| Age | Commit message (Collapse) | Author |
|---|
|
The SDHCI is introduced by sama5d2, named as Secure Digital Multimedia
Card Controller(SDMMC). It supports the embedded MultiMedia Card (e.MMC)
Specification V4.41, the SD Memory Card Specification V3.0, and the SDIO
V3.0 specification. It is compliant with the SD Host Controller Standard
V3.0 specification.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
According to the SDHC specification, stopping the SD Clock is by setting
the SD Clock Enable bit in the Clock Control register at 0, instead of
setting all bits at 0.
Before stopping the SD clock, we need to make sure all SD transactions
to complete, so add checking the CMD and DAT bits in the Presen State
register, before stopping the SD clock.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
|
|
When detecting SDHC Adapter Card Type 2(SD/MMC Legacy Adapter Card),
enable EVDD automatic control via SDHC_VS. This could support SD card
IO voltage switching for UHS-1 speed mode.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
If adapter card type identification is supported for platform, we would
enable dat[4:7] for eMMC4.5 Adapter Card.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
commit b8e5b07225 "Powerpc: eSDHC: Fix mmc read write err in uboot of
T4240QDS board", T4160 also needs this fix.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Add 32bpp framebuffer support for the Atmel HLCDC driver. This is
needed for output bpp higher than 16bpp.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
Global variables are bad. Get rid of this particular one, so we can
correctly instantiate multiple atmel mci interfaces, without having
them interfere with one another.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
Instead of passing just the register area as a private data, introduce
a proper struct atmel_mci_priv structure instead. This will become useful
in the subsequent patch, where we eliminate the global variable from this
driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
[fix free()]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
After silencing the prints which were generated when reconfiguring the
clock of the SD/MMC bus, surprisingly, the driver stopped working such
that every attempt to use the SD/MMC bus caused the CPU to get totally
stuck hard. It turns out that the prints generated a short delay, which
was necessary for the CPU to reconfigure the clock without getting stuck.
Thus, this patch adds a short delay after the clock configuration instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
This driver generates clearly debugging prints when changing clock
speed, so silence those. Furthermore, the driver generates further
prints in case a command fails to complete. The later case woud be
useful, but for eMMC, command 8 can fail and it's not an error but
a part of the specification. Thus, make this debug() as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
[fix checkpatch warnings]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
|
|
|
|
SR_IE(Self-refresh interrupt enable) is needed for
Hardware Based Self-Refresh. Make it configurable and let
board code handle the rest.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
|
|
dev->uclass->uc_drv->per_device_auto_alloc_size is to be freed in
device_free(), so is dev->seq. Remove these unnecessary codes.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
In pch_gbe_probe(), some additional resources are allocated
(eg: mdio, phy). We should free these in the driver remove phase.
Add pch_gbe_remove() to clean it up.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
In designware_eth_probe(), some additional resources are allocated
(eg: mdio, phy). We should free these in the driver remove phase.
Add designware_eth_remove() to clean it up.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
|
|
In phy_connect_dev(), if the phy device has an accociated mac device
before, a warning message will be printed. But we should test the
old device against the new one, if they are actually the same one,
don't print the warning message.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
In get_phy_device_by_mask(), when no phy is found, currently we only
print a message to show the first phy address that is not found. But
this is not always the case as multiple phys can be specified by
phy_mask. Change to print all phys that are not found, and to reduce
the console boot log, change to use 'debug' instead of 'printf'.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
In get_phy_device_by_mask(), when no phy is found, we should not
create any phy device.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
NAND-tree is used to check wiring between MAC and PHY using NAND gates
on the PHY side, hence the name.
NAND-tree initial status is latched at reset by probing the IRQ pin.
However some devices are sharing the PHY IRQ pin with other peripherals
such as Atmel SAMA5D[34]x-EK boards when using the optional TM7000
display module, therefore they are switching the PHY in NAND-tree test
mode depending on the current IRQ line status at reset.
This patch ensure PHY is not in NAND-tree test mode only for the Micrel
KSZ8051 PHY used by Atmel. There are other Micrel PHY affected but I
doubt they are used on such weird hardware design.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Casting from dev->priv to pci_dev_t changes the value's size on a 64-bit
system. This causes the compiler to complain about casting a pointer to an
integer of a different (smaller) size. To avoid this, cast to an integer
of matching size first, then perform an int->int cast to perform the size
change. This signals explicitly that we do want to change the size, and
avoids the compiler warning. This is legitimate since we know the pointer
actually stores a small integer, not a pointer value.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
This patch adds support for Micrel KSZ8021RNL & KSZ8031RNL.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
Using NAKs on empty RX fifo for bulk in transfers is the right choice
for a interrupt driven model, but U-Boot uses polling and expects an
immediate answer if there is no incoming packet. Using ZLP Bulk In Response
(BIR) mode avoids unexpected timeouts in the host controller driver.
As ZLP mode is reset default, there is no need to set it.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
This patch adds esdhc support for ls1043ardb.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
There are two LS series processors are built on ARMv8 Layersacpe
architecture currently, LS2085A and LS1043A. They are based on
ARMv8 core although use different chassis, so create fsl-layerscape
to refactor the common code for the LS series processors which also
paves the way for adding LS1043A platform.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
QSGMII PCS needed to be programmed same as SGMII PCS, and there are
four ports in QSGMII PCS, port 0, 1, 2, 3, all the four ports shared
port 0's MDIO controller, so when programming port 0, we continue to
program other three ports.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
The fsl_dtsec.h & fsl_tgec.h & fsl_fman.h can be shared on both ARM
and PPC, move it out of ppc to include/, and change the path in
drivers accordingly.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
codes related to phylib operations should be wrapped by CONFIG_PHYLIB.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
In convention, the '0' is a normal return value indicating there isn't
an error. While some functions of FMan IM driver treat '0' as an error
return value.
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
The FMan IM driver is developed for 32-bit platfroms and isn't
friendly to 64-bit platforms, so do the minimal refactor:
1. Refine the MURAM management and access.
2. Correct the initialization and operations for QDs and BDs.
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
The Frame Manager(FMan) is a big-endian peripheral, so the
registers, internal MURAM and BDs, which are allocated in main
memory and used to communication between core and FMan, should
be accessed in big-endian. The big-endian platforms can access
them directly as the code implemented so far, while for the
little-endian platforms it need to swap the byte-order.
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
Currently ldpaa ethernet driver rely on DPL file to statically configure
mac address for the DPNIs. It is not a correct approach.
Add support setting MAC address from env variable or Random MAC address.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
The SEC driver code has been cleaned up to work for 64 bit
physical addresses and systems where endianess of SEC block
is different from the Core.
Changes:
1. Descriptor created on Core is modified as per SEC block
endianness before the job is submitted.
2. The read/write of physical addresses to Job Rings will
be depend on endianness of SEC block as 32 bit low and
high part of the 64 bit address will vary.
3. The 32 bit low and high part of the 64 bit address in
descriptor will vary depending on endianness of SEC.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
|
|
|
|
smsc95xx_recv() does not reassemble bursts spread over multiple URBs.
If there is a lot of broadcast traffic, the fifo will fill up to the
burst cap limit. Lowering the burst cap to the URB size ensures no packet
spans multiple urbs.
Caveat, lower limit for working burst cap is 5/33 HS/FS packets.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
|
|
|
|
Do not enable both I2C controllers by default. Enable them only when
they are selected.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
|
|
- Moved macro definitions to top
- Give tab space to CONFIG_ALTERA_SPI_IDLE_VAL value
- Re-arrange header includes ascending order
Acked-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
Replace numerical bit shift with BIT macro
in altera_spi
:%s/(1 << nr)/BIT(nr)/g
where nr = 0, 1, 2 .... 31
Cc: Marek Vasut <marex@denx.de>
Acked-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
|
|
|
|
Replace numeric mask hexcodes with GENMASK macro
in xilinx_spi
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
Replace numeric mask hexcodes with GENMASK macro
in tegra*.c
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Tom Warren <twarren@nvidia.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
Replace numeric mask hexcodes with GENMASK macro
in omap3_spi
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
Replace numeric mask hexcodes with GENMASK macro
in fsl_qspi
Cc: York Sun <yorksun@freescale.com>
Cc: Haikun Wang <Haikun.Wang@freescale.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
Replace numeric mask hexcodes with GENMASK macro
in designware_spi
Cc: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
Replace numeric mask hexcodes with GENMASK macro
in atmel_spi
Cc: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
Replace numerical bit shift with BIT macro
in xilinx_spi
:%s/(1 << nr)/BIT(nr)/g
where nr = 0, 1, 2 .... 31
Cc: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
|
Replace numerical bit shift with BIT macro
in ti_qspi
:%s/(1 << nr)/BIT(nr)/g
where nr = 0, 1, 2 .... 31
Reviewed-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
|
