summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2009-01-28Blackfin: overhaul i2c driverMike Frysinger
The current Blackfin i2c driver does not work properly with certain devices due to it breaking up transfers incorrectly. This is a rewrite of the driver and relocates it to the newer place in the source tree. Also remove duplicated I2C speed defines in Blackfin board configs and disable I2C slave address usage since it isn't implemented. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Blackfin: bfin_mac: update port muxingMike Frysinger
Adds support more Blackfin parts and fixes broken muxing for older ones. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-01-28Command usage cleanupPeter Tyser
Remove command name from all command "usage" fields and update common/command.c to display "name - usage" instead of just "usage". Also remove newlines from command usage fields. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-01-28Standardize command usage messages with cmd_usage()Peter Tyser
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-01-27soft_i2c.c add option for repeated start in i2c_read()Andrew Dyer
This patch adds a #define to optionally change the behaviour of i2c_read() in soft_i2c.c to send an I2C repeated start instead of a stop-start between sending the device address pointer write and reading back the data. The current behaviour is retained as the default. While most devices will work either way, I have a smart battery(*) that requires repeated start, and someone at some point found a device that required a stop-start. (*) http://www.inspired-energy.com/Standard_Products/NL2054/NL2054%20Rev1.0%20Data%20Sheet.pdf Signed-off-by: Andrew Dyer <adyer@righthandtech.com>
2009-01-27drivers/net/e1000.c: missing terminator for supported devicesStefan Althoefer
Signed-off-by: Stefan Althoefer <stefan.althoefer@web.de>
2009-01-26CFI: Add geometry reversal for STMicro M29W320ETRichard Retanubun
Added flash_fixup_stm to fix geometry reversal on STMicro M29W320ET flash chip. Modeled after flash_fixup_amd, this patch handles the geometry reversal or erase sectors that exist for ST Micro (now Numonyx) M29W320ET flash. Since I cannot test all STM's chips, the detection is implemented as narrow as possible for now. Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com> Signed-off-by: Stefan Roese <sr@denx.de>
2009-01-26CFI: increase performance of function find_sector()Jens Gehrlein
Tested on TQM5200S-BD with Samsung K8P2815UQB Signed-off-by: Jens Gehrlein <sew_s@tqs.de> Signed-off-by: Stefan Roese <sr@denx.de>
2009-01-26CFI: avoid redundant function call in single word programming modeJens Gehrlein
The function find_sector() doesn't need to be called twice in the case of AMD command set. Tested on TQM5200S-BD with Samsung K8P2815UQB. Signed-off-by: Jens Gehrlein <sew_s@tqs.de> Signed-off-by: Stefan Roese <sr@denx.de>
2009-01-24sh: sh_eth: Change new network APINobuhiro Iwamatsu
sh_eth used old network API. This patch changed new API. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-01-24net: smc911x: Make register read/write functions weakStefan Roese
This patch changes the reg_read/_write to smc911x_reg_read/_write and defines then as weak so that they can be overridden by board specific version. This will be used by the upcoming VCTH board support. Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-01-24powerpc: net: support for the SMSC LAN8700 PHYHeiko Schocher
Signed-off-by: Heiko Schocher <hs@denx.de> Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-01-24OMAP3: Add I2C supportDirk Behme
Add I2C support. Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-01-24OMAP3: Add MMC supportDirk Behme
Add MMC support. Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-01-24OMAP3: Add NAND supportDirk Behme
Add NAND support. Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Syed Mohammed Khasim <khasim@ti.com> Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
2009-01-24spi flash: fix crash due to spi flash miscommunicationBrad Bozarth
Higher spi flash layers expect to be given back a pointer that was malloced so that it can free the result, but the lower layers return a pointer that is in the middle of the malloced memory. Reorder the members of the lower spi structures so that things work out. Signed-off-by: Brad Bozarth <bflinux@yumbrad.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-01-24Add support for Maxim's DS4510 I2C devicePeter Tyser
Initial support for the DS4510, a CPU supervisor with integrated EEPROM, SRAM, and 4 programmable non-volatile GPIO pins. The CONFIG_DS4510 define enables support for the device while the CONFIG_CMD_DS4510 define enables the ds4510 command. The additional CONFIG_DS4510_INFO, CONFIG_DS4510_MEM, and CONFIG_DS4510_RST defines add additional sub-commands to the ds4510 command when defined. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2009-01-24serial: Rename driver vcth to vct to support other board variantsStefan Roese
Moved driver vcth.c to vct.c to better reflect the VCT board series. This driver is now used by the VCT platforms: vct_premium vct_platinum vct_platinumsvc Signed-off-by: Stefan Roese <sr@denx.de>
2009-01-24Added legacy flash ST Micro M29W040BNiklaus Giger
2009-01-23nand: fixup printf modifiers to match types usedMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-01-23NAND: rename NAND_MAX_CHIPS to CONFIG_SYS_NAND_MAX_CHIPSWolfgang Grandegger
This patch renames NAND_MAX_CHIPS to CONFIG_SYS_NAND_MAX_CHIPS and changes the default from 8 to 1 for the legacy and the new MTD NAND layer. This allows to remove all NAND_MAX_CHIPS definitions in the board config files because none of the boards use multi chip support (NAND_MAX_CHIPS > 1) so far. The bamboo and the DU440 define #define NAND_MAX_CHIPS CONFIG_SYS_MAX_NAND_DEVICE but that's bogus and did not work anyhow. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-01-23NAND: Enable nand lock, unlock featureNishanth Menon
Enable nand lock, unlock and status of lock feature. Not every device and platform requires this, hence, it is under define for CONFIG_CMD_NAND_LOCK_UNLOCK Nand unlock and status operate on block boundary instead of page boundary. Details in: http://www.micron.com/products/partdetail?part=MT29C2G24MAKLAJG-6%20IT Intial solution provided by Vikram Pandita <vikram.pandita@ti.com> Includes preliminary suggestions from Scott Wood Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-01-23NAND: move board_nand_init to nand.hMike Frysinger
Rather than putting the function prototype for board_nand_init() in the one place where it gets called, put it into nand.h so that every place that also defines it gets the prototype. Otherwise, errors can go silently unnoticed such as using the wrong return value (void rather than int) when defining the function. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-01-23OneNAND: Additional sync with 2.6.27Stefan Roese
- Add subpage write support - Add onenand_oob_64/32 ecclayout This has been missing and without it UBI has some incompatibilies issues with the current (>= 2.6.27) Linux kernel version. vid_hdr_offset is placed differently (2048 instead of 512) without this fix. Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Scott Wood <scottwood@freescale.com>
2009-01-23Add markbad functionKyungmin Park
Add missing markbad function If not, it's hang when it entered the mtd->mark_bad(). Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2009-01-23OneNAND: Save version_id in onenand_chip structStefan Roese
The version (ver_id) was not stored in the onenand_chip structure and because of this the continuous locking scheme could be enabled on some chips. Signed-off-by: Stefan Roese <sr@denx.de>
2009-01-23OneNAND: Fix compiler warningsStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de>
2009-01-23Sync with 2.6.27Kyungmin Park
Sync with OneNAND kernel codes Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2009-01-16sh: serial: use readx/writex accessorsJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2009-01-16sh: serial: coding style cleanupJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-12-30Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk
2008-12-19NAND FSL elbc: Use virt_to_phys to determine which bank is in useKumar Gala
The current code that determines which bank/chipselect is used for a given NAND instance only worked for 32-bit addresses and assumed a 1:1 mapping. This breaks in 36-bit physical configs. The proper way to handle this is to use the virt_to_phys() and BR_PHYS_ADDR() routinues to match the 34-bit lbc bus address with the the virtual address the NAND code uses. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Scott Wood <scottwood@freescale.com>
2008-12-19Add support for PCA953x I2C gpio devicesPeter Tyser
Initial support for NXP's 4 and 8 bit I2C gpio expanders (eg pca9537, pca9557, etc). The CONFIG_PCA953X define enables support for the devices while the CONFIG_CMD_PCA953X define enables the pca953x command. The CONFIG_CMD_PCA953X_INFO define enables an 'info' sub-command which provides summary information for the given pca953x device. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2008-12-19pci/fsl_pci_init: Enable inbound PCI config cyclesPeter Tyser
Add fsl_pci_config_unlock() function to enable a PCI/PCIe interface configured in agent/endpoint mode to respond to inbound PCI configuration cycles. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
2008-12-16NAND: Mark the BBT as scanned prior to calling scan_bbt.Scott Wood
Otherwise, recursion can occur if scan_bbt does not find a bad block table, and tries to write one, and the attempt to erase the BBT area causes a bad block check. Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-12-16Coding style cleanup, update CHANGELOG.Wolfgang Denk
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-12-16spi/stmicro: fix debug() display of cmdMike Frysinger
The stmicro_wait_ready() func tries to show the actual opcode that was sent to the device, but instead it displays the array pointer. Fix it to pull out the opcode from the start of the array. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2008-12-15i2c: merge all i2c_reg_read() and i2c_reg_write() into inline functionsTimur Tabi
All implementations of the functions i2c_reg_read() and i2c_reg_write() are identical. We can save space and simplify the code by converting these functions into inlines and putting them in i2c.h. Signed-off-by: Timur Tabi <timur@freescale.com> Acked-By: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-12-13Merge branch 'master' of git://git.denx.de/u-boot-shWolfgang Denk
2008-12-13Merge branch 'master' of git://git.denx.de/u-boot-ubiWolfgang Denk
2008-12-10sh: r2dplus fix register accessJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-12-10sh: Update SuperH serial driverNobuhiro Iwamatsu
The address of SCFSR register is wrong at SH7720/SH7721. This patch fix this. Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2008-12-10UBI: Return -ENOMEM upon failing mallocStefan Roese
Return with correct error code (-ENOMEM) from ubi_attach_mtd_dev() upon failing malloc(). Signed-off-by: Stefan Roese <sr@denx.de>
2008-12-10serial: Add vcth UART driverStefan Roese
This patch adds the UART driver for the upcoming VCTH board support. Signed-off-by: Stefan Roese <sr@denx.de>
2008-12-09Merge branch 'master' of /home/wd/git/u-boot/custodiansWolfgang Denk
2008-12-09drivers/fsl_pci_init: Fix compile warningKumar Gala
fsl_pci_init.c: In function 'fsl_pci_setup_inbound_windows': fsl_pci_init.c:122: warning: comparison is always true due to limited range of data type The check only makes sense if we are CONFIG_PHYS_64BIT Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-12-09usbtty/omap: update to current APIJean-Christophe PLAGNIOL-VILLARD
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: Remy Böhmer <linux@bohmer.net>
2008-12-09UBI: Enable re-initializing of the "ubi part" commandStefan Roese
With this patch now, the user can call "ubi part" multiple times to re-connect the UBI device to another MTD partition. Signed-off-by: Stefan Roese <sr@denx.de>
2008-12-09MTD: Fix problem based on non-working relocation (list head mtd_partitions)Stefan Roese
Don't use LIST_HEAD() but initialize the struct via INIT_LIST_HEAD() upon first call of add_mtd_partitions(). Otherwise this won't work on platforms where the relocation is broken (like MIPS or PPC). Signed-off-by: Stefan Roese <sr@denx.de>
2008-12-09Merge branch 'master' of git://git.denx.de/u-boot-netWolfgang Denk
generated by cgit (git 2.34.1) at 2024-12-26 10:28:38 +0000