summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2019-10-25spi: Kconfig: Enable SPI_SUNXI for SUNXIJagan Teki
SPI_SUNXI driver is fully dm-aware and the Allwinner architecture kconfig would have logic to enable the DM_SPI. So, select default spi sunxi driver for sunxi architecture. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-25mtd: spi: Kconfig: Imply SPI_FLASH if DM_SPI_FLASHJagan Teki
DM_SPI_FLASH should require spi flash interface code for dm version, so imply SPI_FLASH core by default if any board enabled DM_SPI_FLASH. This overcome the explicit enablement of CONFIG_SPI_FLASH on respective boards when DM_SPI_FLASH being used. Acked-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-25dm: spi: Change cs_info op to return -EINVAL for invalid cs numBin Meng
We need distinguish the following two situations in various SPI APIs: - given chip select num is invalid - given chip select num is valid, but no device is attached Currently -ENODEV is returned for both cases. For the first case, it's more reasonable to return -EINVAL instead of -ENODEV for invalid chip select numbers. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> # SoPine Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-25dm: spi: Return 0 if driver does not implement ops->cs_infoBin Meng
If an SPI controller driver does not implement ops->cs_info, that probably means any chip select number could be valid, hence let's return 0 for spi_cs_info(). Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> # SoPine Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-25spi: Kconfig: Add help textJagan Teki
Add detailed help text for SPI support. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-25mtd: spi-nor: ids: Add is25wp256 chipJagan Teki
Add is25wp256, chip to spi-nor id table. Tested on SiFive FU540 board. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
2019-10-25mtd: spi: Kconfig: Update CONFIG_SPI_FLASHJagan Teki
1) CONFIG_SPI_FLASH is not just a legacy code, but it has common core code which handle both dm and non-dm spi flash code. So fix the info text to make it clear globally. 2) Since it's flash core it shouldn't depends on legacy SPI, so remove the 'depends on SPI' Cc: Vignesh R <vigneshr@ti.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-24Merge branch '2019-10-24-UFS-support'Tom Rini
- Add Universal Flash Storage (UFS) support
2019-10-24mtd: Add TI HyperBus Memory Controller driverVignesh Raghavendra
AM654/J721e has HyperBus Memory Controller that supports HyperFlash and HyperRAM devices. It provides a memory mapped interface to interact with these devices. Add a driver to support the same. Driver calibrates the controller, setups up for MMIO access and probes HyperFlash child node. Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Reviewed-by: Stefan Roese <sr@denx.de>
2019-10-24mtd: cfi_flash: Use CONFIG_SYS_MONITOR_BASE only when definedVignesh Raghavendra
Make use of CONFIG_SYS_MONITOR_BASE only when available to avoid build error when CONFIG_SYS_MONITOR_BASE is not defined. Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Reviewed-by: Stefan Roese <sr@denx.de>
2019-10-23ufs: Add glue layer driver for TI J721E devicesFaiz Abbas
Add glue layer driver for the controller present on TI's J721E devices. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-10-23ufs: Add Support for Cadence platform UFS driverFaiz Abbas
Add Support for the platform driver for the Cadence device present on TI's J721e device. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-10-23ufs: Add Initial Support for UFS subsystemFaiz Abbas
Add Support for UFS Host Controller Interface (UFSHCI) for communicating with Universal Flash Storage (UFS) devices. The steps to initialize the host controller interface are the following: - Initiate the Host Controller Initialization process by writing to the Host controller enable register. - Configure the Host Controller base address registers by allocating a host memory space and related data structures. - Unipro link startup procedure - Check for connected device - Configure UFS host controller to process requests Also register this host controller as a SCSI host controller. Taken from Linux Kernel v5.2 (drivers/scsi/ufs/ufshcd.c) and ported to U-boot. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-10-23scsi: Add dma direction member to command structureFaiz Abbas
Some SCSI devices like UFS use DMA for executing scsi commands and hence need to know the direction of transfer of the dma. Add a dma_dir element to the command structure to facilitate this. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-10-23scsi: Retry inquiry 3 times to overcome Unit Attention conditionFaiz Abbas
The UFS SCSI device LUNs are observed to return failure the first time a unit ready inquiry is sent and pass on the second try. Send this inquiry 3 times to make sure device is ready. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-10-23scsi: Add max_bytes_per_req to scsi_platdataFaiz Abbas
Add max_bytes_per_req to scsi_platdata to enable the host driver to limit the number of bytes that can be read/written per request. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
2019-10-23scsi: Simplify scsi_read()/_write()Faiz Abbas
With no non-DM driver using scsi_read()/_write() APIs, remove the legacy implementations. Signed-off-by: Faiz Abbas <faiz_abbas@ti.com> [trini: Reorder slightly and mark scsi_read/write behind BLK test to avoid warnings] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-21dm: pinctrl: fix for introduce PINCONF_RECURSIVE optionPatrick Delaunay
Correct the name of the define used CONFIG_IS_ENABLED which is not aligned with Kconfig name: CONFIG_$(SPL_)PINCONF_RECURSIVE. The recursive calls is conditional only for UCLASS_PINCONFIG "pinconfig" driver. It is always needed to call pinctrl_post_bind for UCLASS_PINCTRL "pinctrl", the test CONFIG_IS_ENABLED(PINCONF_RECURSIVE) need to be removed for this driver. This correct a regression introduced because the same patch is applied twice times in u-boot-dm branch: - commit e878b53a79d1 ("dm: pinctrl: introduce PINCONF_RECURSIVE option") - commit c20851b3d850 ("dm: pinctrl: introduce PINCONF_RECURSIVE option") Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-10-21pinctrl: Kconfig: remove duplicated nodesPatrick Delaunay
Remove the duplicated configs introduced when the same patch is applied twice times: - commit e878b53a79d1 ("dm: pinctrl: introduce PINCONF_RECURSIVE option") - commit c20851b3d850 ("dm: pinctrl: introduce PINCONF_RECURSIVE option") Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-10-18Merge tag 'u-boot-amlogic-20191018' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic - document alternative libretech-cc installation methods, including upstream TF-A and opensource tools - add HDMI/CVBS display support for Amlogic G12A SoCs and SEI510 board - add support for Amlogic A311D based Khadas VIM3 - add support for Amlogic S905X3 based SEI610 board, targeting Android support like SEI510
2019-10-18power: domain: add Amlogic Everything-Else power domain driverNeil Armstrong
Based on the 54ecb8f7028c ("Linux 5.4-rc1") Everything-Else power domain driver for Amlogic SoCs. This driver handles the VPU Power domain and other domains from the Everything-Else part of the SM1 and G12A SoCs. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-10-18clk: meson-sm1: add compatibleNeil Armstrong
The SM1 clock controller is almost identical to the G12A and so far the differences don't matter. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-10-18mmc: meson-gx: add support for mmc-pwrseq-emmcNeil Armstrong
Add support for mmc-pwrseq-emmc in the meson-gx mmc driver to support enabling the eMMC. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
2019-10-18video: meson: add compatible for Amlogic G12ANeil Armstrong
Finally add the Amlogic G12A SoC compatible for the VPU driver. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Anatolij Gustschin <agust@denx.de>
2019-10-18video: meson: sync with linux drm-misc treeNeil Armstrong
Synchronize the Amlogic Meson Video driver back with the latest DRM misc tree, adding G12A platform support, from the latest commit: 528a25d040bc ("drm: meson: use match data to detect vpu compatibility") The sync includes the following changes from Linux adapted to U-Boot: - Add support for VIC alternate timings - Switch PLL to 5.94GHz base for 297Mhz pixel clock - Add registers for G12A SoC - Add G12A Support for VPP setup - Add G12A Support for VIU setup - Add G12A support for OSD1 Plane - Add G12A support for plane handling in CRTC driver - Add G12A support for CVBS Encoder - Add G12A Video Clock setup - Add G12A support for the DW-HDMI Glue - fix G12A HDMI PLL settings for 4K60 1000/1001 variations - fix primary plane disabling - fix G12A primary plane disabling - mask value when writing bits relaxed - crtc: drv: vpp: viu: venc: use proper macros instead of magic constants - global clean-up - add macro used to enable HDMI PLL - venc: set the correct macrovision max amplitude value Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Anatolij Gustschin <agust@denx.de>
2019-10-18video: meson: remove power domain getNeil Armstrong
Remove getting and enabling the node power domain since it's now handled by the dm core directly. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Anatolij Gustschin <agust@denx.de>
2019-10-18clk: meson: g12a: add support for VPU/HDMI clocksNeil Armstrong
Add necessary clock support to set up clock for the VPU and HDMI support. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Anatolij Gustschin <agust@denx.de>
2019-10-18power: domain: meson-gx-pwrc: add G12A supportNeil Armstrong
Add Amlogic G12A support for the gx-pwrc driver, aligned on the Linux v5.2 driver. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Anatolij Gustschin <agust@denx.de>
2019-10-18gpio: sifive: add support for DM based gpio driver for FU540-SoCSagar Shrikant Kadam
This patch adds a DM based driver model for gpio controller present in FU540-C000 SoC on HiFive Unleashed A00 board. This SoC has one GPIO bank and 16 GPIO lines in total, out of which GPIO0 to GPIO9 and GPIO15 are routed to the J1 header on the board. This implementation is ported from linux based gpio driver submitted for review by Wesley W. Terpstra <wesley@sifive.com> and/or Atish Patra <atish.patra@wdc.com> (many thanks !!). The linux driver can be referred here [1] [1]: https://lkml.org/lkml/2018/10/9/1103 Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-10-17Merge tag 'for-v2020.01' of https://gitlab.denx.de/u-boot/custodians/u-boot-ubiTom Rini
ubi enhancements for 2020.01 - provide a way for skipping crc checks ported from linux, and add an U-Boot command to set this flag on already installed systems. - fix redundand environment management
2019-10-16ubi: Print skip_check in ubi_dump_vol_info()Stefan Roese
It might be interesting, if "skip_check" is set or not, so lets print this flag in ubi_dump_vol_info() as well. hs: fix typo in commit message Signed-off-by: Stefan Roese <sr@denx.de> Cc: Quentin Schulz <quentin.schulz@bootlin.com> Cc: Boris Brezillon <boris.brezillon@bootlin.com> Cc: Heiko Schocher <hs@denx.de> Reviewed-by: Heiko Schocher <hs@denx.de>
2019-10-16ubi: provide a way to skip CRC checksQuentin Schulz
Some users of static UBI volumes implement their own integrity check, thus making the volume CRC check done at open time useless. For instance, this is the case when one use the ubiblock + dm-verity + squashfs combination, where dm-verity already checks integrity of the block device but this time at the block granularity instead of verifying the whole volume. Skipping this test drastically improves the boot-time. Adapted to U-Boot by Stefan Roese. Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com> Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Heiko Schocher <hs@denx.de> Cc: Quentin Schulz <quentin.schulz@bootlin.com> Cc: Boris Brezillon <boris.brezillon@bootlin.com>
2019-10-15dm: Tidy up dump output when there are many devicesPatrick Delaunay
At present the 'Index' column of 'dm tree' assumes there is two digits, this patch increase it to 3 digits. It also aligns output of 'dm uclass', assuming the same 3 digits index. The boards with CONFIG_PINCTRL_FULL activated have one pinconfig by pin configuration, so they can have more than 100 devices pinconfig (for example with stm32mp157c-ev1 board we have 106 pinconfig node). Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-10-15dm: pinctrl: introduce PINCONF_RECURSIVE optionPatrick Delaunay
In the Linux pinctrl binding, the pin configuration nodes don't need to be direct children of the pin controller device (may be grandchildren for example). This behavior is managed with the pinconfig u-class which recursively bind all the sub-node of the pin controller. But for some binding (when pin configuration is only children of pin controller) that is not necessary. U-Boot can save memory and reduce the number of pinconf instance when this feature is deactivated (for arch stm32mp for example for SPL). This patch allows to control this feature with a new option CONFIG_PINCONF_RECURSIVE when it is possible for each individual pin controller device. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Simon Glass <sjg@chromium.org> Fixed CONFIG_IF_ENABLED() condition, added __maybe_unused: Signed-off-by: Simon Glass <sjg@chromium.org>
2019-10-15dm: core: device: switch off power domain after device removalAnatolij Gustschin
The power domain associated with a device is enabled when probing, but currently the domain remains enabled when the device is removed. Some boards started to disable power domains for selected devices via custom board_quiesce_devices(), but it doesn't work in many cases, i. e. because devices still can be accessed later in .remove() callback on behalf of dm_remove_devices_flags(). Utilize the DM core to power off the device power domain, but add a device flag to be able to selectively let the power domain enabled after device removal. This might be required for devices that must remain enabled when booting OS, i. e. serial console for debug output, etc. Signed-off-by: Anatolij Gustschin <agust@denx.de> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-10-15power: domain: Introduce dev_power_domain_offLokesh Vutla
Add dev_power_domain_off() api to disable all the power-domains corresponding to a device Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-10-15remoteproc: k3_arm64: Enable DM_FLAG_DEFAULT_PD_CTRL_OFFLokesh Vutla
Enable DM_FLAG_DEFAULT_PD_CTRL_OFF for arm64 remote core so that pd can be enabled after loading the image. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-10-15dm: core: Allow for not controlling the power-domain by DM frameworkLokesh Vutla
In some remoteproc cases, enabling the power domain of the core will start running the core. In such cases image should be loaded before enabling the power domain. But the current DM framework enables the power-domain by default during probe. This is causing the remotecore to start and crash as there is no valid image loaded. In order to avoid this introduce a DM flag that doesn't allow for enabling/disabling the power-domain by DM framework. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-10-15dm: pinctrl: Skip not associated gpio phandle and rise a warning messageMichael Trimarchi
Skip not associated gpio phandle let register the other gpios on a group. We need anyway to send out a warning to the user to fix their uboot-board.dtsi. Thhe handle id can be found inside the decompiled dtb dtc -I dtb -O dts -o devicetree.dts spl/u-boot-spl.dtb Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-10-15core: device: use dev_power_domain_onPeng Fan
When multiple power domains attached to a device, need power on them all, so use dev_power_domain_on to do that. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-15power: domain: add dev_power_domain_onPeng Fan
Add this new API to power on multiple domains attached to a device. Signed-off-by: Peng Fan <peng.fan@nxp.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Changed to static inline and added a condition into C file: Signed-off-by: Simon Glass <sjg@chromium.org>
2019-10-15dm: spi: Do not assume first SPI busThomas Fitzsimmons
When CONFIG_OF_PRIOR_STAGE is enabled, this workaround was needed before device_bind_common assigned request numbers sequentially in the absence of aliases. Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Simon Glass <sjg@chromium.org>
2019-10-15dm: device: Request next sequence numberThomas Fitzsimmons
For CONFIG_OF_PRIOR_STAGE, in the absence of a device tree alias for a given device, use the next request number for that type of device. This allows aliases to be used when they're available, while still allowing unaliased devices to be probed. Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org> Cc: Bin Meng <bmeng.cn@gmail.com> Cc: Simon Glass <sjg@chromium.org>
2019-10-15tpm2: Don't assume active low reset valueKayla Theil
The reset function sets the pin to 0 then 1 but if the pin is marked ACTIVE_LOW in the DT it gets inverted and leaves the TPM in reset. Let the gpio driver take care of the reset polarity. Signed-off-by: Kayla Theil <kayla.theil@mixed-mode.de>
2019-10-15dm: pinctrl: introduce PINCONF_RECURSIVE optionPatrick Delaunay
In the Linux pinctrl binding, the pin configuration nodes don't need to be direct children of the pin controller device (may be grandchildren for example). This behavior is managed with the pinconfig u-class which recursively bind all the sub-node of the pin controller. But for some binding (when pin configuration is only children of pin controller) that is not necessary. U-Boot can save memory and reduce the number of pinconf instance when this feature is deactivated (for arch stm32mp for example for SPL). This patch allows to control this feature with a new option CONFIG_PINCONF_RECURSIVE when it is possible for each individual pin controller device. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2019-10-14Merge tag 'u-boot-imx-20191014' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-imx u-boot-imx-20191014 ------------------- Travis: https://travis-ci.org/sbabic/u-boot-imx/builds/597498628 - logicpd pinmux - i.MX7ULP: imx_ddr_size - fixes Toradex i.MX6/i.MX7 - pico-imx7d - tpc70 converted to DM - New Board: meerkat96 - add HAB version command - i.MX8 : imx8: Jump from alias to OCRAM address at SPL init imx8qm/qxp: Set SPL TEXT base to OCRAM base
2019-10-14Merge tag 'video-for-2020.01' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-video - panel bridge support in stm32 ltdc - DSI host uclass - sandbox DSI host uclass test driver and DSI host test - MIPI DSI helpers - Synopsys Designware MIPI DSI host bridge driver - STM32 DSI controller driver - OTM800A and RM68200 panel support - DSI host updates for stm32f769 and stm32mp1 dtsi files - splash screen for stm32f769 and stm32mp1 boards - stm32 defconfig updates for display support
2019-10-14Merge tag 'mmc-10-10-2019' of ↵Tom Rini
https://gitlab.denx.de/u-boot/custodians/u-boot-mmc - Add sdhci driver for Broadcom iProc platform - Add a driver callback for power-cycle for mmc - Implement host_power_cycle callback for stm32_sdmmc2 - spl: dm_mmc: Initialize only the required mmc device
2019-10-14i2c: imx_lpi2c: add ipg clkPeng Fan
The controller needs two clk, per clk and ipg clk, so let's add ipg clk. Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-13video: add support of panel RM68200Yannick Fertré
Support for Raydium RM68200 720p dsi 2dl video mode panel. This rm68200 panel driver is based on the Linux Kernel driver from drivers/gpu/drm/panel/panel-raydium-rm68200.c. Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
generated by cgit (git 2.34.1) at 2024-12-26 13:25:46 +0000