| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch removes some problems when the Xilinx SystemACE driver
is used with 16bit access on an big endian platform (like the
AMCC Katmai).
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
buffer pointers
Block device read/write is anonymous data; there is no need to use a
typed pointer. void * is fine. Also add a hook for block_read functions
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Register read/write does not need to be wrapped in a full function. The
patch replaces them with macros.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
The code in this file is not a command; it is a device driver. Put it in
the correct place. There are zero functional changes in this patch, it
only moves the file.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Conflicts:
drivers/cfi_flash.c
The patch by Heiko Schocher <hs@pollux.denx.de> on Jan, 19, 2007
fixes cfi_driver bug for mpc7448hpc2 board. The default cfi_driver can support
mpc7448hpc2 board.
|
|
if you must swap the bytes between reading/writing.
(Needed for the SC3 board)
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
The EBC Configuration Register is now by CFG_EBC_CFG definable
Added JFFS2 support for the SC3 board.
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
Some code cleanup.
|
|
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
Here the description from Brian Brelsford <Brian_Brelsford@dell.com>:
The Hynix part returns a 0x1d in the 4th ID byte. The Samsung part
returns a 0x15. In the code fragment below bits [1:0] determine the
page size, it is ANDed via "(extid & 0x3)" then shifted out. The
next field is also ANDed with 0x3. However this is a one bit field
as defined in the Hynix and Samsung parts in the 4th ID byte that
determins the oobsize, not a two bit field. It works on Samsung as
bits[3:2] are 01. However for the Hynix there is a 11 in these two
bits, so the oob size gets messed up.
I checked the correct linux code and the suggested fix from Brian is
also available in the linux nand mtd driver.
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
|
|
|
|
|
|
|
|
offset to go into CFI mode)
|
|
Signed-off-by: Heiko Schocher <hs@denx.de>
|
|
The conflicts due to a new mpc7448 p3m7448 board is in the main tree.
Merge branch 'master' into hpc2
Conflicts:
MAKEALL
cpu/74xx_7xx/cpu.c
cpu/74xx_7xx/cpu_init.c
cpu/74xx_7xx/speed.c
|
|
(1) remove some C++ comments.
(2) remove trailing white space.
(3) remove trailing empty line.
(4) Indentation by table.
(5) remove {} in one line condition.
(6) add space before '(' in function call.
Remove some weird printf () output.
Add necessary comments.
Modified Makefile to support building in a separate directory.
|
|
|
|
|
|
Signed-off-by: Timur Tabi <timur@freescale.com>
|
|
Signed-off-by: Timur Tabi <timur@freescale.com>
|
|
|
|
give initial values for reg_num, shift, p_cmxucr in ucc_set_clk_src
since they are passed by reference to ucc_get_cmxucr_reg and assigned.
|
|
Merge branch 'master' into hpc2
Conflicts:
drivers/cfi_flash.c
|
|
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
|
|
Two fixes for the nand_wait() function in
drivers/nand/nand_base.c:
1. Use correct timeouts. The original timeouts in Linux
source are 400ms and 20ms not 40s and 20s
2. Return correct error value in case of timeout. 0 is
interpreted as OK.
Signed-off-by: Rui Sousa <rui.sousa@laposte.net>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
|
|
|
|
|
|
|
|
to choose between the old and the generic OHCI drivers.
|
|
and adapted board configs TQM5200 and yosemite accordingly. This commit
also makes the maximum number of root hub ports configurable
(CFG_USB_OHCI_MAX_ROOT_PORTS).
|
|
* Adds support for AMD command set Top Boot flash geometry reversal
* Adds support for reading JEDEC Manufacturer ID and Device ID
* Adds support for displaying command set, manufacturer id and
device ids (flinfo)
* Makes flinfo output to be consistent when CFG_FLASH_EMPTY_INFO defined
* Removes outdated change history (refer to git log instead)
Signed-off-by: Tolunay Orkun <listmember@orkun.us>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
|
|
Update the 83xx tree to use I2C support in drivers/fsl_i2c.c. Delete
cpu/mpc83xx/i2c.c, include/asm-ppc/i2c.h, and all references to those files.
Added multiple I2C bus support to fsl_i2c.c.
Signed-off-by: Timur Tabi <timur@freescale.com>
|
|
Replace all instances of CFG_IMMRBAR with CFG_IMMR, so that the 83xx
tree matches the other 8xxx trees.
Signed-off-by: Timur Tabi <timur@freescale.com>
|
|
this patch adds support for the QUICC Engine based UCC gigabit ethernet device.
|
|
PREREQUISITE PATCHES:
* This patch can only be applied after the following patches have been applied:
1) DNX#2006090742000024 "Add support for multiple I2C buses"
2) DNX#2006090742000033 "Multi-bus I2C implementation of MPC834x"
3) DNX#2006091242000041 "Additional MPC8349 support for multibus i2c"
4) DNX#2006091242000078 "Add support for variable flash memory sizes on 83xx systems"
5) DNX#2006091242000069 "Add support for Errata DDR6 on MPC 834x systems"
CHANGELOG:
* Add support for the Freescale MPC8349E-mITX reference design platform.
The second TSEC (Vitesse 7385 switch) is not supported at this time.
Signed-off-by: Timur Tabi <timur@freescale.com>
|
|
This patch addresses a problem when CONFIG_MTD_NAND_VERIFY_WRITE is
defined
and the write crosses a block boundary. The pointer to the verification
buffer (bufstart) is not being updated to reflect the starting of the
new
block so the verification of the second block fails.
CHANGELOG:
* Fix NAND FLASH page verification across block boundaries
|
|
Added a phy initialization to adjust the RGMII RX and TX timing
Always set the R100 bit in 100 BaseT mode regardless of the TSEC mode
Signed-off-by: Nick Spence <nick.spence@freescale.com>
|
|
titled "CFI Driver Little-Endian write Issue".
http://sourceforge.net/mailarchive/message.php?msg_id=36311999
If that patch applied, please discard this one.
Until now , I do not see his patch is applied. So please apply this one.
Signed-off-by: Yuli Barcohen <yuli@arabellasw.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
|
|
The i2c Interface provides a master-only, serial interface that can be
used for initializing Tsi108/Tsi109 registers from an EEPROM after a
device reset.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
|
|
If there is no pci card, the tsi108/109 pci configure read will
cause a machine check exception to the processor. PCI error should
also be cleared after the read.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
|
|
The following is a brief description of the Ethernet controller:
The Tsi108/9 Ethernet Controller connects Switch Fabric to two independent
Gigabit Ethernet ports,E0 and E1. It uses a single Management interface
to manage the two physical connection devices (PHYs). Each Ethernet port
has its own statistics monitor that tracks and reports key interface
statistics. Each port supports a 256-entry hash table for address
filtering. In addition, each port is bridged to the Switch Fabric
through a 2-Kbyte transmit FIFO and a 4-Kbyte Receive FIFO.
Each Ethernet port also has a pair of internal Ethernet DMA channels to
support the transmit and receive data flows. The Ethernet DMA channels
use descriptors set up in memory, the memory map of the device, and
access via the Switch Fabric. The Ethernet Controller?s DMA arbiter
handles arbitration for the Switch Fabric. The Controller also
has a register businterface for register accesses and status monitor
control.
The PMD (Physical Media Device) interface operates in MII, GMII, or TBI
modes. The MII mode is used for connecting with 10 or 100 Mbit/s PMDs.
The GMII and TBI modes are used to connect with Gigabit PMDs. Internal
data flows to and from the Ethernet Controller through the Switch Fabric.
Each Ethernet port uses its transmit and receive DMA channels to manage
data flows through buffer descriptors that are predefined by the
system (the descriptors can exist anywhere in the system memory map).
These descriptors are data structures that point to buffers filled
with data ready to transmit over Ethernet, or they point to empty
buffers ready to receive data from Ethernet.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
|
|
1. Add 7447A and 7448 processor support.
2. Add the following flags.
CFG_CONFIG_BUS_CLK : If the 74xx bus frequency can be configured dynamically
(such as by switch on board), this flag should be set.
CFG_EXCEPTION_AFTER_RELOCATE: If an exception occurs after the u-boot
relocates to RAM, this flag should be set.
CFG_SERIAL_HANG_IN_EXCEPTION: If the print out function will cause the
system hang in exception, this flag should be set.
There is a design issue for tsi108/109 pci configure read. When pci scan
the slots, if there is no pci card, the tsi108/9 will cause a machine
check exception for mpc7448 processor.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
|
|
chpart, nboot and NAND subsystem related commands now accept also partition
name to specify offset.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
to a TSEC (e.g. a switch is connected via RMII) or
if the PHY is defective/incorrectly configured.
Signed-off-by: Ben Warren <bwarren@qstreams.com>
|
