summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2019-07-25net: tsec: Fix offset of MDIO registers for DM_ETHVladimir Oltean
By convention, the eTSEC MDIO controller nodes are defined in DT at 0x2d24000 and 0x2d50000, but actually U-Boot does not touch the interrupt portion of the register map (MDIO_IEVENTM, MDIO_IMASKM, MDIO_EMAPM). That leaves only the MDIO bus registers (MDIO_MIIMCFG, MDIO_MIIMCOM, MDIO_MIIMADD, MDIO_MIIMADD, MDIO_MIIMCON, MDIO_MIIMSTAT) which start at the 0x520 offset. So shift the DT-defined register map by the offset of MDIO_MIIMCFG when mapping the MDIO bus registers. Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-25net: tsec: Refactor the readout of the tbi-handle propertyVladimir Oltean
The point of this patch is to eliminate the use of the locally-defined "reg" variable (which interferes with next patch) and simplify the fallback to the default CONFIG_SYS_TBIPA_VALUE in case "tbi-handle" is missing. Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-25net/macb: increase RX buffer size for GEMRamon Fried
Macb Ethernet controller requires a RX buffer of 128 bytes. It is highly sub-optimal for Gigabit-capable GEM that is able to use a bigger DMA buffer. Change this constant and associated macros with data stored in the private structure. RX DMA buffer size has to be multiple of 64 bytes as indicated in DMA Configuration Register specification. Signed-off-by: Ramon Fried <rfried.dev@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-25net: macb: apply sane DMA configurationRamon Fried
DMA configuration was heavily dependent on the HW defaults, add function to properly set the required fields, including the new dma_burst_length. Signed-off-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Anup Patel <anup.patel@wdc.com> Tested-by: Anup Patel <anup.patel@wdc.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-25net: macb: add dma_burst_length configRamon Fried
GEM support higher DMA burst writes/reads than the default (4). add configuration structure with dma burst length so it could be applied later to DMA configuration. Signed-off-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Anup Patel <anup.patel@wdc.com> Tested-by: Anup Patel <anup.patel@wdc.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-25net: macb: add support for SGMII phy interfaceRamon Fried
This patch adds support for the sgmii phy interface, available only to DM users, dictated by current driver design. Signed-off-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Anup Patel <anup.patel@wdc.com> Tested-by: Anup Patel <anup.patel@wdc.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-25net: macb: use bit access macro from header fileRamon Fried
macb.h provides macros for reading/setting bitfields, in macb registers and descriptors. use that instead of redefining them in the source file. Signed-off-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Anup Patel <anup.patel@wdc.com> Tested-by: Anup Patel <anup.patel@wdc.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-25net: macb: add support for faster clk ratesRamon Fried
add support for clock rates higher than 2.4Mhz Signed-off-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Anup Patel <anup.patel@wdc.com> Tested-by: Anup Patel <anup.patel@wdc.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-25net: macb: sync header definitions as taken from LinuxRamon Fried
Few registers and bits were added by Cadence and they were not updated in the headers. Take the latest definitions as defined in Linux header (5.1) that also includes some comments about existing registers. One register was improperly named (UR), fix that. Signed-off-by: Ramon Fried <rfried.dev@gmail.com> Reviewed-by: Anup Patel <anup.patel@wdc.com> Tested-by: Anup Patel <anup.patel@wdc.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-25drivers: net: driver for MDIO muxes controlled over I2CAlex Marginean
This driver is used for MDIO muxes driven over I2C. This is currently used on Freescale LS1028A QDS board, on which the physical MDIO MUX is controlled by an on-board FPGA which in turn is configured through I2C. Signed-off-by: Alex Marginean <alexm.osslist@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-25net: designware: use 'phy_connect' instead of open codedSimon Goldschmidt
Using 'phy_connect' instead of 'phy_find_by_mask' and 'phy_connect_dev' both deduplicates code and adds support for 'fixed-link'. Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-25drivers: net: fsl_enetc: add support for SGMII 2500Alex Marginean
SGMII 2500 as supported on NXP SoCs requires AN to be disabled, handle this case in the enetc sgmii init code. Signed-off-by: Alex Marginean <alexm.osslist@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-25drivers: net: apply serdes configuration for ENETC Ethernet interfacesAlex Marginean
Ethernet interfaces using serial protocols go through the serdes block integrated in the SoC. This is accessed over dedicated internal MDIOs which are part of the Ethernet PCI functions. Set up serdes at _start, along with other protocol specific port/MAC configuration. MDIO code is shared with enetc_mdio, read/write functions are exported from fsl_enetc_mdio for this reason. Signed-off-by: Alex Marginean <alexm.osslist@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-25drivers: net: add NXP ENETC MDIO driverAlex Marginean
Adds a driver for the MDIO interface currently integrated in LS1028A SoC. This MDIO interface is shared by multiple ethernet interfaces and is presented as a stand-alone PCI function on the SoC ECAM. Ethernet has a functional dependency on MDIO, for simplicity there is a single config option for both. Signed-off-by: Alex Marginean <alexm.osslist@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-25drivers: net: add NXP ENETC ethernet driverAlex Marginean
Adds a driver for NXP ENETC ethernet controller currently integrated in LS1028A. ENETC is a fairly straight-forward BD ring device and interfaces are presented as PCI EPs on the SoC ECAM. Signed-off-by: Catalin Horghidan <catalin.horghidan@nxp.com> Signed-off-by: Alex Marginean <alexm.osslist@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-23Merge tag 'u-boot-stm32-20190723' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-stm - add rtc driver for stm32mp1 - add remoteproc driver for stm32mp1 - use kernel qspi compatible string for stm32
2019-07-23Merge tag 'rockchip-for-v2019.07-2' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip - rk3399 sdhci driver fixup - TPL BANNER fixup
2019-07-22rtc: Add rtc driver for stm32mp1Patrick Delaunay
Add support of STM32MP1 rtc driver. Enable it for basic and trusted configurations. Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
2019-07-22clk: stm32mp1: Add RTC clock entryPatrick Delaunay
Add RTCAPB and RTC clock support. Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-07-22spi: stm32_qspi: Remove "st, stm32-qspi" compatible stringPatrice Chotard
"st,stm32-qspi" is no more used, remove it. Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2019-07-22remoteproc: Introduce STM32 Cortex-M4 remoteproc driverFabien Dessenne
This patch introduces support of Cortex-M4 remote processor for STM32 MCU and MPU families. Signed-off-by: Loic Pallardy <loic.pallardy@st.com> Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
2019-07-22remoteproc: add elf file load supportFabien Dessenne
The current implementation supports only binary file load. Add helpers to support ELF32 format (sanity check, and load). Note that since an ELF32 image is built for the remote processor, the load function uses the device_to_virt ops to translate the addresses. Implement a basic translation for sandbox_testproc. Add related tests. Test result: => ut dm remoteproc_elf Test: dm_test_remoteproc_elf: remoteproc.c Test: dm_test_remoteproc_elf: remoteproc.c (flat tree) Failures: 0 Signed-off-by: Loic Pallardy <loic.pallardy@st.com> Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
2019-07-22dm: core: Introduce xxx_translate_dma_address()Fabien Dessenne
Add the following functions to translate DMA address to CPU address: - dev_translate_dma_address() - ofnode_translate_dma_address() - of_translate_dma_address() - fdt_translate_dma_address() These functions work the same way as xxx_translate_address(), with the difference that the translation relies on the "dma-ranges" property instead of the "ranges" property. Add related test. Test report: => ut dm fdt_translation Test: dm_test_fdt_translation: test-fdt.c Test: dm_test_fdt_translation: test-fdt.c (flat tree) Failures: 0 Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
2019-07-21Merge tag 'rockchip-for-v2019.07' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-rockchip - rk3399 lpddr4 support - rk3399-rock960 board support improvement - Eliminate pyelftools dependency by make_fit_atf.py - clean up rockchip dts to use -u-boot.dtsi - use ARM arch/generic timer instead of rk_timer - clean up Kconfig options for board support
2019-07-20rockchip: sdhci: Fix sdhci mmc driver probe abortKever Yang
This patch fix mmc driver abort caused by below patch: 3d296365e4 mmc: sdhci: Add support for sdhci-caps-mask After the patch sdhci_setup_cfg() access to host->mmc->dev, so we have to do init before make the call to the function() Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-07-20rockchip: video: rk3288_hdmi: Add missing call to dw_hdmi_enable()Niklas Schulze
The RK3288 HDMI driver's rk3288_hdmi_enable() currently lacks a call to dw_hdmi_enable(). Thus, the HDMI output never gets enabled. Signed-off-by: Niklas Schulze <me@jns.io> Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Kever Yang <Kever.yang@rock-chips.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-07-20rockchip: rk322x: sdram: use udelay instead of rockchip_udelayKever Yang
Use system api for udelay instead of vendor defined api, and rockchip_udelay() will be removed. Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-07-20ram: rk3399: Add lpddr4 set rate supportJagan Teki
Unlike rest of dram type chips, LPDDR4 initialization start with at board selected frequency (say 50MHz) and then it switches into 400MHz and 800MHz simultaneously to make the proper sequence work on each channel with associated training. The lpddr4 set rate sequnce will follow by setting lpddr4 - dq out - ca odt - MR3 - MR12 - MR14 registers sets in sequential order. Here is sameple log about LPDDR4-100 init sequence in Rockpro64: Channel 0: LPDDR4, 50MHz BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB Channel 1: LPDDR4, 50MHz BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB 256B stride channel 0 training pass channel 1 training pass change freq to 400 MHz 0, 1 channel 0 training pass channel 1 training pass change freq to 800 MHz 1, 0 This patch add support to this init sequence via lpddr4 set rate by taking sdram timing parameters from 400, 800 .inc files. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: YouMin Chen <cym@rock-chips.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> (Fix travis error, use one ret instead of ret[2] in set_ctrl) Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
2019-07-21ram: rk3399: Add set_rate sdram rk3399 opsJagan Teki
DDR set rate can be even required for lpddr4 and we need to keep the lpddr4 code to compile only for relevant boards which do support lpddr4. For this requirement, and for code readability handle data training via sdram_rk3399_ops with .set_rate and same will update in future while supporting lpddr4 code. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-21ram: rk3399: Add LPPDDR4-800 timings incJagan Teki
LPDDR4 initialization start with at board selected frequency and then it switches into 400MHz and 800MHz simultaneously to make the proper sequence work on each channel with associated training. So, add LPDDR4-800 timings inc file in driver area so-that these timings will take during LPDDR4 initialization phase. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: YouMin Chen <cym@rock-chips.com> Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-21ram: rk3399: Add LPPDDR4-400 timings incJagan Teki
LPDDR4 initialization start with at board selected frequency and then it switches into 400MHz and 800MHz simultaneously to make the proper sequence work on each channel with associated training. So, add LPDDR4-400 timings inc file in driver area so-that these timings will take during LPDDR4 initialization phase. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: YouMin Chen <cym@rock-chips.com> Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-21clk: rockchip: rk3399: Set 400MHz ddr clockJagan Teki
Add support for setting 400MHz ddr clock. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: YouMin Chen <cym@rock-chips.com> Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-21clk: rockchip: rk3399: Set 50MHz ddr clockJagan Teki
Add support for setting 50MHz ddr clock. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: YouMin Chen <cym@rock-chips.com> Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-21ram: rk3399: Add LPPDR4 mr detectionJagan Teki
Like data training in other sdram types, mr detection need to taken care for lpddr4 with looped rank and associated channel to make sure the proper configuration held. Once the mr detection successful for active and configured rank with channel number, the same can later reused during actual LPDDR4 initialization. So, add code to support for it. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: YouMin Chen <cym@rock-chips.com> Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-21ram: rk3399: Handle data training via opsJagan Teki
data training can be even required for lpddr4 and we need to keep the lpddr4 code to compile only for relevant boards which do support lpddr4. For this requirement, and for code readability handle data training via sdram_rk3399_ops and same will update in future while supporting lpddr4 code. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-21ram: rk3399: Simplify data training first argumentJagan Teki
data training is using chan_info as first argument with channel number as second argument instead of that use dram_info as first argument so-that we can get the chan_info at data training definition. This was the argument handling is meaningful, readable and it would help to add similar data training for lpddr4 in future. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-20ram: rk3399: Update lpddr4 vref_mode_acJagan Teki
Update vref_mode_ac for lpddr4 based on VDDQ/3/2=16.8% Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: YouMin Chen <cym@rock-chips.com> Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-20ram: rk3399: Update lpddr4 mode_sel based on io settingsJagan Teki
The mode_sel on lpddr4 value is depending on IO settings of rd_vref. Add support for it. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: YouMin Chen <cym@rock-chips.com>
2019-07-20ram: rk3399: Update lpddr4 vref based on io settingsJagan Teki
The vref_mode_dq, vref_value_dq on lpddr4 value is depending on IO settings of rd_vref. Add support for it. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: YouMin Chen <cym@rock-chips.com> Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-20ram: rk3399: Get lpddr4 tsel_rd_en from io settingsJagan Teki
For base.odt 1 the lpddr4 tsel_rd_en value is depending on IO settings of rd_odt_en. Add support for it. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: YouMin Chen <cym@rock-chips.com> Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-20ram: rk3399: Configure soc odt supportJagan Teki
CTL 145, 146, 159, 160 registers are used to configure soc odt on rk3399. These soc odt values are updated from CS0_MR22_VAL and CS1_MR22_VAL and for lpddr4 these values ORed with tsel_rd_select_n. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: YouMin Chen <cym@rock-chips.com>
2019-07-20ram: rk3399: Add tsel control clock driveJagan Teki
tsel contrl clock drives are required to configure PHY 929, 939 controls drive settings. Add support for these control clock for all dramtype sdrams. Thse control clock drives are configure via tsel_ckcs_select_p and tsel_ckcs_select_n variables. tsel_ckcs_select_n is PHY_DRV_ODT_34_3 value where as tsel_ckcs_select_p is retrived from IO settings for lpddr4 and rest uses PHY_DRV_ODT_34_3. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: YouMin Chen <cym@rock-chips.com> Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-20ram: sdram: Configure lpddr4 tsel rd, wr based on IO settingsJagan Teki
Now we have IO settings available for all supported sdram frequencies, so retrieve these IO settings and make used for LPDDR4 ds odt configuration. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: YouMin Chen <cym@rock-chips.com>
2019-07-20ram: rk3399: Add IO settingsJagan Teki
Add IO settings for dram ctl and phy. IO settings are useful for configuring ctl, phy odt, vref, mr5, mode select and other needed input output operations for lpddr4 or any other dramtype sdram. Right now, this patch added IO setting for all supported sdram frequencies. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: YouMin Chen <cym@rock-chips.com> Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-20ram: rk3399: Don't disable dfi dram clk for lpddr4, rank 1Jagan Teki
The hardware for LPDDR4 with - CLK0P/N connect to lower 16-bits - CLK1P/N connect to higher 16-bits and usually dfi dram clk is configured via CLK1P/N, so disabling dfi dram clk will disable the CLK1P/N as well. So, add patch to not to disable dfi dram clk for lpddr4, with rank 1. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: YouMin Chen <cym@rock-chips.com> Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-20ram: rk3399: Configure tsel write ca for lpddr4Jagan Teki
tsel write ca_p and ca_n values need to write on PHY 544, 672 and 800 to configure ds odt. Configure the same PHY register for lpddr4 would require a mask value of (300 << 8). Add support for it. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: YouMin Chen <cym@rock-chips.com> Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-20ram: rk3399: Map chipselect for lpddr4Jagan Teki
Assign desired cs_map values for lpddr4 during set memory map. Initial cs_map values is based on the sdram parameters, so the same will adjusted based dramtype as LPDDR4. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: YouMin Chen <cym@rock-chips.com>
2019-07-20ram: rk3399: Configure PHY RX_CM_INPUT for lpddr4Jagan Teki
Configure PHY RX_CM_INPUT for lpddr4 during phy IO config. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: YouMin Chen <cym@rock-chips.com> Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
2019-07-20ram: rk3399: Configure SLEWP_EN, SLEWN_EN for lpddr4Jagan Teki
Configure SLEWP_EN, SLEWN_EN for lpddr4 during phy IO config. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: YouMin Chen <cym@rock-chips.com>
2019-07-20ram: rk3399: Configure BOOSTP_EN, BOOSTN_EN for lpddr4Jagan Teki
Configure BOOSTP_EN, BOOSTN_EN for lpddr4 during phy IO config. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Signed-off-by: YouMin Chen <cym@rock-chips.com> Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
generated by cgit (git 2.34.1) at 2025-01-30 21:46:03 +0000