| Age | Commit message (Collapse) | Author |
|---|
|
For some reason the spi_flash_probe_bus_cs() is called
inside the setup_flash_device() with zero values in place
of configurated SPI flash mode and maximum flash speed.
This code causes HALT error during startup environment
relocation on some platforms - namely Armada-38x-GP board.
Fix the function call by replacing zeros with the appropriate
values - CONFIG_ENV_SPI_MAX_HZ and CONFIG_ENV_SPI_MODE.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
|
|
Add missing environment name for UBI, to prevent this NULL in output:
Loading Environment from <NULL>...
and rather have a valid UBI there:
Loading Environment from UBI...
Signed-off-by: Marek Vasut <marex@denx.de>
|
|
There is no reason to have the same Kconfig options for different SoCs
separately. The patch is merging them together.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
[trini: Fix ENV_SIZE around ENV_IS_NOWHERE]
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
"Failed" error message from env_load() only clutters the log with
unnecessary details, as we already have all needed warnings by that
time. Example:
Loading Environment from FAT... MMC: no card present
** Bad device mmc 0 **
Failed (-5)
Let's only print it in case when DEBUG is defined to keep log clear.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
|
|
When called with ENVOP_SAVE, env_get_location() only returns the
gd->env_load_location variable without actually checking for
the environment location and priority.
This behaviour causes env_save() to fall into an infinite loop when
the low-level drv->save() call fails.
The env_save() function should not loop through the environment
location list but it should save the environment into the location
stored in gd->env_load_location by the last env_load() call.
Signed-off-by: Nicholas Faustini <nicholas.faustini@azcomtech.com>
Reviewed-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
|
|
Add Kconfig options SPL_ENV_* and TPL_ENV_* and simplify Makefile.
This allows SPL/TPL image has different environment setting from
full feature U-Boot.
Signed-off-by: York Sun <york.sun@nxp.com>
|
|
%s/remove/remote/
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
The error message should start with `## Error: ` so that it's easily
detectable by tests without needing to have a complex regexp for
matching all possible error message patterns.
Let's add the `## Error: ` prefix to the error messages since it's the
one already in use.
Suggested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
|
|
The function set_default_env() sets the hashtable flags for import_r().
Formally set_default_env() doesn't accept flags from its callers. In
practice the caller can (un)set the H_INTERACTIVE flag, but it has to be
done using the first character of the function's string argument. Other
flags like H_FORCE can't be set by the caller.
Change the function to accept flags argument. The benefits are:
1. The caller will have to explicitly set the H_INTERACTIVE flag,
instead of un-setting it using a special char in a string.
2. Add the ability to propagate flags from the caller to himport(),
especially the H_FORCE flag from do_env_default() in nvedit.c that
currently gets ignored for "env default -a -f" commands.
3. Flags and messages will not be coupled together. A caller will be
able to set flags without passing a string and vice versa.
Please note:
The propagation of H_FORCE from do_env_default() does not introduce any
functional changes, because currently himport_r() is set to destroy the
old environment regardless if H_FORCE flag is set or not. More changes
are needed to utilize the propagation of H_FORCE.
Signed-off-by: Yaniv Levinsky <yaniv.levinsky@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
|
|
The function set_default_vars() in common.c adds H_INTERACTIVE to the
h_import() flag, but the function has no way of telling if the command
actually was user directed like this flag suggest. The flag should be
set by the calling function do_env_default() in nvedit.c instead, where
the command is certainty user directed.
Move the H_INTERACTIVE flag from set_default_vars() to do_env_default().
Signed-off-by: Yaniv Levinsky <yaniv.levinsky@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
|
|
The env_flag in do_env_default() doesn't get propagated and therefore
gets ignored by himport_r(). This breaks to ability to "forcibly" reset
variables to their default values using the environment command.
Scenario example of the problem:
# setenv kernel uImage
# setenv .flags kernel:so
# env default -f kernel
## Error: Can't overwrite "kernel"
himport_r: can't insert "kernel=zImage" into hash table
Change the call path so it will pass the flag correctly.
Signed-off-by: Yaniv Levinsky <yaniv.levinsky@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
|
|
This patch added support to enable CONFIG_ENV_SIZE, CONFIG_ENV_OFFSET
and CONFIG_ENV_SECT_SIZE through Kconfig for Zynq and Zynqmp.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
If ENV_IS_IN_EXT4 is set you shouldn't be able to select ENV_IS_NOWHERE.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Petr Vorel <petr.vorel@gmail.com>
|
|
's/environemnt/environment/' and
's/Environemnt/Environment/'
Signed-off-by: Shyam Saini <shyam@amarulasolutions.com>
|
|
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
For CONFIG_ENV_FAT_INTERFACE != 'mmc' a link error
env/fat.c:93: undefined reference to `mmc_initialize'
occurs if CONFIG_MMC_SUPPORT is not enabled.
Fixes: 26862b4a40c3 ("env: mmc/fat/ext4: make sure that the MMC sub-system
is initialized before using it")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
|
|
Relocate env drivers if manual relocation is enabled. This
patch fixes the issue of u-boot hang incase if env is
present in any of the flash devices.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Convert CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to Kconfig
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Petr Vorel <petr.vorel@gmail.com>
Reviewed-by: Petr Vorel <petr.vorel at gmail.com>
|
|
Use CONFIG_IS_ENABLED to see if CONFIG_BLK is enabled. Otherwise
SPL compilation breaks on boards which do have CONFIG_BLK enabled but
not DM_MMC for the SPL as follows:
env/mmc.c: In function ‘init_mmc_for_env’:
env/mmc.c:164:6: warning: implicit declaration of function ‘blk_get_from_parent’; did you mean ‘efi_get_ram_base’? [-Wimplicit-function-declaration]
if (blk_get_from_parent(mmc->dev, &dev))
^~~~~~~~~~~~~~~~~~~
efi_get_ram_base
env/mmc.c:164:29: error: ‘struct mmc’ has no member named ‘dev’
if (blk_get_from_parent(mmc->dev, &dev))
^~
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
|
|
Modifying the default environment via CONFIG_EXTRA_ENV_SETTINGS is
somewhat inflexible, partly because the cpp language does not allow
appending to an existing macro. This prevents reuse of "environment
fragments" for different boards, which in turn makes maintaining that
environment consistently tedious and error-prone.
This implements a Kconfig option for allowing one to define the entire
default environment in an external file, which can then, for example, be
generated programmatically as part of a Yocto recipe, or simply be kept
in version control separately from the U-boot repository.
Tested-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
|
|
Commit 7653942b10e9e ("common/env_embedded.c: drop support for
CONFIG_SYS_USE_PPCENV") dropped the .ppcenv section which was
used in linking scripts to allow fine placement of embedded
environment sections.
This implies that GCC randomly places objects from env/embedded.o
and environment is not guaranteed to be located at the correct address:
04003df8 g F .text 00000038 mii_init
04004000 g O .text 00000004 env_size
04004004 g O .text 00002000 environment
04006004 g F .text 00000040 .hidden __lshrdi3
This patch restores this capability by allocating each object marked
with __UBOOT_ENV_SECTION__ into a different section. Hence
'environment' will be alone in .text.environment, allowing a
fine placement in u-boot.lds with:
. = DEFINED(env_offset) ? env_offset : .;
env/embedded.o (.text.environment)
Fixes: 7653942b10e9e ("common/env_embedded.c: drop support for CONFIG_SYS_USE_PPCENV")
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
|
|
Signed-off-by: Tom Rini <trini@konsulko.com>
|
|
Since the dawn of time for the Allwinner support in mainline U-Boot
we store the environment to the SD card and write directly at
544KB from the beginning of the device. This leads to problems when
the U-Boot proper image grows beyond 504KB and eventually overlaps.
With one release of having the environment preferably in a FAT
partition, let's now turn off the MMC variant fallback, so we get back
all the space we need to implement features.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
|
|
Introduce another difference from upstream (kernel) source in
fs/ubifs/super.c: adding preprocessor condition as y variable in
mount_ubifs() depends on CONFIG_UBIFS_SILENCE_MSG:
fs/ubifs/super.c:1337:15: error: variable ?y? set but not used [-Werror=unused-but-set-variable]
long long x, y;
Not setting CONFIG_UBIFS_SILENCE_MSG in am335x_igep003x_defconfig and
igep0032_defconfig. Although it was defined in their config headers, it
depends on CMD_UBIFS which is not set for them.
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Heiko Schocher <hs@denx.de>
|
|
using it
When booting from a non-MMC device, the MMC sub-system may not be
initialized when the environment is first accessed.
We need to make sure that the MMC sub-system is ready in even a non-MMC
boot case.
Therefore, initialize mmc before loading environment from it.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
|
|
With multiple environments, the 'get_char' callback for env
drivers does not really make sense any more because it is
only supported by two drivers (eeprom and nvram).
To restore single character loading for these drivers,
override 'env_get_char_spec'.
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Commit 7d714a24d725 ("env: Support multiple environments") added
static variable env_load_location. When saving environmental
variables, this variable is presumed to have the value set before.
In case the value was set before relocation and U-Boot runs from a
NOR flash, this variable wasn't writable. This causes failure when
saving the environment. To save this location, global data must be
used instead.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
When saving the environment on a platform which has DMA alignment
larger than the natural alignment, env_fat_save triggers a debug
message in file_fat_write:
Saving Environment to FAT... writing uboot.env
FAT: Misaligned buffer address (9df1c8e0)
OK
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
|
|
For the redundant environment configuration, env_sf_load still
contained duplicate code instead of using env_import_redund().
Simplify the code by only executing the load twice and delegating
everything else to env_import_redund.
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
For multiple env drivers to correctly implement fallback when
one environment fails to load (e.g. crc error), the return value
of env_import has to be propagated by all env driver's load
function.
Without this change, the first driver that succeeds to load an
environment with an invalid CRC return 0 (success) and no other
drivers are checked.
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
There is more common code in mmc, nand and ubi env drivers that
can be shared by moving to env_import_redund.
For this, a status/error value whether the buffers were loaded
are passed as additional parameters to env_import_redund.
Ideally, these are already returned to the env driver by the
storage driver. This is the case for mmc, nand and ubi, so for
this change, code deduplicated.
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
env_import (and env_import_redund) currently return 1 on success
and 0 on error. However, they are only used from functions
returning 0 on success or a negative value on error.
Let's clean this up by making env_import and env_import_redund
return 0 on success and -EIO on error (as was the case for all
users before).
Users that cared for the return value are also updated. Funny
enough, this only affects onenand.c and sf.c
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Now that we have everything in place to implement the transition scheme,
let's enable it by default.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Allow boards and architectures to override the default environment lookup
code by overriding env_get_location.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Now that we have everything in place in the code, let's allow to build
multiple environments backend through Kconfig.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The raw MMC environment directly calls into the MMC framework. Make sure
it's enabled before we can select it.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Since we want to have multiple environments, we will need to initialise
all the environments since we don't know at init time what drivers might
fail when calling load.
Let's init all of them, and only consider for further operations the ones
that have not reported any errors at init time.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Now that we have everything in place to support multiple environment, let's
make sure the current code can use it.
The priority used between the various environment is the same one that was
used in the code previously.
At read / init times, the highest priority environment is going to be
detected, and we'll use the same one without lookup during writes. This
should implement the same behaviour than we currently have.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Since we have global messages to indicate what's going on, the custom
messages in the environment drivers only make the output less readable.
Make the common code play a little nicer by removing all the extra output
in the standard case.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Since we have global messages to indicate what's going on, the custom
messages in the environment drivers only make the output less readable.
Make MMC play a little nicer by removing all the extra \n and formatting
that is redundant with the global output.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
Since we have global messages to indicate what's going on, the custom
messages in the environment drivers only make the output less readable.
Make FAT play a little nicer by removing all the extra \n and formatting
that is redundant with the global output.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Since we can have multiple environments now, it's better to provide a
decent indication on what environments were tried and which were the one to
fail and succeed.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Since we'll soon have support for multiple environments, the environment
saving message might end up being printed multiple times if the higher
priority environment cannot be used.
That might confuse the user, so let's make it explicit if the operation
failed or not.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
In preparation for the multiple environment support, let's introduce two
new parameters to the environment driver lookup function: the priority and
operation.
The operation parameter is meant to identify, obviously, the operation you
might want to perform on the environment.
The priority is a number passed to identify the environment priority you
want to retrieve. The lowest priority parameter (0) will be the primary
source.
Combining the two parameters allow you to support multiple environments
through different priorities, and to change those priorities between read
and writes operations.
This is especially useful to implement migration mechanisms where you want
to always use the same environment first, be it to read or write, while the
common case is more likely to use the same environment it has read from to
write it to.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The env_driver_lookup_default and env_get_default_location functions are
about to get refactored to support loading from multiple environment.
The name is therefore not really well suited anymore. Drop the default
part to be a bit more relevant.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The nvedit command is the only user of env_driver_lookup_default outside of
the environment code itself, and it uses it only to print the environment
it's about to save to during env save.
As we're about to rework the environment to be able to handle multiple
environment sources, we might not have an idea of what environment backend
is going to be used before trying (and possibly failing for some).
Therefore, it makes sense to remove that message and move it to the
env_save function itself. As a side effect, we also can get rid of the call
to env_driver_lookup_default that is also about to get refactored.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Make it select FS_FAT as well, because if it's not selected, enabling
ENV_IS_IN_FAT causes a Kconfig warning:
warning: (ENV_IS_IN_FAT) selects FAT_WRITE which has unmet direct dependencies (FS_FAT)
This also allows dropping some code from config_fallbacks.
Also drop the unnecessary help text about having to enable
CONFIG_FAT_WRITE - Kconfig automatically handles that.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
|
|
|
