drivers only understands a very small number of ANSI sequences. First and foremost it misses the "reverse video" command, which is used by our own bootmenu command to highlight the selected entry. To avoid forcing people to use their imagination when using the bootmenu, let's just implement the rather simple reverse effect. We need to store the background colour index for that, so that we can recalculate both the foreground and background colour pixel values. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org> [agust: merged BG color escape seq change to fix "ut dm video_ansi" test] Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-04-14video/console: Fix DM_VIDEO font glyph array indexingAndre Przywara
When the character to be printed on a DM_VIDEO console is from the "extended ASCII" range (0x80 - 0xff), it will be treated as a negative number, as it's declared as a signed char. This leads to negative array indicies into the glyph bitmap array, and random garbled characters. Cast the character to an unsigned type to make the index always positive and avoid an out-of-bounds access. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-04-14video: backlight: Parse PWM polarity cellStefan Mavrodiev
This patch enables the reading of the polarity cell from a PWM phandle and calls pwm_set_invert(). Not all platforms have polarity cell, so skip if it's not pressent. Signed-off-by: Stefan Mavrodiev <stefan@olimex.com> Reviewed-by: Anatolij Gustschin <agust@denx.de>
2019-04-14Merge branch 'master' of git://git.denx.de/u-boot-spiTom Rini
Conflicts: arch/arm/dts/armada-385-amc.dts arch/arm/dts/armada-xp-theadorable.dts arch/arm/dts/stm32mp157c-ev1-u-boot.dtsi Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-13configs: move CONFIG_MXC_OCOTP to KconfigMarcel Ziswiler
While commit 3e020f03e94f ("driver: misc: add MXC_OCOTP Kconfig entry") introduced a Kconfig entry it did not actually migrate all configurations to using it. As CONFIG_MXC_OCOTP was in mx{6/7}_common.h enable it by default on those architectures. Additionally, also enable it on ARCH_IMX8M and ARCH_VF610 where all current members enabled it through their legacy configuration header files. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-04-13configs: move CONFIG_USB_EHCI_VF to KconfigMarcel Ziswiler
Move CONFIG_USB_EHCI_VF to drivers/usb/host/Kconfig and update the one and only user thereof being colibri_vf. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-13Add missing space in commentMarcel Ziswiler
Spotted two missing spaces in comments. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2019-04-13video: move ipuv3 files to subdirectoryAnatolij Gustschin
Place ipuv3 files and headers in custom driver subdirectory. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-04-13video: ipuv3: add DM_VIDEO supportAnatolij Gustschin
Extend the driver to build with DM_VIDEO enabled. DTS files must additionally include 'u-boot,dm-pre-reloc' property in soc and ipu nodes to enable driver binding to ipu device. Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-04-13ata: dwc_ahsata: Add ahci driver model supportSoeren Moch
Disable this support for cm_fx6 to avoid breakage. Signed-off-by: Soeren Moch <smoch@web.de>
2019-04-13ata: dwc_ahsata: Fix sector reports for large disksSoeren Moch
Do not report negative sector numbers for disks > 1TB, do not limit sector numbers to 32 bit if CONFIG_SYS_64BIT_LBA is enabled. Signed-off-by: Soeren Moch <smoch@web.de>
2019-04-13net: Kconfig: FEC: Add dependency on VF610Lukasz Majewski
Signed-off-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
2019-04-13net: FEC: Add compatible for vybrid (vf610) to reuse fec_mxc.c driverLukasz Majewski
The NXP's FEC driver can be reused on vf610 device (with DM). Signed-off-by: Lukasz Majewski <lukma@denx.de> Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
2019-04-13Merge tag 'pull-12apr19' of git://git.denx.de/u-boot-dmTom Rini
fdtdec tests and improvements for carve-outs pinctrl race-condition fix various other fixes in sandbox, sound, mkimage, etc.
2019-04-13Merge tag 'mips-pull-2019-04-12' of git://git.denx.de/u-boot-mipsTom Rini
- mt76xx: add USB support, small fixes - ath79: small fixes, add support for QCA9563 SoC and AP152 reference board - mscc: small fixes, add network support for JR2 and ServalT SoCs - bmips: small fixes, enable more drivers for ARM specific BCM6858 and BCM63158 SoCs - MIPS: fix redundant relocation of initrd images
2019-04-12Merge tag 'u-boot-stm32-20190412' of https://github.com/patrickdelaunay/u-bootTom Rini
stm32 patches for v2019.07-rc1 - Add trusted boot with TF-A for stm32mp1 - stm32mp1 dts files sync'ed with Linux version - add STM32MP1 Discovery boards (DK1 and DK2) - add STMFX gpio expander driver - misc improvement for stm3mp1 supports - rename stpmu1 to stpmic1 (official name) - stm32_qspi: move to exec_op (spi nor driver for stm32 mpu and mcu) - add STM32 FMC2 NAND flash controller driver
2019-04-12Merge branch 'master' of git://git.denx.de/u-boot-i2cTom Rini
2019-04-12Merge git://git.denx.de/u-boot-marvellTom Rini
- Misc dts files sync'ed with Linux version (Chris) - Orion watchdog fix (Chris) - kwbimage changed to also support Marvell bin_hdr binary (Chris) - Add DM support to enable CONFIG_BLK for sata_mv (Stefan) - Enable BLK on multiple platforms (Stefan) - Misc minor fixes to AXP theadorable board (Stefan) - Correct logic for DM_SCSI + unconverted drivers check (stefan) - Misc changes to kirkwood to enable DM_USB here (Chris) - Change ahci_mvebu to enable usage on A38x (Baruch) - Update the kirkwood entry in git-mailrc (Baruch) - Misc minor improvements (turris, documentation) (Baruch) - Enhance sata_mv to support Kirkwood as well (Michael) - Add wdt command (Michael) - Add Marvell integrated CPUs (MSYS) support with DB-XC3-24G4XG board support (Chris)
2019-04-12phy: Add USB PHY driver for the MT76x8 (7628/7688) SoCStefan Roese
This driver is derived from this Linux driver: linux/drivers/phy/ralink/phy-ralink-usb.c The driver sets up power and host mode, but also needs to configure PHY registers for the MT7628 and MT7688. I removed the reset controller handling for the USB host and device, as it does not seem to be necessary right now. The soft reset bits for both devices are enabled by default and testing has shown (with hackish reset handling added), that USB related commands work identical with or without the reset handling. Please note that the resulting USB support is tested only very minimal. I was able to detect one of my 3 currently available USB sticks. Perhaps some further work is needed to fully support the EHCI controller integrated in the MT76x8 SoC. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Marek Vasut <marex@denx.de> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2019-04-12net: Add MSCC ServalT network driver.Horatiu Vultur
Add network driver for Microsemi Ethernet switch. It is present on ServalT SoCs. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2019-04-12net: Add MSCC Jaguar2 network driver.Horatiu Vultur
Add network driver for Microsemi Ethernet switch. It is present on Jaguar2 SoCs. Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
2019-04-12gpio: bcm6345: allow this driver on ARCH_BCM63158Philippe Reynes
This IP is also used on some arm SoC, so we allow to use this driver on arch bcm63158. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-12gpio: bcm6345: allow this driver on ARCH_BCM6858Philippe Reynes
This IP is also used on some arm SoC, so we allow to use this driver on arch bcm6858. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-04-12gpio: bcm6345: switch to raw I/O functionsPhilippe Reynes
This driver is used on several big endian mips board. So we could use raw I/O function instead of forcing big endian access. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2019-04-12ag7xxx: add initial support for s17Rosy Song
S17 ethernet support is for QCA8337N, which used on AP152 (QCA9563) board. It is a 7 ports GbE switch. Signed-off-by: Rosy Song <rosysong@rosinson.com> Changes for v2-v3: - add more commit message for s17 Changes for v4-v5: - coding style cleanup
2019-04-12dma: bcm6348: check if driver is enabled before send/recvÁlvaro Fernández Rojas
This patch prevents errors when running tftpput. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2019-04-12net: mscc: ocelot: Fix reset of the physHoratiu Vultur
The function mscc_miim_reset resets all the phys, but it is called for each phy separetely. One consequence of this is that the boot time is increased by 2 seconds. The fix consists for calling the mscc_miim_reset function only once for all phys. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2019-04-12drivers: add ethernet support for qca953x in ag7xxx driverRosy Song
Signed-off-by: Rosy Song <rosysong@rosinson.com>
2019-04-12drivers: fix typo for pinctrl qca953xRosy Song
Signed-off-by: Rosy Song <rosysong@rosinson.com>
2019-04-12mtd: rawnand: stm32_fmc2: add STM32 FMC2 NAND flash controller driverChristophe Kerello
The driver adds the support for the STMicroelectronics FMC2 NAND Controller found on STM32MP SOCs. This patch adds the polling mode, a basic mode that do not need any DMA channels. Only NAND_ECC_HW mode is actually supported. The driver supports a maximum 8k page size. The following ECC strength and step size are currently supported: - nand-ecc-strength = <8>, nand-ecc-step-size = <512> (BCH8) - nand-ecc-strength = <4>, nand-ecc-step-size = <512> (BCH4) - nand-ecc-strength = <1>, nand-ecc-step-size = <512> (Extended ECC based on Hamming) This patch has been tested on Micron MT29F8G08ABACAH4. Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
2019-04-12spi: stm32_qspi: move to exec_opChristophe Kerello
We are facing issues in the driver since SPI NOR framework has moved on SPI MEM framework, and SPI NAND framework is not running properly with the current driver. To be able to solve issues met on SPI NOR Flashes and to be able to support SPI NAND Flashes, the driver has been reworked. We are now using exec_op ops instead of using xfer ops. Thanks to this rework, the driver has been successfully tested with: - mx66l51235l SPI NOR Flash on stm32f746 SOC - n25q128a SPI NOR Flash on stm32f769 SOC - mx66l51235l SPI NOR Flash on stm32mp1 SOC - mt29f2g01abagd SPI NAND Flash on stm32mp1 SOC Signed-off-by: Christophe Kerello <christophe.kerello@st.com> Tested-by: Patrick DELAUNAY <patrick.delaunay@st.com> Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
2019-04-12pinctrl: Add STMFX GPIO expander Pinctrl/GPIO driverPatrick Delaunay
This patch adds pinctrl/GPIO driver for STMicroelectronics Multi-Function eXpander (STMFX) GPIO expander. STMFX is an I2C slave controller, offering up to 24 GPIOs. The driver relies on UCLASS_PINCTRL and UCLASS_GPIO. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-04-12stpmic1: add NVM update support in fuse commandPatrick Delaunay
Add functions to read/update the non volatile memory of STPMIC1 (8 bytes-register at 0xF8 address) and allow access with fuse command (bank=1, word > 0xF8). For example: STM32MP> fuse read 1 0xf8 8 Reading bank 1: Word 0x000000f8: 000000ee 00000092 000000c0 00000002 Word 0x000000fc: 000000f2 00000080 00000002 00000033 Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12pmic: stpmu1: add power switch off supportPatrick Delaunay
Add sysreset support, and support power switch off request, needed by poweroff command. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12stpmic1: update register namesPatrick Delaunay
Alignment with STPMIC1 datasheet s/MAIN_CONTROL_REG/MAIN_CR/g s/MASK_RESET_BUCK/BUCKS_MRST_CR/g s/MASK_RESET_LDOS/LDOS_MRST_CR/g s/BUCKX_CTRL_REG/BUCKX_MAIN_CR/g s/VREF_CTRL_REG/REFDDR_MAIN_CR/g s/LDOX_CTRL_REG/LDOX_MAIN_CR/g s/USB_CTRL_REG/BST_SW_CR/g s/STPMIC1_NVM_USER_STATUS_REG/STPMIC1_NVM_SR/g s/STPMIC1_NVM_USER_CONTROL_REG/STPMIC1_NVM_CR/g and update all the associated defines. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-04-12power: rename stpmu1 to official name stpmic1Patrick Delaunay
Alignment with kernel driver name & binding introduced by https://patchwork.kernel.org/cover/10761943/ to use the final marketing name = STPMIC1. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
2019-04-12power: stpmu1: rename files to stpmic1Patrick Delaunay
Prepare file modification for kernel alignment and rename driver to stpmic1. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Lukasz Majewski <lukma@denx.de>
generated by cgit (git 2.34.1) at 2024-12-29 09:28:53 +0000