summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2016-08-17serial: sh: Add support R8A7795Hiroyuki Yokoyama
This can be used in the same way as other R-CAR serial setting. Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2016-08-17ARM: Rmobile: Rename CONFIG_RMOBILE to CONFIG_ARCH_RMOBILENobuhiro Iwamatsu
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
2016-07-08mmc: msm_sdhci: Set mmc->dev pointer in msm_sdc_probe()Mateusz Kulikowski
MMC core expects (now) valid mmc->dev pointer. During conversion in commit cffe5d86 not every driver was updated. This patch fixes crash while accessing MMC on boards using Qualcomm SDHCI controller. Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com> Acked-by: Simon Glass <sjg@chromium.org>
2016-07-06Merge branch 'master' of git://git.denx.de/u-boot-tegraTom Rini
2016-07-06Merge branch 'master' of git://git.denx.de/u-boot-netTom Rini
2016-07-06net: rtl8169: Fix return value for rtl_send_commonOleksandr Tymoshenko
Return value of rtl_send_common propogates unmodified all the way up to eth_send and further to API consumer if CONFIG_API is enabled. Previously rtl_send_common returned number of bytes sent on success which was erroneouly detected as error condition by API consumers that checked for operation success by comparing return value with 0. Switch rtl_send_common to use common convention: return 0 on success and negative value for failure. Cc: Stephen Warren <swarren@nvidia.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Oleksandr Tymoshenko <gonzo@bluezbox.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-07-06driver: net: phylib: add support for aquantia AQR106/107 PHYMingkai Hu
This patch adds support for aquantia AQR106/107 PHY. Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-07-06net: designware: Make driver independent from DM_GPIO againAlexey Brodkin
Commit 90b7fc924adf "net: designware: support phy reset device-tree bindings" made DW GMAC driver dependent on DM_GPIO by unconditional usage of purely DM_GPIO stuff like: * dm_gpio_XXX() * gpio_request_by_name() But since that driver as of today might be easily used without DM_GPIO (that's the case for Synopsys AXS10x boards) we're shielding all DM_GPIO things by ifdefs. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Simon Glass <sjg@chromium.org> Cc: Beniamino Galvani <b.galvani@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Cc: Sonic Zhang <sonic.zhang@analog.com> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Marek Vasut <marex@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-07-05tegra: video: Always use write-through cache on LCDSimon Glass
This seems to give the best performance, so let's use it always. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-07-05video: tegra: Move to using simple-panel and pwm-backlightSimon Glass
We have standard drivers for panels and backlights which can do most of the work for us. Move the tegra20 LCD driver over to use those instead of custom code. This patch includes device tree changes for the nvidia boards. I have only been able to test seaboard. If this patch is applied, these boards will also need to be synced with the kernel, and updated to use display-timings: - colibri - medcom-wide - paz00 - tec Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-07-05pci: tegra: actually program REFCLK_CFG* on recent SoCsStephen Warren
On recent SoCs, tegra_pcie_phy_enable() isn't called; but instead tegra_pcie_enable_controller() calls tegra_xusb_phy_enable(). However, part of tegra_pcie_phy_enable() needs to happen in all cases. Move that code to tegra_pcie_port_enable() instead. For reference, NVIDIA's downstream Linux kernel performs this operation in tegra_pcie_enable_rp_features(), which is called immediately after tegra_pcie_port_enable(). Since that function doesn't exist in the U-Boot driver, we'll just add it to the tail of tegra_pcie_port_enable() instead. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-07-05pci: tegra: correctly program PADS_REFCLK registersStephen Warren
The value that should be programmed into the PADS_REFCLK register varies per SoC. Fix the Tegra PCIe driver to program the correct values. Future SoCs will require different values in cfg0/1, so the two values are stored separately in the per-SoC data structures. For reference, the values are all documented in NV bug 1771116 comment 20. The Tegra210 value doesn't match the current TRM, but I've filed a bug to get the TRM fixed. Earlier TRMs don't document the value this register should contain, but the ASIC team has validated all these values, except for the Tegra20 value which is simply left unchanged in this patch. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
2016-07-05rockchip: video: Lower hpd wait timeSjoerd Simons
Waiting 30 seconds for the hpd to go high seems a bit much, especially on headless boots. Lowering the timeout to 300ms. Sending as RFC because frankly i don't know what a sensible timeout is here, but 30 seconds is clearly not it :) Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk> Reviewed-by: Simon Glass <sjg@chromium.org> Dropped RFC tag: Signed-off-by: Simon Glass <sjg@chromium.org>
2016-07-01Merge branch 'master' of git://git.denx.de/u-boot-usbTom Rini
2016-07-01Merge branch 'master' of git://git.denx.de/u-boot-uniphierTom Rini
2016-07-01mmc: increase MMC SDHCI read status timeoutSteve Rae
Otherwise, ocassionally see errors like this: Flashing sparse image at offset 2078720 Flashing Sparse Image sdhci_send_command: Timeout for status update! mmc fail to send stop cmd write_sparse_image: Write failed, block #2181088 [0] This does not affect the actual writing speed, which is controlled by the default value: CONFIG_SDHCI_CMD_DEFAULT_TIMEOUT It only increases the retries when reading: SDHCI_INT_STATUS to avoid the timeout error. Signed-off-by: Steve Rae <steve.rae@raedomain.com> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Masahiro Yamada <yamada.masahiro@socionext.com> Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
2016-07-01driver: qspi: correct QSPI disable CS reset valuePraneeth Bajjuri
Correcting QSPI disable/unselect CS reset value. CTRL_CORE_CONTROL_IO_2: QSPI_MEMMAPPED_CS[10:8] This is not causing any issue, but its better to untouch the reserved bits. Praneeth Bajjuri <praneeth@ti.com> Signed-off-by: Ravi Babu <ravibabu@ti.com>
2016-07-02pinctrl: uniphier: add Ethernet pin-mux settingsMasahiro Yamada
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-07-02pinctrl: uniphier: avoid building unneeded pin-mux tables for SPLMasahiro Yamada
SPL does not use all of the devices, so we can save some memory footprint. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-07-02pinctrl: uniphier: support pin configuration for dedicated pinsMasahiro Yamada
PH1-LD4 and PH1-sLD8 SoCs have pins that support pin configuration (pin biasing, drive strength control), but not pin-muxing. Allow to fill the mux value table with -1 for those pins; pins with mux value -1 will be skipped in the pin-mux set function. The mux value type should be changed from "unsigned" to "int" in order to accommodate -1 as a special case. [ Linux commit: 363c90e743b50a432a91a211dd8b078d9df446e9 ] Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-07-02pinctrl: uniphier: split pinctrl driver for PH1-LD11 and PH1-LD20Masahiro Yamada
PH1-LD11 and PH1-LD20 have much pin controlling in common, so I added a single driver shared between them in the initial commit. However, the Ethernet pin-mux settings I am going to add are different with each other, and they may diverge more as the progress of development. Split it into two dedicated drivers. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-07-02pinctrl: uniphier: allow to have pinctrl node under syscon nodeMasahiro Yamada
Currently, the UniPhier pinctrl driver itself is a syscon, but it turned out much more reasonable to make it a child node of a syscon because our syscon node consists of a bunch of system configuration registers, not only pinctrl, but also phy, and misc registers. It is difficult to split the node. This commit allows to migrate to the new DT structure. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-06-30pinctrl: uniphier: remove unneeded pin group nand_cs1Masahiro Yamada
This SoC does not support NAND CS1. This place-holder is no longer necessary. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-06-30pinctrl: uniphier: fix NAND pin-mux setting for PH1-LD11/LD20Masahiro Yamada
My mistake in the initial support patch. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-06-30pinctrl: uniphier: remove wrong pin-mux functions for ProXstream2Masahiro Yamada
These are pin group names, not function names. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2016-06-28Merge git://git.denx.de/u-boot-fsl-qoriqTom Rini
2016-06-28armv8: fsl-layerscape: Append "A" in SoC name for ARM based SoCsPrabhakar Kushwaha
Freescale ARMv8 SoC name ends with "A" to represent ARM SoCs. like LS2080A, LS1043A, LS1012A. So append "A" to SoC names. Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-28mmc: fsl: introduce wp_enablePeng Fan
Introudce wp_enable. To check WPSPL, wp_enable needs to be set to 1 in board code. Take i.MX6UL for example, for some boards, they do not use WP singal, so they does not configure USDHC1_WP_SELECT_INPUT, and its default value is 0(GPIO1_IO02). However GPIO1_IO02 is muxed for i2c usage and SION bit set. So USDHC controller can always get wp signal and WPSPL shows write protect and blocks driver continuing. This is not what we want to see, so add wp_enable, and if set to 0, just omit the WPSPL checking and this does not effect normal working of usdhc controller. If wp-gpios is provided in dts, wp_enable is set to 1, otherwise 0. Signed-off-by: Peng Fan <van.freenix@gmail.com> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Cc: York Sun <york.sun@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Tested-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-28fsl_esdhc: Update clock enable bits for USDHCYe Li
The USDHC moves the 4 clock bits CARD_CLK_SOFT_EN, IPG_PERCLK_SOFT_EN, HCLK_SOFT_EN, and IPG_CLK_SOFT_EN from sysctl register to vendorspec register. The driver uses RSTA to replace the clock gate off operation. But this is not a good solution because: 1. when using RSTA, we should wait this bit to clear by itself. This is not implemeneted in the code. 2. After RSTA is set, it is recommended that the Host Driver reset the external card and reinitialize it. So in this patch, we change to use the vendorspec registers for these bits operation. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <van.freenix@gmail.com> Cc: York Sun <york.sun@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Tested-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-28mmc: fsl: reset to normal boot mode when eMMC fast bootPeng Fan
When booting in eMMC fast boot, MMC host does not exit from boot mode after bootrom loading image. So the first command 'CMD0' sent in uboot will pull down the CMD line to low and cause errors. This patch cleans the MMC boot register in "mmc_init" to put the MMC host back to normal mode. Also clear DLL_CTRL delay line settings at USDHC initialization to eliminate the pre-settings from boot rom. Signed-off-by: Peng Fan <van.freenix@gmail.com> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> Cc: York Sun <york.sun@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Tested-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-27fastboot: sparse: resync common/image-sparse.c (part 2)Steve Rae
- update fastboot_okay() and fastboot_fail() This file originally came from upstream code. While retaining the storage abstraction feature, this is the second set of the changes required to resync with the cmd_flash_mmc_sparse_img() in the file aboot.c from https://us.codeaurora.org/cgit/quic/la/kernel/lk/plain/app/aboot/aboot.c?h=LE.BR.1.2.1 Signed-off-by: Steve Rae <srae@broadcom.com>
2016-06-27fastboot: sparse: remove session-id logicSteve Rae
This "session-id" alogrithm is not required, and currently corrupts the stored image whenever more the one "session" is required. Signed-off-by: Steve Rae <srae@broadcom.com>
2016-06-27mmc: dw_mmc: fix the wrong AND operationJaehoon Chung
These condition checking are wrong. Original Author's intention might be "&" instead of "&&". It can know whether receive or transmit data request with BIT[4]/BIT[5] of RINTSTS register. Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2016-06-25ehci: mx7: fix otg id detectionPeng Fan
The USBNC_PHYCFG2_ACAENB bit should be cleared to enable the OTG ID detection, not set it. When the bit is set, the ACA Resistance Detection is enabled, which disables the OTG ID detection, because the internal pull up is off. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2016-06-25ehci: mx7: fix usbnc_regsPeng Fan
There is a 4 bytes hole between phy_cfg2 and phy_status, fix the usbnc_regs structure to include the hole. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com>
2016-06-25usb: fsl: Fix NULL terminating issue for usb controller name stringRajesh Bhagat
Fixes NULL terminating issue for usb controller name string by using sizeof operator. Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
2016-06-24clk: sandbox: don't check clk ID against 0Stephen Warren
clk->id is unsigned, so it can't be < 0. Remove the check for that. FWIW, this issue was introduced when the clock API converted e.g. clk_get_rate()'s clock ID parameter from an int to an unsigned long (with a struct clk), without removing this check. Fixes: 135aa9500264 ("clk: convert API to match reset/mailbox style") Reported-by: Coverity Scan Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org>
2016-06-24mtd: nand: Drop a blank line in nand_wait()Andre Renaud
This empty line should not be there. Remove it. Signed-off-by: Andre Renaud <andre@designa-electronics.com> Reviewed-by: Andreas Bießmann <andreas@biessmann.org> Signed-off-by: Simon Glass <sjg@chromium.org>
2016-06-21net: phy: marvell: Do not reset 88e1310 after autonegNathan Rossi
Commit a058052c "net: phy: do not read configuration register on reset", changes the behaviour of the phy_reset function such that the state of the BMCR register is not preserved during reset. Change the config function for the m88e1310 so that it does not do a reset after configuring auto-negotiation. Signed-off-by: Nathan Rossi <nathan@nathanrossi.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Stefan Roese <sr@denx.de> Acked-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Stefan Roese <sr@denx.de>
2016-06-21net: phy: micrel: add support for KSZ886x switches in MIIM modeAlexey Firago
This patch adds a phy driver for the Micrel KSZ886x switches. Similarly to the KSZ8895, SoC MAC is directly connected to the switch MAC on the switch CPU port, so the link to the switch is always up. KSZ886x switches can be used in the following configuration modes: - Unmanaged mode with config stored in external EEPROM - Managed mode over SPI - Managed mode over I2C - Managed mode over mdio/mdc (aka MIIM or SMI) This patch supports only unmanaged and MIIM modes. Based on Micrel KSZ886x driver from Linux kernel and Micrel KSZ8895 driver from U-Boot. Verified with the KSZ8863MLL. Signed-off-by: Alexey Firago <alexey_firago@mentor.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-06-21net: rtl8169: fix switching between adaptersStephen Warren
The rtl8169 driver uses a global variable to store the register address of the adapter being operated upon. This is updated to point at the correct adapter when sending or receiving a packet, or shutting down the adapter, but not when initializing the adapter. Consequently, switching between different adapters within the same U-Boot runtime does not work correctly since the driver programs the wrong registers during rtl8169_eth_start() -> rtl8169_common_start() -> rtl8169_hw_start(). Note that since rtl8169_eth_stop() does set the global variable, the second consecutive attempt to use the "new" adapter did work even before this patch, because each time network usage is shut down, the network core calls stop, which sets the variable so that the next start does actually initialize the hardware, and the adapter works. Equally, rtl8169_eth_probe() calls rtl_init() which sets the global, so if using only a single device, or if picking the "right" device (based on probe order) when multiple devices are present, ioaddr will already be set correctly from the get-go, so the issue does not occur. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-06-20Merge git://git.denx.de/u-boot-nand-flashTom Rini
2016-06-20mmc: add MMC_VERSION_5_1Stefan Wahren
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
2016-06-19mtd: nand: Patch remaining places where nand_to_mtd() should be usedBoris Brezillon
Some drivers are still directly accessing the chip->mtd field. Patch them to use nand_to_mtd() instead. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-06-19nand: nand torture: follow sync with linux v4.6Max Krummenacher
follow parameter name change (nand to mtd) to fix compiler error. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
2016-06-19spl: nand: sunxi: add support for NAND config auto-detectionBoris Brezillon
NAND chips are supposed to expose their capabilities through advanced mechanisms like READID, ONFI or JEDEC parameter tables. While those methods are appropriate for the bootloader itself, it's way to complicated and takes too much space to fit in the SPL. Replace those mechanisms by a dumb 'trial and error' mechanism. With this new approach we can get rid of the fixed config list that was used in the sunxi NAND SPL driver. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Hans de Goede <hdegoede@redhat.com>
2016-06-19spl: nand: sunxi: split 'load page' and 'read page' logicBoris Brezillon
Split the 'load page' and 'read page' logic in 2 different functions so we can later load the page and test different ECC configs without the penalty of reloading the same page in the NAND cache. We also move common setup to a dedicated function (nand_apply_config()) to avoid rewriting the same values in NFC registers each time we read a page. These new functions are passed a pointer to an nfc_config struct to limit the number of parameters. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Hans de Goede <hdegoede@redhat.com>
2016-06-19spl: nand: sunxi: rework status polling loopBoris Brezillon
check_value_xxx() helpers are using a 1ms delay between each test, which can be quite long for some operations (like a page read on an SLC NAND). Since we don't have anything to do but to poll this register, reduce the delay between each test to 1us. While we're at it, rename the max_number_of_retries parameters and the MAX_RETRIES macro into timeout_us and DEFAULT_TIMEOUT_US to reflect that we're actually waiting a given amount of time and not only a number of retries. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Hans de Goede <hdegoede@redhat.com>
2016-06-19spl: nand: sunxi: stop guessing the redundant u-boot offsetBoris Brezillon
Use CONFIG_SYS_NAND_U_BOOT_OFFS_REDUND value instead of trying to guess where the redundant u-boot image is based on simple (and most of the time erroneous) heuristics. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Hans de Goede <hdegoede@redhat.com> # Conflicts: # drivers/mtd/nand/sunxi_nand_spl.c
2016-06-19spl: nand: support redundant u-boot imageBoris Brezillon
On modern NAND it's more than recommended to have a backup copy of the u-boot binary to recover from corruption: bitflips are quite common on MLC NANDs, and the read-disturbance will corrupt your u-boot partitition more quickly than what you would see on an SLC NAND. Add an extra Kconfig option to specify the offset of the redundant u-boot image. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Hans de Goede <hdegoede@redhat.com> [scottwood: added ifdef to fix build break] Signed-off-by: Scott Wood <oss@buserror.net>