summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2010-10-06sf: spansion: fixing erasing when sector size >64KiBMarc-André Hébert
The spansion_erase currently only works when the sector size is 64KB. cmd[1] should contain the higher 8 bit of the 24 bit address of the sector to be erased. Currently it is holding the sector index to be erased which happens to be the same thing when the sector size is 64KB. Signed-off-by: Marc-Andre Hebert <marc-andre.hebert@humanware.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-06sf: winbond: add support W25Q64 partsGraeme Smecher
Adds support for Winbond's W25Q64 SPI flash. These devices are used on (among others) Xilinx' SP601 and SP605 Spartan-6 evaluation boards. Tested with "sf" commands. Signed-off-by: Graeme Smecher <graeme.smecher@mail.mcgill.ca> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-05Merge branch 'master' of git://git.denx.de/u-boot-blackfinWolfgang Denk
2010-10-05Merge branch 'next' of git://git.denx.de/u-boot-videoWolfgang Denk
2010-10-02Blackfin: bfin_mac: convert from old style MMR macrosMike Frysinger
The old MMR defines are being scrubbed, so convert the driver to use the new standard helper macros. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: bfin_sdh: clean up send_cmdMike Frysinger
Simplify the command setup and status checking steps, and add a proper timeout to the status polling code to avoid possible infinite hangs. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-02Blackfin: bfin_spi: add optional DMA supportMike Frysinger
This moves the last piece from the old spi_flash driver to the new SPI framework -- optional DMA RX support. This typically cuts speeds by ~40% at the cost of additional ~300 bytes. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-09-28Merge branch 'next' of /home/wd/git/u-boot/nextWolfgang Denk
Conflicts: include/ppc4xx.h Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-09-27Fix "ubi part" cmd re-entrancyKarl Beldan
Commit 2ee951ba (UBI: Enable re-initializing of the "ubi part" command) reset mtd_devs in ubi_exit() but missed ubi_init()'s failure path. Signed-off-by: Karl Beldan <karl.beldan@gmail.com> Cc: Stefan Roese <sr@denx.de> Signed-off-by: Stefan Roese <sr@denx.de>
2010-09-25atmel_lcd: Allow contrast polarity to be either positive or negativeAlexander Stein
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
2010-09-23ppc4xx: Remove now unused CONFIG_UART1_CONSOLEStefan Roese
CONFIG_UART1_CONSOLE was a PPC4xx specific implementation and is now removed since the move from the 4xx UART driver to the common NS16550 UART driver. Let's remove all references to this define now. Signed-off-by: Stefan Roese <sr@denx.de>
2010-09-23ppc4xx: Big header cleanup, mostly PPC440 relatedStefan Roese
This patch starts a bit PPC4xx header cleanup. First patch mostly touches PPC440 files. A later patch will touch the PPC405 files as well. This cleanup is done by creating header files for all SoC versions and moving the SoC specific defines into these special headers. This way the common header ppc405.h and ppc440.h can be cleaned up finally. Signed-off-by: Stefan Roese <sr@denx.de>
2010-09-23ppc4xx: Move ppc4xx headers to powerpc include directoryStefan Roese
This patch moves some ppc4xx related headers from the common include directory (include/) to the powerpc specific one (arch/powerpc/include/asm/). This way to common include directory is not so cluttered with files. Signed-off-by: Stefan Roese <sr@denx.de>
2010-09-22Merge branch 'master' of git://git.denx.de/u-boot-blackfinWolfgang Denk
2010-09-21Blackfin: bfin_spi: use same gpio cs define as LinuxMike Frysinger
Linux uses an offset of 8 to switch from hardware cs to a gpio cs, so have u-boot use the same value. Also make sure it is public for boards to access. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-09-21video: cfb_console: add support for 4bpp bitmaps with GDF_32BIT_X888RGBTimur Tabi
Add support for 4bpp bitmaps, currently only for GDF_32BIT_X888RGB frame buffer format. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Anatolij Gustschin <agust@denx.de>
2010-09-21Merge branch 'next' of ../custodians into nextWolfgang Denk
2010-09-21Merge branch 'master' of /home/wd/git/u-boot/masterWolfgang Denk
2010-09-21Merge branch 'next' of git://git.denx.de/u-boot-usb into nextWolfgang Denk
2010-09-21Merge branch 'next' of ../custodians into nextWolfgang Denk
2010-09-20USB-CDC: Fix coding style issuesVitaly Kuzmichev
Fixes most of checkpatch warnings and errors in USB gadget stack. The most frequently encountered problems are: 1) "(foo*)", "foo * bar", "foo* bar" 2) C99 // comments 3) No spaces before/after/around '?', ':', '=', '==', ',', '&', '(' 4) Spaces before '[' 5) Spaces between function names and '(' 6) Block braces in wrong places 7) Spaces before tabs 8) Macros with complex values not enclosed in parenthesis 9) Multiline comments start just after /* Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
2010-09-20USB-CDC: called handle_interrupts inside usb_eth_sendStefano Babic
The patch removes an endless loop in the usb_eth_send if the tx_complete is not called before going in the loop. The driver interrupt routine is called allowing the driver to check if the TX is completed. Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-09-20USB-CDC: correct wrong alignment in ether.cStefano Babic
The buffer for the status request must be word aligned because it is accessed with 32 bit pointer in the eth_status_complete function. Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-09-20USB-CDC: change simple_strtol to simple_strtoulVitaly Kuzmichev
The patch is based on commit bb9496c6f7e853e5d4edd5397c9d45f1968d623c (done by Julia Lawall <julia@diku.dk>) from linux-2.6.git. Since num is unsigned, it would seem better to use simple_strtoul that simple_strtol. Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
2010-09-20USB-CDC: ethernet error path potential oops fixVitaly Kuzmichev
Fix potential oops on rare error path. The patch is based on commit e7b13ec9235b9fded90f826ceeb8c34548631351 (done by David Brownell <david-b@pacbell.net>) from linux-2.6.git. Description of the issue taken from linux kernel bugzilla: (https://bugzilla.kernel.org/show_bug.cgi?id=9594) The potential error can be tracked down as follows: (1) line 807: let the second conjunct on the "if" statment be false meaning "dev->status_ep" is null. This means the "if" evaluates to false. follow thru the code until... (2) line 808: usb_ep_disable(dev->status_ep) passes in a null argument, however "usb_ep_disable" cannot handle that: (from include/linux/usb/gadget.h) 191 static inline int 192 usb_ep_disable (struct usb_ep *ep) 193 { 194 return ep->ops->disable (ep); 195 } -- Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
2010-09-20USB-CDC: Correct stat_req initializationVitaly Kuzmichev
Fix possible oops on stat_req->buf initialization and fix ep0 and status_ep confusion (last one is just intended for stat_req keeping). Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com> Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-09-20USB-CDC: Replace 'strcpy' by 'strlcpy'Vitaly Kuzmichev
Replace 'strcpy' by more safe 'strlcpy' that is implemented in ether.c Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
2010-09-20USB-CDC: Correct freeing usb requestsVitaly Kuzmichev
Fix in_ep and out_ep confusion (rx_req was allocated from out_ep, not from in_ep) and add lost dev->req freeing. Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
2010-09-20USB-CDC: Use native debug printout macrosVitaly Kuzmichev
Replace Linux-like debug printout macros by native ones. Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com> Applied after removing dead code like '#define DEBUG/#undef DEBUG'
2010-09-20USB-CDC: Add lost 'qmult' definitionVitaly Kuzmichev
Add lost 'qmult' definition for High Speed devices and make it configurable through CONFIG_USB_ETH_QMULT. Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
2010-09-20USB-CDC: Restuct USB gadget MakefileVitaly Kuzmichev
Prohibit simultaneous usage of both old and new gadget stacks and allow UDC drivers to be dependent on CONFIG_USB_ETHER. Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
2010-09-20Integrate USB gadget layer and USB CDC driver layerRemy Bohmer
Derived from Linux kernel 2.6.27 Signed-off-by: Thomas Smits <ts.smits@gmail.com> Signed-off-by: Remy Bohmer <linux@bohmer.net>
2010-09-20usb: musb: stub out MUSB_TXCSR_MODE for Blackfin partsMike Frysinger
The MUSB_TXCSR_MODE register setting isn't supported on Blackfin musb parts, so stub it out to 0. This matches Linux behavior. Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-09-20cfi_flash: Remove uneccessary #ifdef CONFIG_SYS_MAX_FLASH_BANKS_DETECTStefan Roese
Now that the defines are moved to header files we don't need this conditional compilation any more. Remove it. Signed-off-by: Stefan Roese <sr@denx.de>
2010-09-20cfi_flash: Simplify dynamic flash bank number detectionStefan Roese
This patch simplifies the use of CONFIG_SYS_MAX_FLASH_BANKS_DETECT. By moving these optional variables and defines into the common code, board specific code is minimized. Currently only the following board use this feature: APC405, IDS8247, TQM834x And IDS8247 doesn't seem to really need this feature, since its not updating the bank number variable at all. So this patch removes the definition of CONFIG_SYS_MAX_FLASH_BANKS_DETECT from this board port. This new framework will be used by the upcoming lwmon5 update as well. Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Heiko Schocher <hs@denx.de> Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
2010-09-20cfi_flash: Add weak default for cfi_flash_bank_addr()Stefan Roese
cfi_flash_bank_addr(int bank_nr) returns the base addresses of the requested bank. Introducing this weak default enables boards to override this functions with a board specific version when required. This feature will be used in the lwmon5 board update, supporting runtime detection of 2 board revisions with different flash layouts. Signed-off-by: Stefan Roese <sr@denx.de>
2010-09-20cfi_flash: Simplify flash_get_info()Stefan Roese
This patch removes an unecessary check in the return statement. This is not needed, since "info" is initializes to NULL. And "info" will not be written to again, if the flash address is not found. Additionally "info" is not initialized to "0" but to "NULL". Signed-off-by: Stefan Roese <sr@denx.de>
2010-09-19Remove HMI10 board supportWolfgang Denk
Recent changes caused that the HMI10 board now is included in the boards built by MAKEALL, which revealed that compilation for this board has been broken for a long time: ps2ser.c: In function 'ps2ser_init': ps2ser.c:155: error: 'UART_LCR' undeclared (first use in this function) ps2ser.c:155: error: (Each undeclared identifier is reported only once ps2ser.c:155: error: for each function it appears in.) ps2ser.c:156: error: 'UART_DLL' undeclared (first use in this function) ps2ser.c:157: error: 'UART_DLM' undeclared (first use in this function) ps2ser.c:159: error: 'UART_IER' undeclared (first use in this function) ps2ser.c:160: error: 'UART_MCR' undeclared (first use in this function) ps2ser.c:161: error: 'UART_FCR' undeclared (first use in this function) ps2ser.c:162: error: 'UART_FCR_ENABLE_FIFO' undeclared (first use in this function) ps2ser.c:166: error: 'UART_LSR' undeclared (first use in this function) ps2ser.c: In function 'ps2ser_putc': ps2ser.c:198: error: 'UART_LSR' undeclared (first use in this function) ps2ser.c:200: error: 'UART_TX' undeclared (first use in this function) ps2ser.c: In function 'ps2ser_getc_hw': ps2ser.c:224: error: 'UART_LSR' undeclared (first use in this function) ps2ser.c:225: error: 'UART_RX' undeclared (first use in this function) ps2ser.c: In function 'ps2ser_interrupt': ps2ser.c:293: error: 'UART_IIR' undeclared (first use in this function) The board is orphaned, and AFAICT has reached EOL. Drop support for it. Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-09-19i2c, omap24xx: set bus_initialized only after relocation.Heiko Schocher
Portions of this work were supported by funding from the CE Linux Forum. Signed-off-by: Heiko Schocher <hs@denx.de>
2010-09-19mmc: fix compiler warningsWolfgang Denk
Commit d2bf29e3 caused a number of compiler warnings: mmc.c: In function 'mmc_bwrite': mmc.c:97: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'long unsigned int' mmc.c:97: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'lbaint_t' mmc.c: In function 'mmc_bread': mmc.c:229: warning: format '%x' expects type 'unsigned int', but argument 2 has type 'long unsigned int' mmc.c:229: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'lbaint_t' Fix these. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Lei Wen <leiwen@marvell.com>
2010-09-18mmc: add boundary check for mmc operationLei Wen
Signed-off-by: Lei Wen <leiwen@marvell.com>
2010-09-16video: cfb_console: fix definition and usage of CURSOR_xxx macrosTimur Tabi
The CURSOR_ON, CURSOR_OFF, and CURSOR_SET macros are defined incorrectly. If cursor support is disabled, then these macros are defined to nothing, but then they are used like this: if (console_col < CONSOLE_COLS) CURSOR_OFF console_row++; which was compiled like this: if (console_col < CONSOLE_COLS) console_row++; This is obviously not what was intended. Signed-off-by: Timur Tabi <timur@freescale.com> Acked-by: Detlev Zundel <dzu@denx.de>
2010-09-13nand/davinci: make sure ECC calculation has really startedWolfram Sang
Due to a register glitch (result code <4 might show up right after the start-calculation-bit was set), make sure the ECC has really started. See 1c3275b656045aff9a75bb2c9f3251af1043ebb3 in the kernel. Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Cc: Sandeep Paulraj <s-paulraj@ti.com>
2010-09-11usb: musb: set target address for non-multipoint devicesBryan Wu
Signed-off-by: Bryan Wu <bryan.wu@analog.com> Signed-off-by: Cliff Cai <cliff.cai@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-09-11usb: musb: setup TXCOUNT for Blackfin musbBryan Wu
The Blackfin implementation of musb has a TXCOUNT register that needs to be programmed when transmitting data. Signed-off-by: Bryan Wu <bryan.wu@analog.com> Signed-off-by: Cliff Cai <cliff.cai@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-09-10Prepare v2010.09-rc1Wolfgang Denk
Coding style cleanup. Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-09-09Merge branch 'master' of git://git.denx.de/u-boot-tiWolfgang Denk
2010-09-08mtd: nand: supress 'unknown NAND' warning if no nand is foundSteve Sakoman
This printk was added recently and results in ugly output on systems with no NAND: NAND: nand_get_flash_type: unknown NAND device: Manufacturer ID: 0x00, Chip ID: 0x00 0 MiB instead of: NAND: 0 MiB Signed-off-by: Steve Sakoman <steve@sakoman.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-09-08ARMV7: OMAP: add convenience function to set TWL4030 regulator voltagesSteve Sakoman
This patch adds a function to allow one to easily set the target voltage for the TWL4030 regulators. It also modifies the existing code to use this new function. Applicable definitions are moved out of the driver file and into the header file so that they are generally accessible Signed-off-by: Steve Sakoman <steve@sakoman.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-09-08Merge branch 'at91' of git://git.denx.de/u-boot-atmelWolfgang Denk
generated by cgit (git 2.34.1) at 2024-12-28 02:50:36 +0000