| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds support for NANDs greater than 2 GB.
Patch is based on the MTD NAND driver in the kernel.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
|
|
In 16 bpp mode, the new IPEK01 board only requires swapping of D16 words
for D32 accesses due to the diffferent connecting to the GDC bus. This
patch introduces the configuration option VIDEO_FB_16BPP_WORD_SWAP,
which should be set for all board using the mb862xx in 16 bpp mode. For
the IPEK01, VIDEO_FB_16BPP_PIXEL_SWAP should not be set.
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
|
|
The new IPEK01 board can use the 32 bpp mode for the Lime graphics
controller. For this mode, video accelaration does not work. This patch
makes the accelaration configurable via CONFIG_VIDEO_MB862xx_ACCEL,
which is enabled for the lwmon5 and the socrates board for backward
compatibility.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
|
|
To avoid board-specific code accessing the mb862xx registers directly,
the public function mb862xx_probe() has been introduced. Furthermore,
the "Change of Clock Frequency" and "Set Memory I/F Mode" registers
are now defined by CONFIG_SYS_MB862xx_CCF and CONFIG_SYS_MB862xx__MMR,
respectively. The BSPs for the socrates and lwmon5 boards have been
adapted accordingly.
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
|
|
Signed-off-by: Valentin Yakovenkov <yakovenkov@niistt.ru>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
While we're here, improve the speed calculation a bit to match the HRM.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
The current transfer code relies on ctrlc() to abort transfers, but this
requires user interactivity. Naturalize the process with a timeout.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
Currently the CFI driver issues both AMD and Intel reset commands.
This is because the driver doesn't know yet which chips are connected.
This dual reset seems to cause problems with the M29W128G chips as
reported by Richard Retanubun. This patch now introduces a weak default
function for the CFI reset command, still with both resets. This can
be overridden by a board specific version if necessary.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Richard Retanubun <RichardRetanubun@ruggedcom.com>
|
|
Signed-off-by: Wolfgang Denk <wd@denx.de>
|
|
Add missing newline.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Luigi Mantellini <luigi.mantellini@idf-hit.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
|
|
Setup QE pin multiplexing for USB function, configure needed BCSRs
and add some fdt fixups.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Originally written by Jason Jin and Mingkai Hu for mpc8536.
When QorIQ based board is configured as a PCIe agent, then unlock/enable
inbound PCI configuration cycles and init a 4K inbound memory window;
so that a PCIe host can access the PCIe agents SDRAM at address 0x0
* Supported in fsl_pci_init_port() after adding pcie_ep as a param
* Revamped copyright in drivers/pci/fsl_pci_init.c
* Mods in 85xx based board specific pci init after this change
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Some of the new spi flash files were missing explicit license lines.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
|
|
|
|
Move the test up in the function to not hang on systems without ethernet.
Signed-off-by: Steve Sakoman <sakoman@gmail.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
|
|
fix the following compile warnings
warning: dereferencing type-punned pointer will break strict-aliasing rules
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
This patch re-formats the arm920t s3c24x0 nand driver in preparation for changes
to add support for the Embest SBC2440-II Board.
The changes are as follows:
- re-indent the code using Lindent
- make sure register layouts are defined using a C struct
- replace the upper-case typedef'ed C struct names with lower case
non-typedef'ed ones
- make sure registers are accessed using the proper accessor functions
- run checkpatch.pl and fix any error reports
It assumes the following patch has been applied first:
- [U-Boot][PATCH-ARM] CONFIG_SYS_HZ fix for ARM902T S3C24X0 Boards, 05/09/2009
- patches 1/4, 2/4 and 3/4 of this series
Tested on an Embest SBC2440-II Board with local u-boot patches as I don't have
any s3c2400 or s3c2410 boards but need this patch applying before I can submit
patches for the SBC2440-II Board. Also, temporarily modified sbc2410x, smdk2400,
smdk2410 and trab configs to use the mtd nand driver (which isn't used by any
board at the moment), ran MAKEALL for all ARM9 targets and no new warnings or
errors were found.
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This patch re-formats the arm920t s3c24x0 driver files, excluding the nand
driver, in preparation for changes to add support for the Embest SBC2440-II Board.
The changes are as follows:
- re-indent the code using Lindent
- make sure register layouts are defined using a C struct
- replace the upper-case typedef'ed C struct names with lower case
non-typedef'ed ones
- make sure registers are accessed using the proper accessor functions
- run checkpatch.pl and fix any error reports
It assumes the following patch has been applied first:
- [U-Boot][PATCH-ARM] CONFIG_SYS_HZ fix for ARM902T S3C24X0 Boards, 05/09/2009
- patches 1/4 and 2/4 of this series
Tested on an Embest SBC2440-II Board with local u-boot patches as I don't have
any s3c2400 or s3c2410 boards but need this patch applying before I can submit
patches for the SBC2440-II Board. Also, temporarily modified sbc2410x, smdk2400,
smdk2410 and trab configs to use the mtd nand driver (which isn't used by any
board at the moment), ran MAKEALL for all ARM9 targets and no new warnings or
errors were found.
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This patch includes the serial driver for s5pc1xx.
s5pc1xx uart driver needs own register setting and clock configuration.
So, need to special driver.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
This patch includes the onenand driver for s5pc100
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
|
|
Refactor the smc911x driver to allow for detecting when the chip is missing.
I.e. the detect_chip() function is called earlier and will abort gracefully
when the Chip ID read returns all 1's.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
|
|
Fix warning
Dereferencing type-punned pointer will break strict-aliasing rules
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
CC: Steve Sakoman <sakoman@gmail.com>
Acked-by: Tom Rix <Tom.Rix@windriver.com>
|
|
|
|
Forcing the tables into got2 caused extra relocation when using -mrelocatable.
This patch requires any board defining CONFIG_BIOSEMU to use -mrelocatable.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Acked-by: Jin Zhengxiong <Jason.Jin@freescale.com>
|
|
arbitrary number of mii buses.
This feature is useful when your board uses different mii buses for different
phys and all (or a part) of these buses are implemented via bit-banging mode.
The driver requires that the following macros should be defined into the board
configuration file:
CONFIG_BITBANGMII - Enable the miiphybb driver
CONFIG_BITBANGMII_MULTI - Enable the multi bus support
If the CONFIG_BITBANGMII_MULTI is not defined, the board's config file needs
to define at least the following macros:
MII_INIT - Generic code to enable the MII bus (optional)
MDIO_DECLARE - Declaration needed to access to the MDIO pin (optional)
MDIO_ACTIVE - Activate the MDIO pin as out pin
MDIO_TRISTATE - Activate the MDIO pin as input/tristate pin
MDIO_READ - Read the MDIO pin
MDIO(v) - Write v on the MDIO pin
MDC_DECLARE - Declaration needed to access to the MDC pin (optional)
MDC(v) - Write v on the MDC pin
The previous macros make the driver compatible with the previous version
(that didn't support the multi-bus).
When the CONFIG_BITBANGMII_MULTI is also defined, the board code needs to fill
the bb_miiphy_buses[] array with a record for each required bus and declare
the bb_miiphy_buses_num variable with the number of mii buses.
The record (struct bb_miiphy_bus) has the following fields/callbacks (see
miiphy.h for details):
char name[] - The symbolic name that must be equal to the MII bus
registered name
int (*init)() - Initialization function called at startup time (just
before the Ethernet initialization)
int (*mdio_active)() - Activate the MDIO pin as output
int (*mdio_tristate)() - Activate the MDIO pin as input/tristate pin
int (*set_mdio)() - Write the MDIO pin
int (*get_mdio)() - Read the MDIO pin
int (*set_mdc)() - Write the MDC pin
int (*delay)() - Delay function
void *priv - Private data used by board specific code
The board code will look like:
struct bb_miiphy_bus bb_miiphy_buses[] = {
{ .name = miibus#1, .init = b1_init, .mdio_active = b1_mdio_active, ... },
{ .name = miibus#2, .init = b2_init, .mdio_active = b2_mdio_active, ... },
...
int bb_miiphy_buses_num = sizeof(bb_miiphy_buses) /
sizeof(bb_miiphy_buses[0]);
Signed-off-by: Luigi 'Comio' Mantellini <luigi.mantellini@idf-hit.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
|
|
Modify all existing *.c files to use the new register names
as seen in the AMCC manuals.
Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
if link up detection code is disabled through config option, it gives build warning.
This patch fixes the same
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
All in-tree boards that use this controller have CONFIG_NET_MULTI
added
Also:
- changed CONFIG_DRIVER_SMC91111 to CONFIG_SMC91111
- cleaned up line lengths
- modified all boards that override weak function in this driver
- modified all eeprom standalone apps to work with new driver
- updated blackfin standalone EEPROM app after testing
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
|
|
following build warning was observed
mv88e61xx.c: In function ‘mv88e61xx_busychk’:
mv88e61xx.c:208: warning: dereferencing type-punned pointer will break strict-aliasing rules
This patch fixes the same
Patch tested for rd6281a board build
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
On 405EZ the RX-/TX-interrupts are coalesced into one IRQ bit in the
UIC. We need to acknowledge the RX-/TX-interrupts in the
SDR0_ICINTSTAT reg as well.
This problem was introduced with commit
d1631fe1 [ppc4xx: Consolidate PPC4xx UIC defines]
Signed-off-by: James Clough <james@rtetc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
|
|
Add #ifdefs where necessary to not perform relocation fixups. This
allows boards/architectures which support relocation to trim a decent
chunk of code.
Note that this patch doesn't add #ifdefs to architecture-specific code
which does not support relocation.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
|
|
PPC boards are the only users of the current FPGA code which is littered
with manual relocation fixups. Now that proper relocation is supported
for PPC boards, remove FPGA manual relocation.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
|
|
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
|
|
|
|
|
|
|
|
Don't include get_law_entry as part of the NAND_SPL build since the
code isnt used.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
I accidentally left v2 of "NAND: DaVinci:Adding 4 BIT ECC support"
applied when I pushed the tree last merge window, and missed these fixes
which were in v3 of that patch.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
|
|
__i2c_read always ends with a STOP condition thereby releasing
the bus. It is cleaner to do the STOP magic in i2c_read(), like
i2c_write() does. This may also help future multimaster systems which
wants to hold on to the bus until all transactions are finished.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
|
|
The latest AN2919 has changed the way FDR/DFSR should be calculated.
Update the driver according to spec. However, Condition 2
is not accounted for as it is not clear how to do so.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
|
|
Some boards need a higher DFSR value than the spec currently
recommends so give these boards the means to define there own.
For completeness, add CONFIG_FSL_I2C_CUSTOM_FDR too.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
|
|
After issuing a STOP one must wait until the STOP has completed
on the bus before doing something new to the controller.
Also add an extra read of SR as the manual mentions doing that
is a good idea.
Remove surplus write of CR just before a write, isn't required and
could potentially disturb the I2C bus.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
|
|
Headers should include headers containing prototypes and defines they
depend on, don't assume that they're included by somebody else.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
This will be needed for MPC8360E-MDS boards with rev. 2.1 CPUs.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
|
|
|
|
There are various locations that we have chip specific info:
* Makefile for which ddr code to build
* Added p4080 & p4040 to cpu_type_list and SVR list
* Added number of LAWs for p4080
* Set CONFIG_MAX_CPUS to 8 for p4080
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
On CoreNet based platforms the LAW address is split between an high &
low register and we no longer shift the address. Also, the target IDs
on CoreNet platforms have been completely re-assigned.
Additionally, added a new find_law() API to which LAW an address hits in.
This is need for the CoreNet style boot release code since it will need
to determine what the target ID should be set to for boot window
translation.
Finally, enamed LAWAR_EN to LAW_EN and moved to header so we can use
it elsewhere.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
