summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2019-02-09clk: stm32mp1: recalculate counter when switching freqPatrick Delaunay
Because stgen is initialized with HSI clock, we need to recalculate the counter when changing frequency. Signed-off-by: Lionel Debieve <lionel.debieve@st.com> Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-02-09clk: stm32mp1: correct access to RCC_OCENSETR/RCC_OCENCLRRPatrick Delaunay
Remove unnecessary setbits on set/clear registers. Avoid to deactivate HSI with HSE. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-02-09clk: stm32mp1: add IPCC clockPatrick Delaunay
Add support for enable/disable of IPCC clock using AHB3 registers Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-02-09clk: stm32mp1: no more get ck_usbo_48m in device treePatrick Delaunay
Remove support of ck_usbo_48m clock node in device tree, but force 48MHz frequency to prepare alignment with kernel device tree. Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-02-09drivers: serial: dm: Enable DM_FLAG_PRE_RELOC in SBSA pl011 uart driverVabhav Sharma
The DM_FLAG_PRE_RELOC shall be enabled in SBSA PL011 uart driver as this driver is used in NXP based SoCs It is necessary to have Serial console running before relocation The !CONFIG_IS_ENABLED(OF_CONTROL) [*] check is set as "workaround" for DM problem : 4687919684e This flag is set if board does not support device-tree and using platform data, In DM Model either of device tree or platform data can be used to fetch device configuration It is possible to use SBSA UART with CONFIG_DM_SERIAL but witout corresponding device tree description (OF_CONTROL) Other board/SoCs have this flag set unconditionally Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
2019-02-09watchdog: bcm6345: allow to use this driver on arm bcm6858Philippe Reynes
This IP is also used on some arm SoC, so we allow to use it on arm bcm6858 too. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
2019-02-09watchdog: bcm6345: switch to raw I/O functionsPhilippe Reynes
This driver is used on several big endian mips board. So we could use raw I/O function instead of forcing big endian access. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
2019-02-07Merge branch 'master' of git://git.denx.de/u-boot-spiTom Rini
- SPI-NOR support
2019-02-07configs: Don't use SPI_FLASH_BAR as defaultVignesh R
Now that new SPI NOR layer uses stateless 4 byte opcodes by default, don't enable SPI_FLASH_BAR. For SPI controllers that cannot support 4-byte addressing, (stm32_qspi.c, fsl_qspi.c, mtk_qspi.c, ich.c, renesas_rpc_spi.c) add an imply clause to enable SPI_FLASH_BAR so as to not break functionality. Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07mtd: spi: Add lightweight SPI flash stack for SPLVignesh R
Add a tiny SPI flash stack that just supports reading data/images from SPI flash. This is useful for boards that have SPL size constraints and would need to use SPI flash framework just to read images/data from flash. There is approximately 1.5 to 2KB savings with this. Based on prior work of reducing spi flash id table by Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07mtd: spi: Remove unused filesVignesh R
spi_flash and spi_flash_ids are no longer needed after SPI NOR migration. Remove them. Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07mtd: spi: Switch to new SPI NOR frameworkVignesh R
Switch spi_flash_* interfaces to call into new SPI NOR framework via MTD layer. Fix up sf_dataflash to work in legacy way. And update sandbox to use new interfaces/definitions Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07mtd: spi: sf_probe: Add "jedec, spi-nor" compatible stringVignesh R
Linux uses "jedec,spi-nor" as compatible string for JEDEC compatible SPI Flash device nodes. Therefore make U-Boot also to look for the same compatible string so that we can use Linux DTS files as is. Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07mtd: spi: spi-nor-core: Add back U-Boot specific featuresVignesh R
For legacy reasons, we will have to keep around U-Boot specific SPI_FLASH_BAR and SPI_TX_BYTE. Add them back to the new framework Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07mtd: spi: spi-nor-core: Add SFDP supportVignesh R
Sync Serial Flash Discoverable Parameters (SFDP) parsing support from Linux. This allows auto detection and configuration of Flash parameters. Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07mtd: spi: spi-nor-core: Add 4 Byte addressing supportVignesh R
Sync changes from Linux SPI NOR framework to add 4 byte addressing support. This is required in order to support flashes like MT35x that no longer support legacy Bank Address Register(BAR) way of accessing >16MB region. Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07mtd: spi: spi-nor-core: Add SPI MEM supportVignesh R
Many SPI controllers have special MMIO interfaces which provide accelerated read/write access but require knowledge of flash parameters to make use of it. Recent spi-mem layer provides a way to support such controllers. Therefore, add spi-mem support to spi-nor-core as a way to support SPI controllers with MMIO interface. SPI MEM layer takes care of translating spi_mem_ops to spi_xfer()s in case of legacy SPI controllers. Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07mtd: spi: Port SPI NOR framework from LinuxVignesh R
Current U-Boot SPI NOR support (sf layer) is quite outdated as it does not support 4 byte addressing opcodes, SFDP table parsing and different types of quad mode enable sequences. Many newer flashes no longer support BANK registers used by sf layer to a access >16MB of flash address space. So, sync SPI NOR framework from Linux v4.19 that supports all the above features. Start with basic sync up that brings in basic framework subsequent commits will bring in more features. Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07spi: Add non DM version of SPI_MEMVignesh R
Add non DM version of SPI_MEM to support easy migration to new SPI NOR framework. This can be removed once DM_SPI conversion is complete. Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07spi: spi-mem: Claim SPI bus before spi mem accessVignesh R
It is necessary to call spi_claim_bus() before starting any SPI transactions and this restriction would also apply when calling spi-mem operations. Therefore claim and release bus before requesting transfer via exec_op. Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07spi: spi-mem: Extend spi_mem_adjust_op_size() to honor max xfer sizeVignesh R
Extend spi_mem_adjust_op_size() to take spi->max_write_size and spi->max_read_size into account. Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07spi: spi-mem: Allow use of spi_mem_exec_op for all SPI modesVignesh R
SPI controllers support all types of SPI modes including dual/quad bus widths. Therefore remove constraint wrt SPI mode from spi-mem layer. Signed-off-by: Vignesh R <vigneshr@ti.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Jagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-05Merge git://git.denx.de/u-boot-marvellTom Rini
- Move Armada XP / 38x PCIe driver to DM_PCI from me - Move Armada XP / 38x LCD driver to DM_VIDEO from me - Add uDPU board (Armada-3720) from Vladimir [trini: Fix warning in pci-uclass.c by removing ret from pci_uclass_child_post_bind as it no longer calls functions with a return code to catch.] Signed-off-by: Tom Rini <trini@konsulko.com>II
2019-02-05video: Armada XP: Move driver to DM_VIDEOStefan Roese
This patch moves the Armada XP video / LCD driver to DM_VIDEO. With this move, the legacy interface board_video_init() is removed from the theadorable board code (only user of this video driver). The support via DT will be added in a separate patch. This patch also enables DM_VIDEO for the theadorable board, as this is needed to not break git bisect'ability. Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Anatolij Gustschin <agust@denx.de> Acked-by: Anatolij Gustschin <agust@denx.de>
2019-02-05pci: pci_mvebu: Add DM_PCI support and move CONFIG_PCI_MVEBU to defconfigStefan Roese
This patch adds DM_PCI support to the MVEBU PCIe driver. This is necessary, since all PCI drivers have to be moved to DM (driver model) until the v2019.07 release. To not break git bisect'ablility, this patch also moves CONFIG_PCI_MVEBU from config headers to the defconfig files. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Dirk Eibach <dirk.eibach@gdsys.cc> Cc: Mario Six <mario.six@gdsys.cc> Cc: Chris Packham <chris.packham@alliedtelesis.co.nz> Cc: Phil Sutter <phil@nwl.cc> Cc: Marek Behún <marek.behun@nic.cz> Cc: VlaoMao <vlaomao@gmail.com>
2019-02-05pci: Add pci_get_devfn() to extract devfn from the fdt_pci_addrStefan Roese
This function will be used by the Marvell Armada XP/38x PCIe driver, which is moved to DM right now. So let's extract the functionality from pci_uclass_child_post_bind() to make it available. Signed-off-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2019-02-02Merge tag 'for-master-20190201' of git://git.denx.de/u-boot-rockchipTom Rini
u-boot-rockchip changes for 2019.04-rc1: * support for Chromebook Bob * full pinctrl driver using DTS properties * documentation improvements * I2S support for some Rockchip SoCs
2019-02-02Merge tag 'mips-pull-2019-02-01' of git://git.denx.de/u-boot-mipsTom Rini
- MIPS: mscc: jr2: small fixes - MIPS: mscc: luton: add ethernet and switch driver - MIPS: mt76xx: fix timer frequency
2019-02-01regulator: pbias: Handle extended drain IO when changing omap36 PBIASAdam Ford
The OMAP36 and DM37 TRM state to disable extneded drain IO before changing the PBIAS. This patch does this before pmic writes if the CONFIG_MMC_OMAP36XX_PINS flag is set and the cpu family is omap36xx Signed-off-by: Adam Ford <aford173@gmail.com>
2019-02-01pinctrl: Kconfig: fix missing include of rockchip/KconfigPhilipp Tomsich
After the merge of the new, generic pinctrl-code, the include for rockchip/Kconfig was missing. Add it here, so we can select the pinctrl-driver for SPL. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-02-01pinctrl: Kconfig: sort includes alphabeticallyPhilipp Tomsich
To make adding new subdirectories easier, let's enforce alphabetical ordering of the includes of Kconfig files in the respective subdirectories. Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-02-01rockchip: Implement spl_gpio in the GPIO driverSimon Glass
Allow rockchip boards to use GPIOs before driver model is ready. This is really only useful for setting GPIOs to enable the early debug console, if needed on some platforms. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-02-01rockchip: clk: Add mention of four new clocksSimon Glass
These clocks are needed to get MMC running. We don't actually support setting them yet. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-02-01clk: Improve debug message in clk_set_default_rates()Simon Glass
It is helpful to print the clock number as well as the index, so that this can be looked up in the binding file. Update the debug() statement to do this. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-02-01pinctrl: rockchip: Clean the unused rockchip pinctrl driversDavid Wu
If we used the pinctrl-rockchip driver, these code is not needed, so remove them. Signed-off-by: David Wu <david.wu@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-02-01pinctrl: rockchip: Add common rockchip pinctrl driverDavid Wu
Use this driver to fit all Rockchip SOCs and to support the desired pinctrl configuration via DTS. Signed-off-by: David Wu <david.wu@rock-chips.com> Acked-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-02-01rockchip: Add a sound driverSimon Glass
Add a sound driver for rk3288 supporting chromebook_jerry. This uses the I2S driver, and existing audio codec and the clock/pinmux support. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-02-01rockchip: Add an I2S driverSimon Glass
Add a driver for I2S which allows audio data to be sent from the SoC to the audio codec. The sample rate and other settings are hard-coded for now as there is no suitable device-tree binding available. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-02-01rockchip: rk3288: Add i2s pinctrl and clock supportSimon Glass
Add support for setting pinctrl and clock for I2S on rk3288. This allows the sound driver to operate. These settings were created by rkmux.py Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2019-02-01usb: ether: call _usb_eth_halt() if initialization failsJean-Jacques Hiblot
If the host does not respond in time, the initialization fails. However the usb ether driver will still be registered. This will make usb_gadget_probe_driver() fail the next time the initialization is attempted because it cannot find an available UDC. Fixing this by calling _usb_eth_halt() when the init fails. Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Acked-by: Lukasz Majewski <lukma@denx.de>
2019-02-01net: Add MSCC Luton networkd driver.Horatiu Vultur
Add network driver for Microsemi Ethernet switch, it is present on Luton SoCs. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
2019-02-01net: mscc: Remove unused variablesHoratiu Vultur
Remove unused variables in the struct ocelot_private and make miim variable static. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
2019-02-01net: mscc: Move mac_table_add function into different file.Horatiu Vultur
Move the function mac_table_add into a different file, so it can be reused. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
2019-02-01net: mscc: Move ocelot_send and ocelot_recv in a different file.Horatiu Vultur
This functions can be reused by other MSCC SoCs therefore, make them more generic and move them in separate files. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
2019-02-01net: mscc: Move miim commands into separate file.Horatiu Vultur
Move miim functions that can be shared in a different file inside mscc_eswitch. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
2019-02-01net: mscc: Move ocelot_switch to mscc_eswitch folderHoratiu Vultur
Move file ocelot_switch to mscc_eswitch to prepare to add new net drivers for other MSCC SoCs. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
2019-01-31Merge tag 'video-updates-for-2019.04-rc1' of git://git.denx.de/u-boot-videoTom Rini
- ihs and imx driver fixes - relax EDID validation checks for 0 hsync/vsync pulse width (support some quirky displays)
2019-01-31video: Add Meson Video Processing Unit DriverNeil Armstrong
This adds video output support for Amlogic GXBB/GXL/GXM chips. The supported ports are CVBS and HDMI (based on DW_HDMI). When using HDMI, only DMT modes are supported. There is support for simple-framebuffer (CONFIG_VIDEO_DT_SIMPLEFB) Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Jorge Ramire-Ortiz <jramirez@baylibre.com> Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com> [narmstrong: fixed defines alignment in meson_canvas.c] Reviewed-by: Anatolij Gustschin <agust@denx.de>
2019-01-31video: dw_hdmi: add support for color conversionJorge Ramirez-Ortiz
Some IPs like the meson VPU can only feed a particular pixel format to dw_hdmi. As of now, the driver is hardcoded to use RGB888 as input. This commit enables different pixel format inputs, with the appropriate CSC configuration. Signed-off-by: Jorge Ramire-Ortiz <jramirez@baylibre.com> Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Anatolij Gustschin <agust@denx.de>
2019-01-31video: dw_hdmi: support SoC specific read/write opsJorge Ramirez-Ortiz
Some IPs like the meson VPU have a specific way to write to dw_hdmi registers. Make it configurable. Signed-off-by: Jorge Ramirez-Ortiz <jramirez@baylibre.com> [added commit description] Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Reviewed-by: Anatolij Gustschin <agust@denx.de>
generated by cgit (git 2.34.1) at 2025-02-02 02:30:45 +0000