| Age | Commit message (Collapse) | Author |
|---|
|
A Coverity robot reported an integer handling issue
(OVERFLOW_BEFORE_WIDEN) in the potentially overflowing expression:
(mtd_div_by_ws(mtd->size, mtd) - mtd_div_by_ws(offs, mtd)) *
mtd_oobavail(mtd, ops)
While such overflow will certainly never happen due to the numbers
handled, it is cleaner to fix this operation anyway.
The problem is that all the maths include 32-bit quantities, while the
result is stored in an explicit 64-bit value.
As maxooblen will just be compared with a size_t, let's change the
type of the variable to a size_t. This will not fix anything but will
clarify a bit the situation. Then, do an explicit cast to fix Coverity
warning.
Addresses-Coverity-ID: 184180 ("Integer handling issues")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Add Macronix MX66U2G45F flash device description.
This is a 256 MiB part.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Vignesh R <vigneshr@ti.com>
[jagan: use 'g' instead of 'f' in flash name]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
|
|
Now the "spi-flash" compatible has been removed in the DTS files,
remove this compatible from sf_probe to finally use the Linux "jedec,spi-nor"
compatible.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
Add support for SPANSION s25fl064l
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Vignesh R <vigneshr@ti.com>
|
|
This patch sync's the U-Boot SPI NAND GigaDevice GD5F1GQ4UExxG support
with the latest Linux version (v5.0-rc3) plus the chip supported posted
on the MTD list. Only the currently in U-Boot available chip is
supported with this sync.
The changes for the GD5F1GQ4UExxG are:
- Name of NAND device changed to better reflect the real part
- OOB layout changed to only reserve 1 byte for BBT
- Use ECC caps 8bits/512bytes instead of 8bits/2048bytes
- Enhanced ecc_get_status() function to determine and report
a more fine grained bit error status
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
|
|
Use quad write if SPI_TX_QUAD flag is set.
Tested quad write on Stratix 10 SoC board (Micron
serial NOR flash, mt25qu02g)
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
|
|
Marvell's switch chips with integrated CPUs (collectively referred to as
MSYS) share common ancestry with the Armada SoCs. Some of the IP blocks
(e.g. xor) are located at different addresses and DFX server exists as a
separate target on the MBUS (on Armada-38x it's just part of the core
complex registers).
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
The kirkwood devices are compatible with this driver.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Fix the worng include and offset macros.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This fixes a compile error on kirkwood.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
With board_ahci_enable() implementation for Armada 38x in place we can
now enable 38x support in the ahci_mvebu driver.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
This patch adds DM support to the Armada XP SATA driver. This is needed
to enable CONFIG_BLK on this platform. It adds the SATA controller as
AHCI device, which is strictly speaking not correct, as the controller
is not AHCI compatible. But the U-Boot AHCI uclass interface enables
the usage of this DM driver and the creation of the corresponding BLK
devices.
This conversion is done to get rid of the compile warning:
Reviewed-by: Chris Packham <judge.packham@gmail.com>
===================== WARNING ======================
This board does not use CONFIG_DM_SCSI. Please update
the storage controller to use CONFIG_DM_SCSI before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
|
|
The generic wdt_start API expects to be called with the timeout in
milliseconds. Update the orion_wdt driver to accept a timeout in
milliseconds and use the clock rate specified in the dts to convert the
timeout to an appropriate value for the timer reload register.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
When run from the SPL the mvebu targets are using the hardware default
offset for the SoC peripherals. devfdt_get_addr_size_index() understands
how to deal with this via dm_get_translation_offset() so use this
instead of fdtdec_get_addr_size_auto_noparent().
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
The function dm_ofnode_pre_reloc should be used instead
of the function dm_fdt_pre_reloc and avoid duplicated code.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Prepare to remove dm_fdt_pre_reloc function.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Prepare to remove dm_fdt_pre_reloc
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
v2019.04-rc3 sandbox U-Boot fails to boot when compiled with
-fsanitize=address and linked against -lasan, reporting [1].
Git bisecting shows that the issue is contributed by v2019.01 commit
1678754f5e2c ("core: ofnode: Fix ofnode_get_addr_index function").
The root cause seems to be the mismatch between sizeof(u64) and
sizeof(fdt_size_t) on sandbox. Luckily, thanks to the fact that the
size argument of both of_get_address() and fdtdec_get_addr_size_fixed()
is optional, we can pass NULL in its place, avoiding the problem.
[1] Backtrace reported by ASAN (gcc 8.1.0):
$> ./u-boot -d arch/sandbox/dts/sandbox.dtb
[..]
Reviewed-by: Simon Glass <sjg@chromium.org>
=================================================================
==10998==ERROR: AddressSanitizer: stack-buffer-overflow on address 0x7ffcc2331140 at pc 0x0000004eeeb0 bp 0x7ffcc2330f80 sp 0x7ffcc2330f70
WRITE of size 8 at 0x7ffcc2331140 thread T0
#0 0x4eeeaf in of_get_address drivers/core/of_addr.c:154
#1 0x4f7441 in ofnode_get_addr_index drivers/core/ofnode.c:263
#2 0x5b2a78 in sb_eth_ofdata_to_platdata drivers/net/sandbox.c:422
#3 0x4dccd8 in device_probe drivers/core/device.c:407
#4 0x753170 in eth_initialize net/eth-uclass.c:428
#5 0x47d9bf in initr_net common/board_r.c:557
#6 0x6bcfa7 in initcall_run_list lib/initcall.c:30
#7 0x47e1fe in board_init_r common/board_r.c:859
#8 0x4060e5 in main arch/sandbox/cpu/start.c:356
#9 0x7fb8d135482f in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x2082f)
#10 0x40a3a8 in _start (/path/to/u-boot/u-boot+0x40a3a8)
Address 0x7ffcc2331140 is located in stack of thread T0 at offset 32 in frame
#0 0x4f72b8 in ofnode_get_addr_index drivers/core/ofnode.c:255
This frame has 3 object(s):
[32, 36) 'size' <== Memory access at offset 32 partially overflows this variable
[96, 100) 'flags'
[160, 168) 'node'
HINT: this may be a false positive if your program uses some custom stack unwind mechanism or swapcontext
(longjmp and C++ exceptions *are* supported)
SUMMARY: AddressSanitizer: stack-buffer-overflow drivers/core/of_addr.c:154 in of_get_address
Shadow bytes around the buggy address:
0x10001845e1d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x10001845e1e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x10001845e1f0: 00 00 00 00 00 00 00 00 00 00 00 00 f1 f1 f1 f1
0x10001845e200: 04 f2 f2 f2 f2 f2 f2 f2 04 f2 f2 f2 f2 f2 f2 f2
0x10001845e210: 04 f2 f2 f2 f3 f3 f3 f3 00 00 00 00 00 00 00 00
=>0x10001845e220: 00 00 00 00 f1 f1 f1 f1[04]f2 f2 f2 f2 f2 f2 f2
0x10001845e230: 04 f2 f2 f2 f2 f2 f2 f2 00 f2 f2 f2 f3 f3 f3 f3
0x10001845e240: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0x10001845e250: 00 00 00 00 f1 f1 f1 f1 00 00 f2 f2 f3 f3 f3 f3
0x10001845e260: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 f1 f1
0x10001845e270: f1 f1 00 f2 f2 f2 f3 f3 f3 f3 00 00 00 00 00 00
Shadow byte legend (one shadow byte represents 8 application bytes):
Addressable: 00
Partially addressable: 01 02 03 04 05 06 07
Heap left redzone: fa
Freed heap region: fd
Stack left redzone: f1
Stack mid redzone: f2
Stack right redzone: f3
Stack after return: f5
Stack use after scope: f8
Global redzone: f9
Global init order: f6
Poisoned by user: f7
Container overflow: fc
Array cookie: ac
Intra object redzone: bb
ASan internal: fe
Left alloca redzone: ca
Right alloca redzone: cb
==10998==ABORTING
'To' list:
git log --since=1year drivers/core/ofnode.c | grep "\-by: .*@" | \
sed 's/.*-by: //' | sort | uniq -c | sort -rn
10 Simon Glass <sjg@chromium.org>
3 Mario Six <mario.six@gdsys.cc>
2 Martin Fuzzey <mfuzzey@parkeon.com>
2 Marek Vasut <marek.vasut+renesas@gmail.com>
1 Tom Rini <trini@konsulko.com>
1 Masahiro Yamada <yamada.masahiro@socionext.com>
1 Keerthy <j-keerthy@ti.com>
1 Jens Wiklander <jens.wiklander@linaro.org>
1 Bin Meng <bmeng.cn@gmail.com>
Fixes: 1678754f5e2c ("core: ofnode: Fix ofnode_get_addr_index function")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
|
|
Use the new function syscon_regmap_lookup_by_phandle()
to simplify the code.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Change the function syscon_regmap_lookup_by_phandle()
introduced by commit 6c3af1f24e4b ("syscon: dm: Add a
new method to get a regmap from DTS") to have
Linux-compatible syscon API.
Same modification than commit e151a1c288bd ("syscon: add
Linux-compatible syscon API") solves issue when the node
identified by the phandle has several compatibles and is
already bound to a dedicated driver.
See Linux commit bdb0066df96e ("mfd: syscon: Decouple syscon
interface from platform devices").
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Some binding define child node gpio-controller without compatible property.
This patch avoid to bind the pinconfig uclass to these node.
For example, the binding for st,stm32-pinctrl
(./device-tree-bindings/pinctrl/st,stm32-pinctrl.txt) defines the GPIO
controller/bank node as sub-node of pincontrol (st,stm32f429-pinctrl)
but without compatible (as it is not mandatory).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
In case of system with several pin-controller device, probe the first
UCLASS_PINCTRL by seq number (defined by alias) to avoid race condition
with I2C PINCONTROL driver for GPIO expander (GPIO expander need I2C bus,
I2C driver need PINCONFIG).
Signed-off-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
This reverts commit 5ff776889212c080e3d1a33634ac904405ed6845.
As noted in the comment, the function pinctrl_decode_pin_config_dm()
only served as a temporary solution.
Since the function has no users anymore, we can remove it again.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
We can remove the pre reloc property in SPL and TPL device-tree:
- u-boot,dm-pre-reloc
- u-boot,dm-spl
- u-boot,dm-tpl
As only the needed node are kept by fdtgrep (1st pass).
The associated function (XXX_pre_reloc) are simple for SPL/TPL:
return always true.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
|
|
Merge drivers/soc/keystone/ into drivers/soc/ti/
and convert CONFIG_TI_KEYSTONE_SERDES into Kconfig.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
|
|
The UDMA-P is intended to perform similar (but significantly upgraded) functions
as the packet-oriented DMA used on previous SoC devices. The UDMA-P module
supports the transmission and reception of various packet types.
The UDMA-P also supports acting as both a UTC and UDMA-C for its internal
channels. Channels in the UDMA-P can be configured to be either Packet-Based or
Third-Party channels on a channel by channel basis.
The initial driver supports:
- MEM_TO_MEM (TR mode)
- DEV_TO_MEM (Packet mode)
- MEM_TO_DEV (Packet mode)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
|
|
The Ring Accelerator (RINGACC or RA) provides hardware acceleration to
enable straightforward passing of work between a producer and a consumer.
There is one RINGACC module per NAVSS on TI AM65x SoCs.
The RINGACC converts constant-address read and write accesses to equivalent
read or write accesses to a circular data structure in memory. The RINGACC
eliminates the need for each DMA controller which needs to access ring
elements from having to know the current state of the ring (base address,
current offset). The DMA controller performs a read or write access to a
specific address range (which maps to the source interface on the RINGACC)
and the RINGACC replaces the address for the transaction with a new address
which corresponds to the head or tail element of the ring (head for reads,
tail for writes). Since the RINGACC maintains the state, multiple DMA
controllers or channels are allowed to coherently share the same rings as
applicable. The RINGACC is able to place data which is destined towards
software into cached memory directly.
Supported ring modes:
- Ring Mode
- Messaging Mode
- Credentials Mode
- Queue Manager Mode
TI-SCI integration:
Texas Instrument's System Control Interface (TI-SCI) Message Protocol now
has control over Ringacc module resources management (RM) and Rings
configuration.
The Ringacc driver manages Rings allocation by itself now and requests
TI-SCI firmware to allocate and configure specific Rings only. It's done
this way because, Linux driver implements two stage Rings allocation and
configuration (allocate ring and configure ring) while TI-SCI Message
Protocol supports only one combined operation (allocate+configure).
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
|
|
Texas Instruments' System Control Interface (TI-SCI) Message Protocol
abstracts management of NAVSS resources, like PSI-L pairing and
unpairing, UDMAP tx/rx/flow configuration and Rings.
This patch adds support for requesting and configuring such resources
from TI-SCI firmware.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
|
|
|
|
- Various rmobile fixes
|
|
Write up to page size in each i2c transfer.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
Read the page size from DT when available.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
The PCA9543 is a 2-channel I2C switch.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher<hs@denx.de>
|
|
The chip_desc.enable field is used only for muxes, not for switches.
Document it and remove the unused values.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher<hs@denx.de>
|
|
The Kconfig help has not been updated while adding PCA9547 and PCA9646.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher<hs@denx.de>
|
|
The 'u-boot,i2c-transaction-bytes' device tree property provides
information regarding number of bytes transferred by a device in a
single transaction.
This change is necessary to avoid hanging devices after soft reset.
One notable example is communication with MC34708 device:
1. Reset when communicating with MC34708 via I2C.
2. The u-boot (after reboot -f) tries to setup the I2C and then calls
force_idle_bus. In the same time MC34708 still has some data to be sent
(as it transfers data in 24 bits chunks).
3. The force_idle_bus() is not able to make the bus idle as 8 SCL
clocks may be not enough to have the full transmission.
4. We end up with I2C inconsistency with MC34708.
This PMIC device requires 24+ SCL cycles to make finish any pending I2C
transmission.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
|
|
Periphs bank offset must be applied on all pins and
PMX bank to prevent issue in meson_pinconf_set call.
Without offset on pins when a call to pinconf is done
meson_gpio_calc_reg_and_bit return wrong offset.
To avoid breaking pmx function offset is needed in pmx bank structure too.
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
This patch add support for I2C controller in Meson-AXG SoC,
Due to the IP changes between I2C controller, we need to introduce
a compatible data to make the divider factor configurable.
backport from linux:
931b18e92cd0 ("2c: meson: add configurable divider factors")
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
|
|
Reset and initialize the PHY once in the probe() function rather than
doing it over and over again is start() function. This requires us to
keep the clock enabled while the driver is in use. This significantly
reduces the time between transfers as the PHY doesn't have to restart
autonegotiation between transfers, which takes forever.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
|
|
Synchronize R-Car Gen3 pin control tables with Linux 5.0,
commit 1c163f4c7b3f621efff9b28a47abb36f7378d783 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Synchronize R-Car Gen2 pin control tables with Linux 5.0,
commit 1c163f4c7b3f621efff9b28a47abb36f7378d783 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Linux 5.0, commit 1c163f4c7b3f621efff9b28a47abb36f7378d783,
has a TDSEL fix for R8A7790 H2 and R8A7794 E2 SoCs, implement
similar fix for U-Boot. The difference here is that the SoC
ES matching has to be implemented manually.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Synchronize R-Car Gen3 clock tables with Linux 5.0,
commit 1c163f4c7b3f621efff9b28a47abb36f7378d783 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Synchronize R-Car Gen2 clock tables with Linux 5.0,
commit 1c163f4c7b3f621efff9b28a47abb36f7378d783 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Add pin control tables for R8A77965 from Linux 5.0 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
Add clock tables for R8A77965 from Linux 5.0 , except for the
crit, R and Z clock, which are neither used nor supported by
the U-Boot clock framework yet.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
|
|
|
|
There exists code in drivers/common/common.c to read the dr_mode
from the device tree. This patch converts this driver to use that
function to initialize the driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
|
|
Drop the counter, it has no meaning other than being the order in which
the interface is found; the name assigned to the USB host controller
interface is a better indicator.
Example of the original output:
> USB0: USB EHCI 1.10
> scanning bus 0 for devices... 2 USB Device(s) found
> scanning usb for storage devices... 1 Storage Device(s) found
Patched output:
> Bus usb@ee080100: USB EHCI 1.10
> scanning bus usb@ee080100 for devices... 2 USB Device(s) found
> scanning usb for storage devices... 1 Storage Device(s) found
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
|
