summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2019-07-17mmc: am654_sdhci: Allow driver to probe without PDs specifiedAndreas Dannenberg
We would like to use the driver even without power domains being specified for cases such as during early boot when the required power domains have already gotten enabled by the SoC's boot ROM and such explicit initialization is not needed and possible. Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-07-17mmc: am654_sdhci: Add a platform specific set_control_reg() callbackFaiz Abbas
Add a platform specific set_control_reg() callback to help switch to UHS speed modes. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-07-17mmc: sdhci: Add support for HOST_CONTROL2 and setting UHS timingsFaiz Abbas
The HOST_CONTROL2 register is a part of SDHC v3.00 and not just specific to arasan/zynq controllers. Add the same to sdhci.h. Also create a common API to set UHS timings in HOST_CONTROL2. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-07-17mmc: am654_sdhci: Add Support for PHYFaiz Abbas
Add support in the driver for handling phy specific registers. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-07-17mmc: sdhci: Make set_ios_post() return intFaiz Abbas
Make set_ios_post() return int to faciliate error handling in platform drivers. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-07-17mmc: sdhci: Make sdhci_set_clock() non staticFaiz Abbas
The am654_sdhci driver needs to switch the clock off before disabling its phy dll and needs to re-enable the clock before enabling the phy again. Therefore, make the sdhci_set_clock() function accessible in the am654_sdhci driver. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-07-17mmc: sdhci: Add support for sdhci-caps-maskFaiz Abbas
Add Support for masking some bits in the capabilities register of a host controller. Also remove the redundant readl() into caps1. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-07-17regmap: Add API regmap_init_mem_index()Faiz Abbas
In device nodes with more than one entry in the reg property, it is sometimes useful to regmap only of the entries. Add an API regmap_init_mem_index() to facilitate this. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-07-17mmc: am654_sdhci: Remove quirksFaiz Abbas
The host controller works perfectly well without having to add any quirks. Remove them. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-07-17arm64: dts: k3: Sync sdhci0 node from kernel and change driver nameFaiz Abbas
Sync the sdhci0 node from kernel. This changes the compatible that is required to be there in the driver. Change the same for the SD card node which is not yet supported in kernel. This also syncs the main_pmx0 node as a side effect. Also change the name of the driver to match the compatible in kernel. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
2019-07-16Merge branch 'master' of https://gitlab.denx.de/u-boot/custodians/u-boot-sunxiTom Rini
- Beelink-x2 STB support (Marcus) - H6 DDR3, LPDDR3 changes (Andre, Jernej) - H6 pin controller, USB PHY (Andre)
2019-07-16sunxi: phy: Add USB PHY support for Allwinner H6Andre Przywara
The USB PHY used in the Allwinner H6 SoC has some pecularities (as usual), which require a small addition to the USB PHY driver: In this case the second PHY is PHY3, not PHY1, so we need to skip number 1 and 2 in the code. Just use the respective code from Linux for that. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> # Pine-H64 Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-07-16sunxi: clocks: Add H6 USB clock gates and resetsAndre Przywara
To enable USB support in U-Boot, add the required clock and reset gates to the H6 clock driver. Once enabled, the generic EHCI/OCHI drivers will pick them up from there automatically. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> # Pine-H64 Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-07-16sunxi: gpio: Enable support for H6 pin controllerAndre Przywara
The Allwinner H6 pin controller is not really special, at least not when it comes to normal GPIO operation. Add the H6 compatible strings to the list of recognised strings, to make GPIOs work for H6 boards. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> # Pine-H64 Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-07-16sunxi: move SUNXI_GPIO to KconfigAndre Przywara
Probably for no particular reason SUNXI_GPIO was still defined the "old way", in header files only. Introduce SUNXI_GPIO to the Kconfig file in drivers/gpio to remove another line from our dreadful config_whitelist.txt. Signed-off-by: Andre Przywara <andre.przywara@arm.com> Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> # Pine-H64 Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-07-15Merge branch 'master' of git://git.denx.de/u-boot-netTom Rini
2019-07-15net: macb: Add support for 1000-baseXRadu Pirea
Macb can be used with Xilinx PCS/PMA PHY in fpga which is a 1000-baseX phy(lpa 0x41e0). This patch adds checks for LPA_1000XFULL and LPA_1000XHALF bits. Signed-off-by: Radu Pirea <radu_nicolae.pirea@upb.ro> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-15net: macb: Fixed reading MII_LPA registerRadu Pirea
If macb is gem and is gigabit capable, lpa value is not read from the right register(MII_LPA) and is read from MII_STAT1000. This patch fixes reading of the lpa value. Signed-off-by: Radu Pirea <radu_nicolae.pirea@upb.ro> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-15net: ethernet: ti: Introduce am654 gigabit eth switch subsystem driverKeerthy
Add new driver for the TI AM65x SoC Gigabit Ethernet Switch subsystem (CPSW NUSS). It has two ports and provides Ethernet packet communication for the device and can be configured as an Ethernet switch. CPSW NUSS features: the Reduced Gigabit Media Independent Interface (RGMII), Reduced Media Independent Interface (RMII), and the Management Data Input/Output (MDIO) interface for physical layer device (PHY) management. The TI AM65x SoC has integrated two-port Gigabit Ethernet Switch subsystem into device MCU domain named MCU_CPSW0. One Ethernet port (port 1) with selectable RGMII and RMII interfaces and an internal Communications Port Programming Interface (CPPI) port (Host port 0). Host Port 0 CPPI Packet Streaming Interface interface supports 8 TX channels and on RX channels operating by TI am654 NAVSS Unified DMA Peripheral Root Complex (UDMA-P) controller. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Keerthy <j-keerthy@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-15driver: net: ti: cpsw-mdio: use phys_addr_t for mdio_base addrKeerthy
Use phys_addr_t for mdio_base address to avoid build warnings on arm64 and dra7. Cast it to uintprt_t before assigning to regs. Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Keerthy <j-keerthy@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-15net: phy: cortina: Use block layer to read from mmcYinbo Zhu
This patch is to use block layer to read from mmc in cortina Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-15net: mscc: refactor mscc_miimHoratiu Vultur
Because all MSCC SoC use the same MDIO bus, put the implementation in one common file(mscc_miim) and make all the other MSCC network drivers to use these functions. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-15test: dm: add MDIO testAlex Marginean
A very simple test for DM_MDIO, mimicks a register write/read through the sandbox bus to a dummy PHY. Signed-off-by: Alex Marginean <alexm.osslist@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-15net: introduce MDIO DM class for MDIO devicesAlex Marginean
Adds UCLASS_MDIO DM class supporting MDIO buses that are probed as stand-alone devices. Useful in particular for systems that support DM_ETH and have a stand-alone MDIO hardware block shared by multiple Ethernet interfaces. Signed-off-by: Alex Marginean <alexm.osslist@gmail.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-15net: mscc: serval: Remove delay when serdes is configuredHoratiu Vultur
When serdes configuration was written in hardware there was a delay of 100ms to be sure that configuration was written. But the delay is not needed because already the function serdes_write it is checking that the operation finished. Therefore remove the mdelay. This improves the speed of configuring the network driver. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-15net: phy: ti: Fix clock output DT propertyTrent Piepho
The code block reading the DT property for the clock output control was before the phy's DT node pointer was set, so it could never work. Move it after the node pointer is set. Also store the unsigned 32-bit property into an unsigned value, not a signed value, as the former will cause a problem if value overflows. For instance, if one were to add 0xffffffff as a code to mean the clock output should be turned off. Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Janine Hagemann <j.hagemann@phytec.de> Cc: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Trent Piepho <tpiepho@impinj.com> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-15net: phy: ti: Use default values for tx/rx delay and fifo sizeTrent Piepho
When not using DM_ETH, these PHY settings are programmed with default values hardcoded into the driver. When using DM_ETH, they should come from the device tree. However, if the device tree does not have the properties, the driver will silent use -1. Which is entirely out of range, programs nonsense into the PHY's registers, and does not work. Change this to use the same defaults as non-DM_ETH if the device tree is lacking the properties. As an alternative, the kernel driver for the phy will display an error message and fail if the device tree is lacking. Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Janine Hagemann <j.hagemann@phytec.de> Cc: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Trent Piepho <tpiepho@impinj.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2019-07-15Merge tag 'mmc-2019-7-15' of https://gitlab.denx.de/u-boot/custodians/u-boot-mmcTom Rini
- mmc spi driver model support - drop mmc_spi command - enhanced Strobe mmc HS400 support - minor mmc bug/fixes and optimization - omap hsmmc and mvbeu update - sdhci card detect support
2019-07-15mmc: fsl_esdhc_imx: enlarge mmc timeoutPeng Fan
Flash system partition with fastboot will earse the partition firstly The 600ms timeout will fail on some SD Card. Enlarge it to 5s to make it works for most of sdcard Cc: guoyin.chen <guoyin.chen@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-07-15mmc: fsl_esdhc_imx: add i.MX8QM compatiblePeng Fan
Add i.MX8QM compatible and soc data, the soc data is following Linux i.MX SDHC driver. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-07-15mmc: fsl_esdhc_imx: add HS400 Enhanced strobe supportPeng Fan
Implement set_enhanced_strobe hook for fsl_esdhc_imx, ,in esdhc_set_timing and esdhc_change_pinstate, also handle HS400_ES. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-07-15mmc: fsl_esdhc_imx: use mmc_of_parse to set host_capsPeng Fan
Use mmc_of_parse to set host_caps. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-07-15mmc: Parse no-1-8-v DT propertyPeng Fan
Parse no-1-8-v DT Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
2019-07-15mmc: Parse HS400 Enhanced strobe DT propertiesPeng Fan
Add HS400 Enhanced strobe properties parsing support to mmc_of_parse(). Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
2019-07-15mmc: support hs400 enhanced strobe modePeng Fan
eMMC 5.1+ supports HS400 Enhances Strobe mode without the need for tuning procedure. The flow is as following: - set HS_TIMIMG (Highspeed) - Host change freq to <= 52Mhz - set the bus width to Enhanced strobe and DDR8Bit(CMD6), EXT_CSD[183] = 0x86 instead of 0x80 - set HS_TIMING to 0x3 (HS400) - Host change freq to <= 200Mhz - Host select HS400 enhanced strobe complete Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-07-15mmc: fsl_esdhc_imx: fix config check issue when building in SPLYe Li
Should use CONFIG_IS_ENABLED not IS_ENABLED for clock and regulator drivers, CONFIG_IS_ENABLED will check the CONFIG_SPL_CLK and CONFIG_SPL_DM_REGULATOR when building SPL. Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-15mmc: mmc_spi: Re-write driver using DM frameworkBhargav Shah
This patch rewrites MMC SPI driver using U-Boot DM framework and get it's working on SiFive Unleashed board. Signed-off-by: Bhargav Shah <bhargavshah1988@gmail.com> Signed-off-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-15mmc: skip select_mode_and_width for MMC SPI hostAnup Patel
The MMC mode and width are fixed for MMC SPI host hence we skip sd_select_mode_and_width() and mmc_select_mode_and_width() for MMC SPI host. Signed-off-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2019-07-15mmc: retry a few times if a partition switch failedJean-Jacques Hiblot
This operation may fail. Retry it a few times before giving up and report a failure. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15mmc: do not change mode when accessing a boot partitionJean-Jacques Hiblot
Accessing the boot partition had been error prone with HS200 and HS400 and was disabled. The driver first switched to a lesser mode and then switched the partition access. It was mostly due to a bad handling of the switch and has been fixed, so let's remove this 'feature' Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15mmc: During a switch, poll on dat0 if available and check the final statusJean-Jacques Hiblot
The switch operation can sometimes make the bus unreliable, in that case the send_status parameter should be false to indicate not to poll using CMD13. If polling on dat0 is possible, we should use it to detect the end of the operation. At the end of the operation it is safe to use CMD13 to get the status of the card. It is important to do so because the operation may have failed. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15mmc: When switching partition, use the timeout specified in the ext_csdJean-Jacques Hiblot
The e-MMC spec allows the e-MMC to specify a timeout for the partition switch command. It can take up to 2550 ms. There is no lower limit to this value in the spec, but do as the the linux driver does and force it to be at least 300ms. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15mmc: use the generic timeout for cmd6 (SWITCH) provided in the ext_csdJean-Jacques Hiblot
Starting with rev 4.5, the eMMC can define a generic timeout for the SWITCH command. Following Linux Kernel code, the timeout also changed from 1000 -> 500 Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15mmc: if possible, poll the busy state using DAT0Jean-Jacques Hiblot
Using the DAT0 line as a rdy/busy line is an alternative to reading the status register of the card. It especially useful in situation where the bus is not in a good shape, like when modes are switched. This is also how the linux driver behaves. Note of warning: As per the specification, while polling on DAT0 the CLK must not turned off: "[...] Without a clock edge the Device (unless previously disconnected by a deselect command (CMD7)) will force the DAT0 line down, forever. [...]" Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15mmc: add mmc_poll_for_busy() and change the purpose of mmc_send_status()Jean-Jacques Hiblot
mmc_send_status() is currently used to poll the card until it is ready, not actually returning the status of the card. Make it return the status and add another function to poll the card. Also remove the 'extern' declaration in the mmc-private.h header to comply with the coding standard. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15mmc: omap_hsmmc: provide wait_dat0 even if UHS modes are not supportedJean-Jacques Hiblot
This function can also be used for eMMC devices. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15Revert "mmc: Add a new callback function to perform the 74 clocks cycle ↵Jean-Jacques Hiblot
sequence" This reverts commit 318a7a576bc49aa8b4207e694d3fbd48c663d6ac. The last and only user of this callback had been the omap_hsmmc driver. It is not used anymore. Removing the callback. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15mmc: omap_hsmmc: don't fill the send_init_stream callbackJean-Jacques Hiblot
This is not required. The MMC core sends CMD0 right after the initialization and it serves the same purpose. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15mmc: omap_hsmmc: reset FSM for DAT and CMD lines if needed before a new commandJean-Jacques Hiblot
It sometimes happen that the PSTATE register does not indicate that the bus is ready when it really is. This usually happens after a mode switch. In that case it makes sense to reset the FSM handling the CMD and DATA Also reset the FSMs if the STATE register cannot be cleared. This also sometimes happens after a mode switch. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
2019-07-15mmc: rpmb: fix response type of CMD25Akio Hirayama
The response type of CMD25 is R1 instead of R1b. Signed-off-by: Akio Hirayama <hirayama.akio@socionext.com> [masahiro: add log ] Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
generated by cgit (git 2.34.1) at 2025-01-05 23:56:10 +0000