summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2013-05-14T4/usb: move usb 2.0 utmi dual phy init code to cpu_init.cRoy Zang
This is what we have done for the UTMI PHY on P3041/P5020. Then the PHY initialization can be reused in kernel without “usb start” command. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-14net/phy: add VSC8574 supportShaohui Xie
The VSC8574 is a quad-port Gigabit Ethernet transceiver with four SerDes interfaces for quad-port dual media capability. This driver supports SGMII and QSGMII MAC mode. For now SGMII mode is tested. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-14net/fm: fixup ethernet for mEMACShengzhou Liu
- set proper compatible property name for mEMAC. - fixed ft_fixup_port for dual-role mEMAC, which will lead to MAC node disabled incorrectly. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-14powerpc/mpc85xx: Add T4160 SoCYork Sun
T4160 SoC is low power version of T4240. The T4160 combines eight dual threaded Power Architecture e6500 cores and two memory complexes (CoreNet platform cache and DDR3 memory controller) with the same high-performance datapath acceleration, networking, and peripheral bus interfaces. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-14T4/USB: Add USB 2.0 UTMI dual phy supportRoy Zang
T4240 internal UTMI phy is different comparing to previous UTMI PHY in P3041. This patch adds USB 2.0 UTMI Dual PHY new memory map and enable it for T4240. The phy timing is very sensitive and moving the phy enable code to cpu_init.c will not work. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-14Fman/t4240: some fix for 10G XAUIShaohui Xie
1. fix 10G mac offset by plus 8; 2. add second 10G port info for FM1 & FM2 when init ethernet info; 3. fix 10G lanes name to match lane protocol table; Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-14OMAP5: Enable USB Ethernet support with LAN9730Lubomir Popov
Added the LAN9730 to list of supported devices. This chip is used in the sEVM, uEVM and som5_evb. Tested on the som5_evb with dhcp and ping. Signed-off-by: Lubomir Popov <lpopov@mm-sol.com>
2013-05-13bfin: Move gpio support for bf54x and bf60x into the generic driver folder.Sonic Zhang
The gpio spec for bf54x and bf60x differ a lot from the old gpio driver for bf5xx. A lot of machine macros are used to accomodate both code in one gpio driver. This patch split the old gpio driver and move new gpio2 support to the generic gpio driver folder. - To enable gpio2 driver, macro CONFIG_ADI_GPIO2 should be defined in the board's config header file. - The gpio2 driver supports bf54x, bf60x and future ADI processors, while the older gpio driver supports bf50x, bf51x, bf52x, bf53x and bf561. - All blackfin specific gpio function names are replaced by the generic gpio APIs. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2013-05-13blackfin: The buf variable in bfin_mac.c is not used and produces warning,Marek Vasut
Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2013-05-13blackfin: Move blackfin serial driver out of blackfin arch folder.Sonic Zhang
- Move blackfin serial driver to the generic driver folder. - Move blackfin serial headers to blackfin arch head folder. - Update the include path to blackfin serial header in start up code. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2013-05-13blackfin: Move blackfin watchdog driver out of the blackfin arch folder.Sonic Zhang
- Enable hw_watchdog_init() in watchdog.h if CONFIG_HW_WATCHDOG is defined. - Move blackfin hw watchdog driver to the generic driver folder. - Call hw_watchdog_init() from blackfin board init code. - Reuse macro CONFIG_WATCHDOG_TIMEOUT_MSECS - Update README.watchdog accordingly Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2013-05-13bfin: discard invalid data and clear RXS in bf5xx spi driverScott Jiang
There may be dirty data in RDBR, so we should discard invalid data. This operation also clears RXS bit in STAT register. Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com> Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2013-05-13bfin: Remove spi dma function in bf5xx.Scott Jiang
BF5xx rx dma causes spi flash random read error. Accually spi controller has problems both on tx and rx dma. So remove spi dma support in u-boot. Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com> Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2013-05-12mmc: atmel_mci: add mmc card supportBo Shen
add mmc card support with atmel mci driver Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-05-12mmc: atmel_mci: using IP version for different settingBo Shen
Using IP version for different setting - Higher version supports 8bit mode - Higher version bus width setting is different Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-05-12spi: atmel_spi: using ip version to check whether has wdrbtBo Shen
Using IP version to check whether it has wdrbt bit in mode register Tested in at91sam9x5ek and at91sam9n12ek. Signed-off-by: Bo Shen <voice.shen@atmel.com> [fix warning about incompatible parameter] Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2013-05-11Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD
2013-05-11Revert wrong removal of nand_init and nand_deselectAlbert ARIBAUD
The manual resolution in commit ec7023db wrongly removed functions nand_init and nand_deselect from file drivers/mtd/nand/mxc_nand_spl.c. Revert this removal. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Acked-by: Stefano Babic <sbabic@denx.de>
2013-05-11Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD
Conflicts: drivers/mtd/nand/mxc_nand_spl.c include/configs/m28evk.h
2013-05-11Merge branch 'u-boot-pxa/master' into 'u-boot-arm/master'Albert ARIBAUD
2013-05-10palmas: use palmas_i2c_[read|write]_u8Nishanth Menon
commit 21144298 (power: twl6035: add palmas PMIC support) introduced twl6035_i2c_[read|write]_u8 Then, commit dd23e59d (omap5: pbias ldo9 turn on) introduced palmas_[read|write]_u8 for precisely the same access function. TWL6035 belongs to the palmas family, so instead of having an twl6035 API, we could use an generic palmas API instead. To stay consistent with the function naming of twl4030,6030 accessors, we use palmas_i2c_[read|write]_u8 Cc: Balaji T K <balajitk@ti.com> Cc: Sricharan R <r.sricharan@ti.com> Reported-by: Ruchika Kharwar <ruchika@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com>
2013-05-10palmas: rename twl6035_mmc1_poweron_ldo with an palmas generic functionNishanth Menon
Since TPS659038/TWL6035/TWL6037 all belong to palmas family of TI PMICs, rename twl6035_mmc1_poweron_ldo by a more generic palmas_mmc1_poweron_ldo function. Signed-off-by: Nishanth Menon <nm@ti.com>
2013-05-10palmas: rename init_settings to an generic palmas initNishanth Menon
Since TPS659038/TWL6035/TWL6037 all belong to palmas family of TI PMICs, rename twl6035_init_settings with an more generic palmas_init_settings Signed-off-by: Nishanth Menon <nm@ti.com>
2013-05-10twl6035: rename to palmasNishanth Menon
TPS659038/TWL6035/TWL6037 all belong to palmas family of TI PMICs Rename twl6035 to palmas to allow reuse across multiple current and future platforms As part of this change, change the CONFIG_TWL6035_POWER to CONFIG_PALMAS_POWER and update usage of header file accordingly. Signed-off-by: Nishanth Menon <nm@ti.com>
2013-05-10twl6030: move twl6030 register access functions to common header fileNishanth Menon
twl6030_i2c_[read|write]_u8 can be used else where to access multi-function device such as twl6030, so move the register access functions to the common twl6030.h header file. Signed-off-by: Nishanth Menon <nm@ti.com>
2013-05-10twl6030: twl6030_i2c_[read|write]_u8 prototype consistentNishanth Menon
u-boot standard i2c register access prototype is i2c_read(addr, reg, 1, &buf, 1) i2c_reg_write(u8 addr, u8 reg, u8 val) twl6030_i2c_read_u8(u8 addr, u8 *val, u8 reg) twl6030_i2c_write_u8(u8 addr, u8 val, u8 reg) does not provide consistency, so switch the prototype to be consistent with rest of u-boot i2c operations: twl6030_i2c_read_u8(u8 addr, u8 reg, u8 *val) twl6030_i2c_write_u8(u8 addr, u8 reg, u8 val) Signed-off-by: Nishanth Menon <nm@ti.com>
2013-05-10twl4030: make twl4030_i2c_read_u8 prototype consistentNishanth Menon
u-boot standard i2c read prototype is i2c_read(addr, reg, 1, &buf, 1) twl4030_i2c_read_u8(u8 addr, u8 *val, u8 reg) does not provide consistency, so switch the prototype to be consistent with rest of u-boot i2c operations: twl4030_i2c_read_u8(u8 addr, u8 reg, u8 *val) Signed-off-by: Nishanth Menon <nm@ti.com>
2013-05-10twl4030: make twl4030_i2c_write_u8 prototype consistentNishanth Menon
u-boot standard i2c register write prototype is i2c_reg_write(u8 addr, u8 reg, u8 val) twl4030_i2c_write_u8(u8 addr, u8 val, u8 reg) does not provide consistency, so switch the prototype to be consistent with rest of u-boot i2c operations: twl4030_i2c_write_u8(u8 addr, u8 reg, u8 val) Signed-off-by: Nishanth Menon <nm@ti.com>
2013-05-10phy: add support for ET1011C physMatt Porter
Adds an ET1011C PHY driver which is derived from the Linux kernel PHY driver (drivers/net/phy/et1011c.c) from the v3.9-rc2 tag. Note that an errata workaround config option is implemented to allow for TX_CLK to be enabled even when gigabit mode is negotiated. This workaround is used on the PG1.0 TI814X EVM. Signed-off-by: Matt Porter <mporter@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-05-10cpsw: add support for TI814x slave_regs differencesMatt Porter
TI814x's version 1 CPSW has a different slave_regs layout. Add support for the differing registers. Signed-off-by: Matt Porter <mporter@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-05-09gpio: Add support for microblaze xilinx GPIOMichal Simek
Microblaze uses gpio which is connected to the system reset. Currently gpio subsystem wasn't used for it. Add gpio driver and change Microblaze reset logic to be done via gpio subsystem. There are various configurations which Microblaze can have that's why gpio_alloc/gpio_alloc_dual(for dual channel) function has been introduced and gpio can be allocated dynamically. Adding several gpios IP is also possible and supported. For listing gpio configuration please use "gpio status" command This patch also remove one compilation warning: microblaze-generic.c: In function 'do_reset': microblaze-generic.c:38:47: warning: operation on '*1073741824u' may be undefined [-Wsequence-point] Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2013-05-07Merge branch 'master' of git://www.denx.de/git/u-boot-mmcTom Rini
2013-05-06mmc: fsl_esdhc: Use calloc()Fabio Estevam
A malloc() followed by memset() can be simply replaced by calloc(). Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-06mmc: sdhci: return error when failed add_sdhci().Jaehoon Chung
If failed the add_host(), it is reasonable that return value of add_sdhci(). Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-06sdhci: Add sdhci support for spear devicesVipin Kumar
Signed-off-by: Vipin Kumar <vipin.kumar@st.com> Acked-by: Stefan Roese <sr@denx.de> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-06davinci, mmc: Added a delay reading ext CSD registerDavide Bonfanti
Without this additional delay, some eMMC don't negotiate properly bus width Tested on: - Toshiba THGBM2G8D8FBAIB - Toshiba THGBM4G4D1HBAR - Micron MTFC4GMVEA (the one giving the problem) - Hynix H26M64002BNR - SanDisk SDIN5E1-32G Signed-off-by: Davide Bonfanti <davide.bonfanti@bticino.it> Acked-by: Tom Rini <trini@ti.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-06mmc: Split device init to decouple OCR-polling delayChe-Liang Chiou
Most of time that MMC driver spends on initializing a device is polling OCR (operation conditions register). To decouple this polling loop, device init is split into two parts: The first part fires the OCR query command, and the second part polls the result. So the caller is now no longer bound to the OCR-polling delay; he may fire the query, go somewhere and then come back later for the result. To use this, call mmc_set_preinit() on any device which needs this. This can save significant amounts of time on boot (e.g. 200ms) by hiding the MMC init time behind other init. Signed-off-by: Che-Liang Chiou <clchiou@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-06arm: mxs: Add MXS LCDIF driverMarek Vasut
Add basic LCD driver for i.MX233 and i.MX28. This driver allows framebuffer console and framebuffer logo. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Anatolij Gustschin <agust@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Anatolij Gustschin <agust@denx.de>
2013-05-06cfb_console: flush FB cache at end of public functionsEric Nelson
Removed internal cache_flush operations and placed a flush of the entire frame-buffer at the end of each public function. Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com> Signed-off-by: Anatolij Gustschin <agust@denx.de>
2013-05-06fpga: Check device name against bitstream nameMichal Simek
Ensure that wrong bitstream won't be loaded to current device. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-05-06fpga: zynq: Add support for loading bitstreamMichal Simek
Devcfg device requires to load bitstream in binary format. But u-boot also has an option for loading bitstream in bit format. Let's handle both cases by zynqpl driver. Also add suport for loading partial bitstreams. The first driver version was done by: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-05-06fpga: Change the first parameter in fpga_loadbitstreamMichal Simek
All fpga functions use devnum as int. Only fpga_loadbitstream is using it as unsinged long dev. This patch synchronize it. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-05-06cmd: fpga: Move fpga_loadbitstream to fpga.cMichal Simek
In bitstream decoding you can directly check device which you want to load and in fpga.c are fpga_validate and fpga_dev_info functions which should be used for it. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-05-06fpga: Fix debug message compilation errorMichal Simek
CONFIG_FPGA in past was a bitfield where bits were use for vendor identification. This fix should be the part of this commit: "Improve configuration of FPGA subsystem" (sha1: 0133502e39ff89b67c26cb4015e0e7e8d9571184) Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-05-06fpga: Clean coding styleMichal Simek
No functional changes. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Tom Rini <trini@ti.com>
2013-05-06usb: common: Use a global definition for 'min3'Vivek Gautam
We can use a common global method for calculating minimum of 3 numbers. Put the same in 'common header' and let 'ehci' use it. Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com> Acked-by: Tom Rini <trini@ti.com>
2013-05-05USB: ohci-at91: make OHCI work on at91sam9g10 SoCBo Shen
The at91sam9g10 need to configure HCK0 to make OHCI work Signed-off-by: Bo Shen <voice.shen@atmel.com>
2013-05-05usb: Add new command to set USB 2.0 port test modesJulius Werner
This patch adds a new 'usb test' command, that will set a port to a USB 2.0 test mode (see USB 2.0 spec 7.1.20). It supports all five test modes on both downstream hub ports and ordinary device's upstream ports. In addition, it supports EHCI root hub ports. Signed-off-by: Julius Werner <jwerner@chromium.org>
2013-05-05mtd: nand: add driver for diskonchip g4 nand flashMike Dunn
This patch adds a driver for the diskonchip G4 nand flash device. It is based on the driver from the linux kernel. This also includes a separate SPL driver. A separate SPL driver is used because the device operates in a different mode (reliable mode) when loading a boot image, and also because the storage format of the boot image is different from normal data (pages are stored redundantly). The SPL driver basically mimics how a typical IPL reads data from the device. The special operating mode and storage format are used to compensate for the fact that the IPL does not contain the BCH ecc decoding algorithm (due to size constraints). Although the u-boot SPL *could* use ecc, it operates like an IPL for the sake of simplicity and uniformity, since the IPL and SPL share the task of loading the u-boot image. As a side benefit, the SPL driver is very small. [port from linux kernel 3.4 commit 570469f3bde7f71cc1ece07a18d54a05b6a8775d] Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
2013-05-05pxa27x_udc: remove call to unimplemented set_GPIO_mode()Mike Dunn
If CONFIG_USB_DEV_PULLUP_GPIO is defined, a link error occurs because the set_GPIO_mode() helper function is not implemented. This function doesn't do much except make the code a little more readable, so I just manually coded its equivalent and removed the prototype from the header file. It is invoked no where else in the code. While I was at it, I noticed that two other function prototypes in the same header file are also neither implemented nor invoked anywhere, so I removed them as well. Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
generated by cgit (git 2.34.1) at 2025-02-10 00:00:01 +0000