| Age | Commit message (Collapse) | Author |
|---|
|
The call to flush cache on the transmit buffer was misplaced (for very
short packets) and asked to flush less than a cacheline.
Move the flush cache call to after a short packet has been padded
to minimum length (so the padding is flushed too), and round the size
up to a cacheline.
Signed-off-by: Peter Chubb <peter.chubb@data61.csiro.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
On some boards these switches are wired directly into a SERDES
interface on another Ethernet MAC. Add the ability to specify
these kinds of boards using CONFIG_MV88E61XX_FIXED_PORTS which defines
a bit mask of these fixed ports.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
The Marvell Link Street mv88e60xx is a series of FastEthernet switch
chips, some of which also support Gigabit ports. It is similar to the
mv88e61xx series which support Gigabit on all ports.
The main difference is the number of ports. Which affects the
PORT_COUNT define and the size of the mask passed to
mv88e61xx_port_set_vlan().
Other than that it's just a matter of adding the appropriate chip
IDs.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Cc: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
source selection
cpsw driver supports only selection of phy mode in control module
but control module has more setting like RGMII ID mode selection,
RMII clock source selection. So ported to cpsw-phy-sel driver
from kernel to u-boot.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
In the current driver implementation, config() callback is common
for AR8035 and AR8031 phy. In config() callback, driver tries to
configure MMD Access Control Register and MMD Access Address Data
Register unconditionally for both phy versions which leads to
auto negotiation failure in AM335x EVMsk second port which uses
AR8031 Giga bit RGMII phy. Fixing this by adding separate config
for AR8031 phy.
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
This adds support for internal delay on RX and TX on RGMII interface for the
AR8035 phy.
This is basically the same Linux driver do. Tested on a Zynq Zturn board (for
which u-boot support in is my tree; first patch waiting ML approval)
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
|
|
|
|
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
Conflicts:
include/configs/ls1021aqds.h
include/configs/ls1021atwr.h
|
|
Now that all x86 boards have been converted to DM video, drop the
legacy drivers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This converts coreboot to use DM framebuffer driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
With DM VESA driver on x86 boards, plat->base/size/align are all
zeroes and starting address passed to alloc_fb() happens to be 1MB
aligned, so this routine does not trigger any issue. On QEMU with
U-Boot as coreboot payload, the starting address is within 1MB
range (eg: 0x7fb0000), thus causes failure in video_post_bind().
Actually if plat->size is zero, it makes no sense to do anything
in this routine. Add such check there.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This adds a DM driver for coreboot framebuffer device.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
vbe_setup_video_priv() might be useful to other drivers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
At present only chromebook boards are converted to DM video. Other
x86 boards are still using the legacy cfb_console driver. This
switches to use DM version drivers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
With DM conversion, information like "Video: 1024x768x16" is not
shown anymore. Now add these verbose output back.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This adds a DM driver for VESA-compatible device.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This gives a build warning on 64-bit x86. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Fix a cast that causes warnings on 64-bit machines.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
We should consistently use %z with size_t, and avoid passing a uint32_t as
a size_t value. Fix these issues to avoid warnings on 64-bit machines.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
For 64-bit x86, __I386__ should perhaps not be defined. It is not clear from
the definition, but let's use CONFIG_X86 to be sure.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Fix a cast that causes warnings on 64-bit machines.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Update the samus driver to avoid the direct call to the video BIOS setup.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
At present we use the legacy vesa driver for graphics. Add a driver which
supports driver model. This can be probed only when needed, removing the
need to start up the display if it is not used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
Provide a function to run the Vesa BIOS for a given PCI device and obtain
the resulting configuration (e.g. display size) for use by the video
uclass. This makes it easier to write a video driver that uses vesa and
supports driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
'enabled' should be 'enables'. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
It is useful in debug() statements to display the name of the uclass for a
device. Add a simple function to provide this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This makes the assumption that setting up pinctrl in cpu_init_r() is safe.
On samus we need GPIOs before relocation in order to support power control.
This commit fixes the following message on boot:
initcall sequence ffe5c6f4 failed at call ffe01d3d (err=-1)
### ERROR ### Please RESET the board ###
In any case it seems better to leave init to driver model, so that it can
pick up the GPIO driver when it needs it. Since pinctrl is a dependency of
the GPIO driver, we may as well put the dependency there and avoid these
problems.
This reverts commit 9769e05bcf79939bad23a719982dd1f85a110f3c.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
According to the binding documentation the fixed regulator enable GPIO
is optional. However so far registration thereof failed if no enable
GPIO was specified. Fix this by making it entirely optional whether an
enable GPIO is used.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
Fix spelling of debug message from cnnot to cannot.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
|
|
This is the initial commit for UniPhier reset controller driver.
Most code was ported from Linux.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
|
|
By default saveenv option is not supported for SPL. This patch
enable the support for save environment variable for SPL build.
Enable save environment support in SPL after setenv. By default
the saveenv option is not provided in SPL, but some boards need
this support in 'Falcon' boot, where SPL need to boot from
different images based on environment variable set by OS. For
example OS may set "reboot_image" environment variable to
"recovery" inorder to boot recovery image by SPL. The SPL read
"reboot_image" and act accordingly and change the reboot_image
to default mode using setenv and save the environemnt.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Simon Glass <sig@chromium.org>
change in v1:
- dropped SUPPORT, use CONFIG_SPL_SAVEENV
- updates the comments in mmc_private.h
|
|
Boards where ECs that use a I2C port != 0 specify this in the
devicetree file via the google,remote-bus property.
Previously this was ignored and hardcoded to port 0.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: u-boot@lists.denx.de
Acked-by: Simon Glass <sjg@chromium.org>
|
|
This reverts commit 82f5279b0cd99a9163d34cfe926d0316d9dc0d37.
The build failure of k2*evm boards was fixed in a different way by
the previous commit. It is nasty to patch generic drivers around
with #ifdef CONFIG_CLK just for the KeyStone's matter.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Add device model enabled PMIC driver for Ricoh RN5T567 PMIC used
on Colibri iMX7.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
It is not usual that drivers announce when they have been initialized.
use dev_dbg to announce device initialization.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Support instatiation through device tree. Also parse the fsl,dte-mode
property to determine whether DTE mode shall be used.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Acked-by: Heiko Schocher <hs@denx.de>
|
|
Fix various misspellings of:
* deprecated
* partition
* preceding,preceded
* preparation
* its versus it's
* export
* existing
* scenario
* redundant
* remaining
* value
* architecture
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
|
|
The endianness can be changed by RCW + PBI sequence. It may have
other than power on reset value.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Yuan Yao <yao.yuan@nxp.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
|
|
Update the ext loader to avoid using the spl_image global variable.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
At present there are two SPI functions only used by freescale which are
defined in the spi_flash.h header. One function name matches an existing
generic SPL function.
Move these into a private header to avoid confusion.
Arcturus looks like it does not actually support SPI, so drop the SPI code
from that board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Add a linker list declaration for this method and remove the explicit
switch() code. Also set up the sunxi function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
All the other SPL loaders are in this directory, so move the SPI one in
there too.
There are two board-specific SPI loaders (fsl and sunxi). These remain in
the drivers/mtd/spi directory, since they do not contain generic code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
At present some spl_xxx_load_image() functions take a parameter and some
don't. Of those that do, most take an integer but one takes a string.
Convert this parameter into a struct so that we can pass all functions the
same thing. This will allow us to use a common function signature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Instead of using the global spl_image variable, pass the required struct in
as an argument.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
Update the API's for transition of Security Monitor states. Instead
of providing both initial and final states for transition, just
provide final state for transition as Security Monitor driver will
take care of it internally.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
[York Sun: Reformatted commit message slightly]
Reviewed-by: York Sun <york.sun@nxp.com>
|
