| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
|
|
In stead of user_buffer_size, transfer_size should be used to pass to
ahci_device_data_io(). transfer_size is the length that we want the
low level function to transfer each time.
If we use user_buffer_size which is the totally data length as parameter,
low level function will actually create many SGs to transfer as many data
as possible each time. That will produce many redundant data transfer.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Add support to configure EDP_RST GPIO and EDP_SLP GPIO,
if provided in parade DT node.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Add support to configure PWM_OUT(PWM output) GPIO and
BL_EN(backlight enable) GPIO, if provided in FIMD DT node.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
|
|
Now when all infrastructure in ARC is ready for it let's switch ARC UART
to driver model.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Simon Glass <sjg@chromium.org>
|
|
Being global variable with 0 value it falls into .bss area which we may
only use after relocation to RAM. And right afetr relocation we zero
.bss - effectively cleaing register address set for early console.
Now with pre-set value "regs" variable is no longer in .bss and this way
safely survives relocation.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
|
|
|
|
Add support for on-flash bad block table. This makes U-Boot handle an existing
BBT correctly.
Signed-off-by: David Dueck <davidcdueck@googlemail.com>
Reviewed-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
CC: Boris BREZILLON <boris.brezillon@free-electrons.com>
CC: Josh Wu <josh.wu@atmel.com>
CC: Andreas Bießmann <andreas.devel@googlemail.com>
CC: Scott Wood <scottwood@freescale.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
|
|
|
|
|
|
Testing showed, that commands like STATUS made the buffer dirty
when executed with NFC_SECSZ set to the page size. It looks
like the controller transfers bogus data when this register
is configured. When setting it to 0, the buffer does not get
altered while the status command still seems to work flawless.
Signed-off-by: Stefan Agner <stefan@agner.ch>
|
|
The driver tries to re-use the page buffer by storing the page
number of the current page in the buffer. The page is only read
if the requested page number is not currently in the buffer. When
a block is erased, the page number is marked as invalid if the
erased page equals the one currently in the cache. However, since
a erase block consists of multiple pages, also other page numbers
could be affected.
The commands to reproduce this issue (on a written page):
> nand dump 0x800
> nand erase 0x0 0x20000
> nand dump 0x800
The second nand dump command returns the data from the buffer,
while in fact the page is erased (0xff).
Avoid the hassle to calculate whether the page is affected or not,
but set the page buffer unconditionally to invalid instead.
Signed-off-by: Stefan Agner <stefan@agner.ch>
|
|
This command is only enabled by one board, complicates the NAND code,
and doesn't appear to have been functioning properly for several
years. If there are no bad blocks in the NAND region being written
nand_write_skip_bad() will take the shortcut of calling nand_write()
which bypasses the special yaffs handling. This causes invalid YAFFS
data to be written. See
http://lists.denx.de/pipermail/u-boot/2011-September/102830.html for
an example and a potential workaround.
U-Boot still retains the ability to mount and access YAFFS partitions
via CONFIG_YAFFS2.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
|
|
The CONFIG_MTD_NAND_VERIFY_WRITE has been removed from Linux for some
time and a more generic method of NAND verification now exists in U-Boot.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
|
|
Previously NAND writes were not verified and could fail silently. Add
a verification step after all writes to NAND.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
|
|
Add nand_verify() and nand_verify_page_oob(). nand_verify() verifies
NAND contents against an arbitrarily sized buffer using ECC while
nand_verify_page_oob() verifies a NAND page's contents and OOB.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
|
|
There is only one pio_word in this DMA transaction so data field must be 1.
Signed-off-by: Luca Ellero <luca.ellero@brickedbrain.com>
|
|
There is only one pio_word in this DMA transaction so data field must be 1.
Signed-off-by: Luca Ellero <luca.ellero@brickedbrain.com>
|
|
By specification the FIFO size would be in a range 2-256 bytes. From TX Level
prospective it means we can set threshold in the range 0-(FIFO size - 1) bytes.
Hence there are currently two issues:
a) FIFO size 2 bytes is actually skipped since TX Level is 1 bit and could be
either 0 or 1 byte;
b) FIFO size is incorrectly decreased by 1 which already done by meaning of
TX Level register.
Fixes: 501943696ea4 (spi: designware_spi: Fix detecting FIFO depth)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
|
|
Make local functions static and remove unneeded forward declarations.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
|
|
Don't assume slave is always the first member of struct cf_spi_slave.
Use container_of instead of casting first structure member.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
|
|
This patch enables QUAD read mode for qspi to improve the
read performace while loading the binaries from qspi.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
|
|
Don't assume slave is always the first member of struct ftssp010_spi.
Use to_ftssp010_spi() to ensure free correct address in spi_free_slave().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
|
|
It's done in spi_alloc_slave().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
|
|
The third parameter of container_of is the name of the member within the struct.
Current code only works if the parameter passed to to_cf_qspi_slave named slave.
Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
|
|
The usb0 / otg phy on sunxi boards has a bug where it wrongly detects a
high speed squelch on usb reset deassert when a lo speed device is plugged in.
The android kernel has a work around for this in the form of temporary
disabling the phy's squelch detection on reset deassert, this commit adds
the same workaround to the u-boot sunxi musb code, thereby fixing various usb
lo speed devices not working.
Tested with a (before non working) usb keyboard and a usb 2.4 GHz wireless
keyboard/mouse combo receiver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
|
|
Move arch/arm/include/asm/arch-bcm283x/*
-> arch/arm/mach-bcm283x/include/mach/*
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
|
|
|
|
|
|
board/sunxi/board.c tries to set ldo3 to 2.8v however drivers/power/axp209.c
contains an incorrect limit on ldo3 of 2.275v
The origin of the incorrect limit seems likely due to some inconsistencies
in the axp209 datasheet. ldo3 is described with different limits in
different sections. register 0x29 uses 7 bits for voltage configuration
while the 2.275v limit would apply if only 6 bits were used.
Probably this is a cut&paste error from register 0x23
The linux kernel driver has the correct limit and operation up to the 2.8v
required by my board has been physically verified with a multimeter.
Signed-off-by: Iain Paton <ipaton0@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Serial-uclass should be generically implemented without depending
a particular hardware. Fortunately, nothing in include/ns16550.h is
referenced from drivers/serial/serial-uclass.c, so remove this bogus
include.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
with WCR_WDW set, the watchdog won't trigger if we bootet linux and idle
around while the watchdog is not triggered. It seems the timer makes
progress very slowly if at all. I managed to remain 20minutes alive
while the timeout was set to 60secs. It reboots within 60secs if I start
a busyloop in userland (something like "while (1) { }").
While I don't see a reason why the WDT should not be running while the
CPU is in idle, I'm dropping this bit.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Stefano Babic <sbabic@denx.de>
|
|
Add a new driver for the Gigabit Ethernet MAC found on Intel Topcliff
Platform Controller Hub. Tested under 10/100 half/full duplex and 1000
full duplex modes using ping and tftpboot commands.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Some ethernet drivers use their own version of ethernet FCS length
macro which is really common. We define ETH_FCS_LEN in net.h and
replace those custom versions in various places.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Various files are needlessly rebuilt every time due to the version and
build time changing. As version.h is not actually needed, remove the
include.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Macpaul Lin <macpaul@andestech.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: York Sun <yorksun@freescale.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Philippe Reynes <tremyfr@yahoo.fr>
Cc: Eric Jarrige <eric.jarrige@armadeus.org>
Cc: "David Müller" <d.mueller@elsoft.ch>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Robert Baldyga <r.baldyga@samsung.com>
Cc: Torsten Koschorrek <koschorrek@synertronixx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Łukasz Majewski <l.majewski@samsung.com>
|
|
This allows printing the error message when VBUS is detected, as it would with
AXP VBUS detect.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
|
|
If the GBE bit is set, when do next time autonegotiation,
if the result is not 1000Mbps, it will fallback to 100Mbps
checking. So, we need to clear the GBE bit.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
|
|
|
|
The current implementation for baudrate calculation is incorrect.
This part from the formula:
"2 ^ (n + 1)" is not equivalent to (1 << n) but to (2 << n)!
This patch fixes this and moves this calculation to a function instead of using a macro.
This new function is taken from the Linux kernel.
This was detected and tested on the Marvell Armada A38x DB-88F6820-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
|
|
Change addresses to unsigned long to be compatible with 64-bit builds.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Heiko Schocher <hs@denx.de>
|
|
Change addresses to unsigned long to be compatible with 64-bit builds.
Regardless of fixing warnings, the device is still only 32-bit capable.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
|
|
Change addresses to unsigned long to be compatible with 64-bit builds.
Regardless of fixing warnings, the device is still only 32-bit capable.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
|
|
SDHCI_HOST_CONTROL is a byte-sized register, so don't write to it
as if it were a long, as that would result in clobbering the three
registers following.
Signed-off-by: Matt Reimer <mreimer@sdgsystems.com>
|
|
Properly mask SELBASECLK by using an actual mask rather than the
number of bits to shift in order to create the mask.
Signed-off-by: Matt Reimer <mreimer@sdgsystems.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Commit f022d36e8a4517b2a9d25ff2d75bd2459d0c68b1 introduces
error register offset.
Change the "char reserved3[59]" to "char reserved3[56]".
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
|
|
Panasonic's System LSI products, UniPhier SoC family, have been
transferred to Socionext Inc.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This enables the musb glue layer to use the AXP221's VBUS detection
function to check for VBUS. This fixes otg support on the A23 q8h
tablets.
Note that u-boot never calls musb_shutdown(), so once VBUS is enabled,
it is never disabled until the system is powered off, or the OS does
so. This can be used to our advantage to keep VBUS powered into the
OS, where support for AXP221 is not available yet.
Fixes: 52defe8f6570 ("sunxi: musb: Check Vbus-det before enabling otg port power")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Some of the AXP PMICs support VBUS detection, i.e. checking whether
VBUS power input is available and usable (supplied by an external
source). A few boards use this instead of a separate GPIO to detect
VBUS on USB OTG.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
For writing files, DFU implementation requires the file buffer
with the len at least of file size. For big files it requires
the same big buffer.
Previously the file buffer was allocated as a static variable,
so it was a part of U-Boot .bss section. For 32MiB len of buffer
we have 32MiB of additional space, required for this section.
The .bss needs to be cleared after the relocation.
This introduces an additional boot delay at every start, but usually
the dfu feature is not required at the standard boot, so the buffer
should be allocated only if required.
This patch removes the static allocation of this buffer,
and alloc it with memalign after first call of function:
- dfu_fill_entity_mmc()
and the buffer is freed on dfu_free_entity() call.
This was tested on Trats2.
A quick test with trace. Boot time from start to main_loop() entry:
- ~888ms - before this change (arch memset enabled for .bss clear)
- ~464ms - after this change
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
|
