summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2016-01-14spi: kirkwood_spi.c: Prepare for driver model supportStefan Roese
This patch prepares the Kirkwood SPI driver, also used on the MVEBU board (Armada XP / 38x), for the conversion to driver model. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Valentin Longchamp <valentin.longchamp@keymile.com> Cc: Luka Perkov <luka.perkov@sartura.hr> Cc: Jagan Teki <jteki@openedev.com> Cc: Simon Glass <sjg@chromium.org>
2016-01-14arm: mvebu: ddr: Fix compilation warningStefan Roese
gcc 5.1 generates this new warning (for Armada 38x platforms): drivers/ddr/marvell/a38x/ddr3_debug.c: In function 'hws_ddr3_tip_read_training_result': drivers/ddr/marvell/a38x/ddr3_debug.c:177:40: warning: 'sizeof' on array function parameter 'result' will return size of 'enum hws_result (*)[1]' [-Wsizeof-array-argument] memcpy(result, training_result, sizeof(result)); ^ drivers/ddr/marvell/a38x/ddr3_debug.c:171:31: note: declared here u32 dev_num, enum hws_result result[MAX_STAGE_LIMIT][MAX_INTERFACE_NUM]) ^ Since this functions is not referenced anywhere, lets just remove it. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Luka Perkov <luka.perkov@sartura.hr>
2016-01-13net: lpc32xx: fix ignored MDIO busy wait status on readVladimir Zapolskiy
The change fixes PHY write operation, which incorrectly waits for released busy state before issuing a write operation, this breaks sequential write/read operation logic, because read operation starts immediately on request and it completes, when busy state is gone. Instead of adding the second preceding busy state check to read function, do busy state release check after issuing a write operation, this method of operation is also recommended by the LPC32xx User's Manual, see MII Mgmt Indicators Register notes: For PHY Write if scan is not used: 1. Write 0 to MCMD 2. Write PHY address and register address to MADR 3. Write data to MWTD 4. Wait for busy bit to be cleared in MIND Reported-by: Alexandre Messier <amessier@tycoint.com> Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Tested-by: Alexandre Messier <amessier@tycoint.com>
2016-01-13serial: lpc32xx hsuart: port driver to driver modelVladimir Zapolskiy
The change ports NXP LPC32xx 14-clock UART device driver to driver model. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2016-01-13ums: support multiple LUNs at onceStephen Warren
Extend the ums command to accept a list of block devices. Each of these will be exported as a separate LUN. An example use-case would be: ums 0 mmc 0,0.1,0.2 ... which would export LUNs for eMMC 0's user data, boot0, and boot1 HW partitions. This is useful since it allows the host access to everything on the eMMC without having to somehow stop the ums command from executing and restart it with different parameters. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-13mmc: store hwpart in the block deviceStephen Warren
This will allow us to have multiple block device structs each referring to the same eMMC device, yet different HW partitions. For now, there is still a single block device per eMMC device. As before, this block device always accesses whichever HW partition was most recently selected. Clients wishing to make use of multiple block devices referring to different HW partitions can simply take a copy of this block device once it points at the correct HW partition, and use each one as they wish. This feature will be used by the next patch. In the future, perhaps get_device() could be enhanced to return a dynamically allocated block device struct, to avoid the client needing to copy it in order to maintain multiple block devices. However, this would require all users to be updated to free those block device structs at some point, which is rather a large change. Most callers of mmc_switch_part() wish to permanently switch the default MMC block device's HW partition. Enhance mmc_switch_part() so that it does this. This removes the need for callers to do this. However, common/env_mmc.c needs to save and restore the current HW partition. Make it do this more explicitly. Replace use of mmc_switch_part() with mmc_select_hwpart() in order to remove duplicate code that skips the call if that HW partition is already selected. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-13block: pass block dev not num to read/write/erase()Stephen Warren
This will allow the implementation to make use of data in the block_dev structure beyond the base device number. This will be useful so that eMMC block devices can encompass the HW partition ID rather than treating this out-of-band. Equally, the existence of the priv field is crying out for this patch to exist. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-13Merge branch 'master' of git://www.denx.de/git/u-boot-microblazeTom Rini
2016-01-13Merge git://git.denx.de/u-boot-netTom Rini
2016-01-13dm: core: Add a new api to get indexed device addressMugunthan V N
Add new api to get device address based on index. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Acked-by: Jagan Teki <jteki@openedev.com> [Rebased on master] Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13drivers: spi: ti_qspi: convert driver to adopt device driver modelMugunthan V N
adopt ti_qspi driver to device driver model Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-01-13spi: Add support for dual and quad modeMugunthan V N
spi bus can support dual and quad wire data transfers for tx and rx. So defining dual and quad modes for both tx and rx. Also add support to parse bus width used for spi tx and rx transfers. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Jagan Teki <jteki@openedev.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13drivers: spi: ti_qspi: prepare driver for DM conversionMugunthan V N
Prepare driver for DM conversion. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-01-13drivers: spi:ti_qspi: change ti_qspi_slave to ti_qspi_priv for driver model ↵Mugunthan V N
conversion Changing the ti_qspi_priv structure and its instance names from to priv for driver mode conversion. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-01-13drivers: spi: ti_qspi: do not hard code chip select for memory map configurationMugunthan V N
To enable memory map in dra7xx, specific chip select must be written to control module register. But this hard coded to chip select 1, fixing it by writing the specific chip select value to control module register. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Make IO modes at last in read modesJagan Teki
SLOW, FAST, DUAL, DUAL_IO, QUAD, QUAD_IO changed order to SLOW, FAST, DUAL, QUAD, DUAL_IO, QUAD_IO Cc: Simon Glass <sjg@chromium.org> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Tested-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13spi: Rename op_mode_rx to mode_rxJagan Teki
Since spi rx mode macro's are renamed to simple and meaninfull, this patch will rename the respective structure members. Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Tested-by: Jagan Teki <jteki@openedev.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13spi: Rename SPI_OPM_RX_* to SPI_RX_*Jagan Teki
SPI_OPM_RX_AS - SPI_RX_SLOW SPI_OPM_RX_AF - SPI_RX_FAST SPI_OPM_RX_DOUT - SPI_RX_DUAL SPI_OPM_RX_QOF - SPI_RX_QUAD Cc: Simon Glass <sjg@chromium.org> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Write quad bit along with read statusJagan Teki
While setting quad bit on spansion, macronix code is writing only particular quad bit this may give wrong functionality with other register bits, So this patch fix the issue where it with write previous read reg status along particular quad bit. Cc: Vignesh R <vigneshr@ti.com> Cc: Mugunthan V N <mugunthanvnm@ti.com> Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Read back and check once macronix quad bit setJagan Teki
One macronix quad bit set using SR, it's good to read back and check the written bit and also if it's already been set check for the bit and return. Cc: Vignesh R <vigneshr@ti.com> Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Read back and check once spansion quad bit setJagan Teki
One spansion quad bit set using CR, it's good to read back and check the written bit and also if it's already been set check for the bit and return. Cc: Vignesh R <vigneshr@ti.com> Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Tested-by: Mugunthan V N <mugunthanvnm@ti.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Fix quad bit set for micron devicesJagan Teki
Setting up quad bit for micron devices need to do the same way as other flash devices like spansion, winbond etc does using enhanced volatile config register so this patch adds this support instead of printing "QEB is volatile" Cc: Simon Glass <sjg@chromium.org> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Peter Pan <peterpandong@micron.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Use BIT macroJagan Teki
Used BIT macro like 1 << nr as BIT(nr) where nr is 0...n Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Minor cleanupJagan Teki
- Tab space - Place all read commands at one place. - Re-arrange write commands. Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Remove spi_flash_removeJagan Teki
Use direct call to device_remove instead of exctra spi_flash_remove defination. Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Rename bank_end to bar_end in read_barJagan Teki
bar_end gives more meaningfull compared to bank_end and spi_flash_write_bar uses bar_end so replaced bank_end with bar_end in spi_flash_read_bar Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Rename spi_flash_set_* functionsJagan Teki
Since quad_mode functions are local to spi flash core, rename them to a meaningful and readable names. Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Move spi_read_cmds_array locallyJagan Teki
Since spi_read_cmds_array is used locally in spi_flash_scan, so move array to locally used function instead of defining global array. Tested-by: Jagan Teki <jteki@openedev.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13spi: Rename SPI_TX_BP|QPP to SPI_TX_BYTE|QUADJagan Teki
Since SPI_TX_* are spi_slave{} members so use spi protocol notation instead spi flash programming, like SPI_TX_BP => SPI_TX_BYTE SPI_TX_QPP => SPI_TX_QUAD Cc: Simon Glass <sjg@chromium.org> Tested-by: Jagan Teki <jteki@openedev.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13spi: Use mode instead of op_mode_txJagan Teki
Used mode member from spi_slave{} instead of op_mode_tx. Cc: Simon Glass <sjg@chromium.org> Tested-by: Jagan Teki <jteki@openedev.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13sf: Get spi locally from spi_flashJagan Teki
For better code readabilty, get the spi pointer from spi_flash{} locally and use it instead of direct dereferring spi pinter as flash->spi->* Tested-by: Jagan Teki <jteki@openedev.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Jagan Teki <jteki@openedev.com>
2016-01-13spl: dm: Add SPL_DM_SEQ_ALIAS config optionNathan Rossi
The Device Model sequence alias feature is required by some Uclasses. Instead of disabling the feature for all SPL targets allow it to be configured. The config option is disabled by default to reduce code size for targets that are not interested or do not require this feature. Signed-off-by: Nathan Rossi <nathan@nathanrossi.com> Acked-by: Simon Glass <sjg@chromium.org> Acked-by: Michal Simek <michal.simek@xilinx.com> Cc: Simon Glass <sjg@chromium.org> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Marek Vasut <marex@denx.de> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-12dm: core: Add option to configure an offset for the address translationStefan Roese
Some platforms need to ability to configure an offset to the standard addresses extracted from the device-tree. This patch allows this by adding a function to DM to configure this offset (if needed). Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Simon Glass <sjg@chromium.org> Cc: Simon Glass <sjg@chromium.org> Fixed space before tab: Signed-off-by: Simon Glass <sjg@chromium.org>
2016-01-12dm: ns16550: Allow the driver to be omitted if requestedSimon Glass
Allow the ns16550 debug UART to be used without the full driver. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
2016-01-12dm: serial: Allow the UART driver to be dropped from the imageSimon Glass
In very very space-constrained devices even the full UART driver is too large. In this case the debug UART can still be used in some cases. Add options to enable the UART driver in SPL and U-Boot proper. Enable both options by default. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
2016-01-12dm: net: usb: Convert mcs7830 driver to support driver modelSimon Glass
Adjust this driver to support driver model for Ethernet. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-12dm: net: usb: Refactor mcs7830 driver ready for DM conversionSimon Glass
Remove stamp data and create common functions for the main Ethernet operations. This will make it easier to convert this driver to support driver model. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-12pci: Tidy up comments in pci_bind_bus_devices()Simon Glass
The current comments are confusing. We don't actually bind a generic device when the device tree has no information. We try to scan available PCI drivers. Update the comments to reflect this. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12dm: Convert PCI MMC over to use DM PCI APISimon Glass
At present pci_mmc_init() does not correctly use the PCI function since the list it passes is not terminated. The array size passed to pci_mmc_init() is actually not used correctly. Fix this and adjust the pci_mmc_init() to scan all available MMC devices. Adjust this code to use the new driver model PCI API. This should move over to the new MMC uclass at some point. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12dm: usb: Convert echi-pci to use new DM PCI APISimon Glass
Convert this driver to use the new driver model PCI API. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Marek Vasut <marex@denx.de>
2016-01-12dm: ahci: Convert to use new DM PCI APISimon Glass
Convert this driver to use the new driver model PCI API. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12dm: pci: Switch to DM API for PCI address mappingSimon Glass
We should use the new address mapping functions unless we are in compatibility mode. Disable the old functions by default. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12dm: net: Convert rtl8169 to use DM PCI APISimon Glass
Update this driver to use the proper driver-model PCI API functions. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-12dm: pci: Add driver model API functions for address mappingSimon Glass
At present the PCI address map functions use the old API. Add new functions for this so that drivers can be converted. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12dm: pci: Drop the old version of pci_find_class()Simon Glass
Move this function into the compatibility file so that it is not available by default. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12dm: pci: Drop the old version of pci_find_device/s()Simon Glass
Move these functions into the compatibility file so that they are not available by default. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12dm: x86: pci: Adjust bios_run_on_x86() to use the DM PCI APISimon Glass
This function should take a struct udevice rather than pci_dev_t. Update it. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12dm: pci: video: Convert video and pci_rom to use DM PCI APISimon Glass
Adjust these files to use the driver-model PCI API instead of the legacy functions. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12dm: serial: Convert ns16550 driver to use driver model PCI APISimon Glass
Use the driver model version of the function to find the BAR. This updates the fdtdec function, of which ns16550 is the only user. The fdtdec_get_pci_bdf() function is dropped for several reasons: - with driver model we should use 'struct udevice *' rather than passing the device tree offset explicitly - there are no other users in the tree - the function parses for information which is already available in the PCI device structure (specifically struct pci_child_platdata which is available at dev_get_parent_platdata(dev) Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2016-01-12dm: pci: Add a function to read a PCI BARSimon Glass
Add a driver-model function for reading the PCI BAR from a device. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
generated by cgit (git 2.34.1) at 2025-01-10 18:40:44 +0000