summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2006-11-03Added RGMII support to the TSECs and Marvell 881111 PhyNick Spence
Added a phy initialization to adjust the RGMII RX and TX timing Always set the R100 bit in 100 BaseT mode regardless of the TSEC mode Signed-off-by: Nick Spence <nick.spence@freescale.com>
2006-11-02This patch comes from Yuli's posted patch on 8/8/2006roy zang
titled "CFI Driver Little-Endian write Issue". http://sourceforge.net/mailarchive/message.php?msg_id=36311999 If that patch applied, please discard this one. Until now , I do not see his patch is applied. So please apply this one. Signed-off-by: Yuli Barcohen <yuli@arabellasw.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
2006-11-02Tsi108 on chip i2c support.roy zang
The i2c Interface provides a master-only, serial interface that can be used for initializing Tsi108/Tsi109 registers from an EEPROM after a device reset. Signed-off-by: Alexandre Bounine <alexandreb@tundra.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
2006-11-02Tsi108 on chip pci controller support.roy zang
If there is no pci card, the tsi108/109 pci configure read will cause a machine check exception to the processor. PCI error should also be cleared after the read. Signed-off-by: Alexandre Bounine <alexandreb@tundra.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
2006-11-02Tundra tsi108 on chip Ethernet controller support.roy zang
The following is a brief description of the Ethernet controller: The Tsi108/9 Ethernet Controller connects Switch Fabric to two independent Gigabit Ethernet ports,E0 and E1. It uses a single Management interface to manage the two physical connection devices (PHYs). Each Ethernet port has its own statistics monitor that tracks and reports key interface statistics. Each port supports a 256-entry hash table for address filtering. In addition, each port is bridged to the Switch Fabric through a 2-Kbyte transmit FIFO and a 4-Kbyte Receive FIFO. Each Ethernet port also has a pair of internal Ethernet DMA channels to support the transmit and receive data flows. The Ethernet DMA channels use descriptors set up in memory, the memory map of the device, and access via the Switch Fabric. The Ethernet Controller?s DMA arbiter handles arbitration for the Switch Fabric. The Controller also has a register businterface for register accesses and status monitor control. The PMD (Physical Media Device) interface operates in MII, GMII, or TBI modes. The MII mode is used for connecting with 10 or 100 Mbit/s PMDs. The GMII and TBI modes are used to connect with Gigabit PMDs. Internal data flows to and from the Ethernet Controller through the Switch Fabric. Each Ethernet port uses its transmit and receive DMA channels to manage data flows through buffer descriptors that are predefined by the system (the descriptors can exist anywhere in the system memory map). These descriptors are data structures that point to buffers filled with data ready to transmit over Ethernet, or they point to empty buffers ready to receive data from Ethernet. Signed-off-by: Alexandre Bounine <alexandreb@tundra.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
2006-11-02General code modification for mpc7448hpc2 board support.roy zang
1. Add 7447A and 7448 processor support. 2. Add the following flags. CFG_CONFIG_BUS_CLK : If the 74xx bus frequency can be configured dynamically (such as by switch on board), this flag should be set. CFG_EXCEPTION_AFTER_RELOCATE: If an exception occurs after the u-boot relocates to RAM, this flag should be set. CFG_SERIAL_HANG_IN_EXCEPTION: If the print out function will cause the system hang in exception, this flag should be set. There is a design issue for tsi108/109 pci configure read. When pci scan the slots, if there is no pci card, the tsi108/9 will cause a machine check exception for mpc7448 processor. Signed-off-by: Alexandre Bounine <alexandreb@tundra.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
2006-10-28[PATCH] NAND: Partition name support added to NAND subsystemStefan Roese
chpart, nboot and NAND subsystem related commands now accept also partition name to specify offset. Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Signed-off-by: Stefan Roese <sr@denx.de>
2006-10-26Fix TSEC driver (now for real): avoid crashes if PHY is not attachedBen Warren
to a TSEC (e.g. a switch is connected via RMII) or if the PHY is defective/incorrectly configured. Signed-off-by: Ben Warren <bwarren@qstreams.com>
2006-10-24Merge with /home/wd/git/u-boot/masterWolfgang Denk
2006-10-24Add common serial driver for Atmel AT32 and AT91 chipsWolfgang Denk
Patch by Haavard Skinnemoen, 06 Sep 2006 This is a first attempt at creating a common serial driver for Atmel chips. For now, it supports the AT32AP7000 AVR32 chip, but it should be possible to support AT91RM9200 and other ARM-based chips with some minor modifications. There's nothing fundamentally AVR32-specific in this driver, but it does use some features which are currently only defined for the AT32AP CPU port: * pm_get_clock_freq: Obtain the clock frequency of a given domain * gd->console_uart: A "struct device" containing information about register mappings, gpio resources and clocks associated with the UART device. For more information about these features, please see the "AT32AP CPU" patch.
2006-10-20Merge with http://www.jdl.com/software/u-boot-86xx.gitWolfgang Denk
2006-10-20Converted all 85xx boards to use a common FSL I2C driver.Jon Loeliger
Introduced COFIG_FSL_I2C to select the common FSL I2C driver. And removed hard i2c path from a few u-boot.lds scipts too. Minor whitespace cleanups along the way. Signed-off-by: Jon Loeliger <jdl@freescale.com>
2006-10-20Add board/cpu specific NAND chip select function to 440 NDFCStefan Roese
Based on idea and implementation from Jeff Mann Patch by Stefan Roese, 20 Oct 2006
2006-10-19Rewrite a series of goto statements as a sequences ofJon Loeliger
conditional expressions instead. Use consistent return code 0/-1 for good/bad indicators. Include one fewer file if the driver isn't used at all. Signed-off-by: Jon Loeliger <jdl@freescale.com>
2006-10-19Moved i2c driver out of cpu/mpc86xx/i2c.c into drivers/fsl_i2c.cJon Loeliger
in an effort to begin to unify the umpteen FSL I2C drivers that are all otherwise very similar. Signed-off-by: Jon Loeliger <jdl@freescale.com>
2006-10-12Merge branch 'master' of http://www.denx.de/git/u-bootJon Loeliger
2006-10-12Remove unneeded include files and local variable.Jon Loeliger
Signed-off-by: Jon Loeliger <jdl@freescale.com>
2006-10-12Fix spelling; minor code cleanup.Wolfgang Denk
2006-10-11Merge branch 'master' of http://www.denx.de/git/u-bootJon Loeliger
2006-10-10Merge branch 'master' of http://www.denx.de/git/u-bootJon Loeliger
2006-10-10Ran lindent and cleaned up whitespace issues.Jon Loeliger
Format for 80-columns too.
2006-10-10* Several improvements to the new NAND subsystem:Stefan Roese
- JFFS2 related commands implemented in mtd-utils style - Support for bad blocks - Bad block testing commands - NAND lock commands Please take a look at doc/README.nand for more details Patch by Guido Classen, 10 Oct 2006
2006-10-09Move "ar" flags to config.mk to allow for silent "make -s"Wolfgang Denk
Based on patch by Mike Frysinger, 20 Jun 2006
2006-10-09Coding style cleanupWolfgang Denk
2006-10-07CFG_NAND_QUIET_TEST added to not warn upon missing NAND deviceStefan Roese
Patch by Stefan Roese, 07 Oct 2006
2006-09-19Merge branch 'mpc85xx'Jon Loeliger
Conflicts: drivers/tsec.c
2006-09-19Add support for eTSEC 3 & 4 on 8548 CDSAndy Fleming
* Added support for using eTSEC 3 and eTSEC 4 on the 8548 CDS. This will only work on rev 1.3 boards (but doesn't break older boards) * Cleaned up some comments to reflect the expanded role of tsec in other systems
2006-09-19Merge branch 'master' of http://www.denx.de/git/u-bootJon Loeliger
Conflicts: board/stxxtc/Makefile
2006-09-04Merge with /home/m8/git/u-bootWolfgang Denk
2006-09-01Add support for a saving build objects in a separate directory.Marian Balakowicz
Modifications are based on the linux kernel approach and support two use cases: 1) Add O= to the make command line 'make O=/tmp/build all' 2) Set environement variable BUILD_DIR to point to the desired location 'export BUILD_DIR=/tmp/build' 'make' The second approach can also be used with a MAKEALL script 'export BUILD_DIR=/tmp/build' './MAKEALL' Command line 'O=' setting overrides BUILD_DIR environent variable. When none of the above methods is used the local build is performed and the object files are placed in the source directory.
2006-08-30Make the serial driver framework work with CONFIG_SERIAL_MULTI enabledWolfgang Denk
2006-08-23Merge branch 'mpc86xx'Jon Loeliger
2006-08-23Cleanup and lindent new AHCI driver.Jon Loeliger
2006-08-23Merge branch 'mpc86xx'Jon Loeliger
2006-08-23Add AHCI support to u-bootJin Zhengxiong
Add AHCI support in u-boot, enable the sata disk controllers which following the AHCI protocol. Signed-off-by:Jason Jin<jason.jin@freescale.com>
2006-08-22Merge branch 'master' of http://www.denx.de/git/u-bootJon Loeliger
2006-08-14Fix drivers/dm9000.c when configured in 32 bit mode.Wolfgang Denk
Patch by Eric Benard, 17 Nov 2005
2006-08-09Merge branch 'mpc85xx'Jon Loeliger
Conflicts: include/ft_build.h include/pci.h Resolved, though.
2006-08-09* Made sure the code which disables prefetch for PCI devices sets the size ↵Matthew McClintock
of the prefetch region to 0 Patch by Andy Fleming on 17-Mar-2006 Signed-off-by: Andy Fleming <afleming@freescale.com>
2006-08-09Merge branch 'wd'Jon Loeliger
2006-07-21Code cleanupWolfgang Denk
2006-07-21More code cleanupWolfgang Denk
2006-07-19Fix support for PS/2 keyboard on TQM85xx boardsWolfgang Denk
The PS/2 keyobard driver for the TQM85xx modules only supports the internal DUART of the MPC85xx CPU. Since the MPC8560 doesn't include a DUART, the TQM8560 modules can't be used with the PS/2 keyboard controller on the STK85xx board. The PS/2 keyboard driver should work with the modules TQM8540, TQM8541 and TQM8555, but it only has been tested on a TQM8540, yet. Make sure the PS/2 controller on the STK85xx is programmed. Jumper settings: X66 1-2, 9-10; X61 2-3 Patch by Martin Krause, 21 Jun 2006
2006-07-19Add support for TB5200 boardWolfgang Denk
The TB5200 ("Tinybox") is a small baseboard for the TQM5200 module integrated in a little aluminium case. Patch by Martin Krause, 8 Jun 2006 Some code cleanup
2006-07-10Major PCMCIA Cleanup to make code better readable and maintainable.Wolfgang Denk
Notes: - Board-dependend code for RPXLITE and RPXCLASSIC-based boards placed to the drivers/rpx_pmcia.c file to avoid duplication. Same for TQM8xx-based boards (drivers/tqm8xx_pmcia.c). - drivers/i82365.c has been split into two parts located at board/atc/ti113x.c and board/cpc45/pd67290.c (ATC and CPC45 are the only boards using CONFIG_82365). - Changes were tested for clean build and *very* *few* boards.
2006-06-30Merge: Add support for AMCC 440SPe CPU based eval board (Yucca).Marian Balakowicz
2006-06-30Add support for AMCC 440SPe CPU based eval board (Yucca).Marian Balakowicz
2006-06-28Merge branch 'mpc86xx'Jon Loeliger
2006-06-28Change Id to symbolic name for RTL8139Jin Zhengxiong
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
2006-06-27Merge branch 'mpc86xx'Jon Loeliger